Kein System

Wie blitze ich ein Bild - Permanent Outgoing Incomes
Gesperrt
derblondehans
Interessierter
Interessierter
Beiträge: 48
Registriert: Montag 22. April 2002, 17:52

Kein System

Beitrag von derblondehans »

Hallo,
wollte heute ein neues Image in meine Box einspielen.
Leider ist da was schiefgelaufen, jetzt kommt im Display nur noch "Kein System".
Hier noch das Log:

<debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-01.a8.2c.07.00.00-1f
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.1.112, My IP 192.168.1.134
debug: Sending TFTP-request for file E/Dbox/Dbox Bootmanager/ppcboot_writeflash
debug: Sending TFTP-request for file E/Dbox/Dbox Bootmanager/ppcboot_writeflash
debug: Sending TFTP-request for file E/Dbox/Dbox Bootmanager/ppcboot_writeflash
debug: Sending TFTP-request for file E/Dbox/Dbox Bootmanager/ppcboot_writeflash
debug: Sending TFTP-request for file E/Dbox/Dbox Bootmanager/ppcboot_writeflash
debug: Sending TFTP-request for file E/Dbox/Dbox Bootmanager/ppcboot_writeflash
debug:
TFTP failed, giving up...
boot net failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root/platform/nokia-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root/platform/mpc8xx-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root/platform/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root.new/platform/nokia-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root.new/platform/mpc8xx-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /root.new/platform/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /lost+found/root/platform/nokia-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /lost+found/root/platform/mpc8xx-dbox2/kernel/os failed

Flash-FS bootstrap loader (v1.5)

Flash superblock not ok: No bootrecord
boot flash /lost+found/root/platform/kernel/os failed
dbox2:root>


Hat jemand einen Tip?

Gruß Hans
wolgade
Semiprofi
Semiprofi
Beiträge: 1313
Registriert: Donnerstag 2. Dezember 2004, 00:18
Kontaktdaten:

Re: Kein System

Beitrag von wolgade »

Eventuell falsches Image geflasht? Boxen mit zwei Flashbausteinen brauchen ein 2x_Image, Boxen mit einem Flashchip (meines Wissens nur Sagem) brauchen ein 1x_Image.

Du wirst die Kiste neu flashen müssen. Das geht mit Bootmanager oder Imageflashingassistent.
derblondehans
Interessierter
Interessierter
Beiträge: 48
Registriert: Montag 22. April 2002, 17:52

Re: Kein System

Beitrag von derblondehans »

Hallo,
kriege die Box nicht geflasht.
Jemand noch einen Tip?

Gruß Hans
MTM
Foren-Moderator
Beiträge: 944
Registriert: Freitag 21. Januar 2005, 16:18

Re: Kein System

Beitrag von MTM »

Hallo,
ja, mehr Input = mehr Output.
Da du nicht sagst, was genau du alles gemacht hast, sollen wir da immer und immerwieder alles für jeden Einzelnen vorkauen? Dies hier ist keine Hotline. Trotzdem wird dir geholfen, wenn du ein wenig mitarbeitest.

- Wie Box und Pc verbunden?
- Welches Programm verwendet?
- "boot net failed" ist dein Problem (=Suchwort)

MfG,
MTM.
derblondehans
Interessierter
Interessierter
Beiträge: 48
Registriert: Montag 22. April 2002, 17:52

Re: Kein System

Beitrag von derblondehans »

So,

1. zum Image:

Ich habe ein falsches Yadiimage (Yadi Snapshot 2.2.0.5 - Das Image ist nur als mtd1 (root.squashfs) vorhanden!) eingespielt

2. erneuter Flashversuch:

Habe es mit dem D-BOX Imageflashingassistent versucht, verbunden mit Nullmodem und Crossoverkabel.
Es geht zwar was aber nicht alles, ich vermute mein Crossoverkabel ist defekt es rastet nicht sauber in die Buchse ein.
Ich werde mal morgen ein neues besorgen und dann es noch mal versuchen.

Hier ist das LOG:

½debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.1.225, My IP 192.168.1.202
debug: Sending TFTP-request for file u-boot
will verify ELF image, start= 0x800000, size= 140064
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000

U-Boot 1.3.4 (Tuxbox - Hallenberg.com) (Nov 29 2008 - 23:53:59)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: ##
done
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: ####################################
done
Bytes transferred = 179877 (2bea5 hex)

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'kernel-cdk'.
Load address: 0x100000
Loading: #################################################################
##########################################################
done
Bytes transferred = 627048 (99168 hex)
Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'u-initrd'.
Load address: 0x400000
Loading: #################################################################
##################################################
done
Bytes transferred = 587229 (8f5dd hex)
............................................................... done
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 626984 Bytes = 612.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 00400000 ...
Image Name: Ramdisk Image
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 587165 Bytes = 573.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Ramdisk to 01f1f000, end 01fae59d ... OK
Linux version 2.4.36.9-dbox2 (Hallenberg.com) (gcc version 3.4.6) #1 Sa 29. Nov 23:29:22 CET 2008
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/ram rw ip=192.168.1.202:192.168.1.225:::::off
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30348k available (1048k kernel code, 324k data, 72k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGÿttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1a:6e:83
RAMDISK driver initialized: 16 RAM disks of 3333K size 1024 blocksize
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (rootfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
IP-Config: Guessing netmask 255.255.255.0
IP-Config: Complete:
device=eth0, addr=192.168.1.202, mask=255.255.255.0, gw=255.255.255.255,
host=192.168.1.202, domain=, nis-domain=(none),
bootserver=192.168.1.225, rootserver=192.168.1.225, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 573k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 72k init
init started: BusyBox v1.13.0 (2008-11-29 23:52:02 CET
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface

dbox2 - ImageFlashingAssistent 3.x

- Hallenberg.com -


Schreibe Backup: 8064k von 8064k (100%)
Lade Flashimage...

-------------------------------------------------------------
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\u-boot
TFTP: Transfer erfolgreich beendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\logo-lcd
TFTP: Transfer erfolgreich beendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\logo-fb
TFTP: Transfer erfolgreich beendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\kernel-cdk
TFTP: Transfer erfolgreich beendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\u-initrd
TFTP: Transfer erfolgreich beendet
TFTP: Sende C:\Dbox\V1.7\alexW2xImageV1[1].7.1.200402171738r.img
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich

------ Zusatzinformationen ------
Gewählter Netzwerkadapter: ELPC3R Ethernet Adapter (0)
IP-Adresse des Netzwerkadapters: 192.168.1.225
IP-Adresse die die dbox bekommt: 192.168.1.202
Betriebssystem: Microsoft Windows 98
CPU 1: Intel Pentium @ 120 MHz
Dateiname des Images: alexW2xImageV1[1].7.1.200402171738r.img
Imagetyp: Zwei Flashs
DBOX-IFA Version: 3.2
------ Powered by http://www.dboxservice-hallenberg.de ------

½debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.1.225, My IP 192.168.1.202
debug: Sending TFTP-request for file u-boot
will verify ELF image, start= 0x800000, size= 140064
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000


U-Boot 1.3.4 (Tuxbox - Hallenberg.com) (Nov 29 2008 - 23:53:59)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: ##
done
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: ####################################
done
Bytes transferred = 179877 (2bea5 hex)

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'kernel-cdk'.
Load address: 0x100000
Loading: #################################################################
##########################################################
done
Bytes transferred = 627048 (99168 hex)
Using SCC ETHERNET device
TFTP from server 192.168.1.225; our IP address is 192.168.1.202
Filename 'u-initrd'.
Load address: 0x400000
Loading: #################################################################
##################################################
done
Bytes transferred = 587229 (8f5dd hex)
............................................................... done
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 626984 Bytes = 612.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 00400000 ...
Image Name: Ramdisk Image
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 587165 Bytes = 573.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Ramdisk to 01f1f000, end 01fae59d ... OK
Linux version 2.4.36.9-dbox2 (Hallenberg.com) (gcc version 3.4.6) #1 Sa 29. Nov 23:29:22 CET 2008
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/ram rw ip=192.168.1.202:192.168.1.225:::::off
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30348k available (1048k kernel code, 324k data, 72k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGÿttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1a:6e:83
RAMDISK driver initialized: 16 RAM disks of 3333K size 1024 blocksize
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (rootfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
IP-Config: Guessing netmask 255.255.255.0
IP-Config: Complete:
device=eth0, addr=192.168.1.202, mask=255.255.255.0, gw=255.255.255.255,
host=192.168.1.202, domain=, nis-domain=(none),
bootserver=192.168.1.225, rootserver=192.168.1.225, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 573k freed
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 72k init
init started: BusyBox v1.13.0 (2008-11-29 23:52:02 CET
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface

dbox2 - ImageFlashingAssistent 3.x

- Hallenberg.com -



Schreibe Backup: 8064k von 8064k (100%)
Lade Flashimage...
tftp: timeout
tftp: timeout
done.
Sende Backup...
While trying to open /tmp/flash.img: No such file or directory

Sie koennen die dbox jetzt ausschalten.
tftp: timeout
tftp: timeout
tftp: timeout
½debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: TransmiP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
boot: elfcopy failed: 16
dbox2:root> ½debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transming BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
boot: elfcopy failed: 16
dbox2:root> ½debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast

-------------------------------------------------------------
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\u-boot
TFTP: Transfer erfolgreich beendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\logo-lcd
TFTP: Transfer erfolgreich beendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\logo-fb
TFTP: Transfer erfolgreich beendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\kernel-cdk
TFTP: Transfer erfolgreich beendet
TFTP: Sende C:\PROGRAMME\DBOX_IFA\tftp\u-initrd
TFTP: Transfer erfolgreich beendet
TFTP: Sende C:\Dbox\V1.7\alexW2xImageV1[1].7.1.200402171738r.img
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
TFTP: Transfer nicht erfolgreich
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet
BootP: Request von 00509C1A6E83 erhalten
BootP: ARP-Eintrag mit IP: 192.168.1.202 und Mac: 00509C1A6E83 gesetzt
BootP: Antwort an 00509C1A6E83 gesendet




Gruß Hans
Zuletzt geändert von derblondehans am Donnerstag 29. Januar 2009, 20:24, insgesamt 1-mal geändert.
MTM
Foren-Moderator
Beiträge: 944
Registriert: Freitag 21. Januar 2005, 16:18

Re: Kein System

Beitrag von MTM »

Hallo,
abgesehen davon, daß du wohl kein noch älteres Image als das finden konntest (alexW2xImageV1[1].7.1.200402171738r.img), stört irgendwas die Übertrageung desselben, evtl Virenscanner / Firewall?

MfG,
MTM.
derblondehans
Interessierter
Interessierter
Beiträge: 48
Registriert: Montag 22. April 2002, 17:52

Re: Kein System

Beitrag von derblondehans »

Hallo,
das war noch auf dem alten Laptop.
Firewall / Virenscanner gibt auf dem Laptop nicht, wird eigentlich nicht mehr genutzt.
Ich vermute das Crossoverkabel hat ne Macke da es nicht mehr sauber einrastet.
Morgen versuche ich es mit einem neuen Crossoverkabel.
Was kannst Du zu dem Log sagen, was sagt das aus?
Ist überhaupt ein Zugriff per Netzwerk noch möglich?
Gruß Hans
MTM
Foren-Moderator
Beiträge: 944
Registriert: Freitag 21. Januar 2005, 16:18

Re: Kein System

Beitrag von MTM »

Hallo,
Fehler des Nullmodemkabels glaube ich weniger, weil vorher ja eine ganze Reihe an Dateien problemlos per TFTP übertragen wurden, nur dann das Image-File leider nichtmehr (aussderdem läuft TFTP übers Netzwerk).

MfG,
MTM.
derblondehans
Interessierter
Interessierter
Beiträge: 48
Registriert: Montag 22. April 2002, 17:52

Re: Kein System

Beitrag von derblondehans »

MTM hat geschrieben:Hallo,
Fehler des Nullmodemkabels glaube ich weniger, weil vorher ja eine ganze Reihe an Dateien problemlos per TFTP übertragen wurden, nur dann das Image-File leider nichtmehr (aussderdem läuft TFTP übers Netzwerk).

MfG,
MTM.
Nullmodemkabel ???

Ich meinte das Crossoverkabel

Gruß hans
MTM
Foren-Moderator
Beiträge: 944
Registriert: Freitag 21. Januar 2005, 16:18

Re: Kein System

Beitrag von MTM »

Hallo,
sorry, hast ja recht, da hab ich falsch gelesen. :dash:

MfG,
MTM.
derblondehans
Interessierter
Interessierter
Beiträge: 48
Registriert: Montag 22. April 2002, 17:52

Re: Kein System

Beitrag von derblondehans »

Ich glaube es gibt schlimmeres, z.B. das die Box Schrott ist.
Werde morgen mit neuem Nullmodemkabel berichten.

Gruß Hans
MTM
Foren-Moderator
Beiträge: 944
Registriert: Freitag 21. Januar 2005, 16:18

Re: Kein System

Beitrag von MTM »

Hallo,
derblondehans hat geschrieben:Nullmodemkabel ???

Ich [dachte du] meinte[st] das Crossoverkabel
:lol: :lol: :lol:

MfG,
MTM.
wolgade
Semiprofi
Semiprofi
Beiträge: 1313
Registriert: Donnerstag 2. Dezember 2004, 00:18
Kontaktdaten:

Re: Kein System

Beitrag von wolgade »

derblondehans hat geschrieben:Werde morgen mit neuem Nullmodemkabel berichten.
Nullmodemkabel? Du meinst wahrscheinlich das Netzwerkkabel. Wenn das eine Macke hat, dann tausch das mal aus! Netzwerkkabel mit Wackelkontakt machen manchmal lustige Sachen.
derblondehans
Interessierter
Interessierter
Beiträge: 48
Registriert: Montag 22. April 2002, 17:52

Re: Kein System

Beitrag von derblondehans »

MTM hat geschrieben:Hallo,
derblondehans hat geschrieben:Nullmodemkabel ???

Ich [dachte du] meinte[st] das Crossoverkabel
:lol: :lol: :lol:

MfG,
MTM.
Hallo,
ja das Crossoverkabel meinte ích, jetzt habe ich mich doch echt verschrieben :dash:
Bekomme gleich mein neues Crossoverkabel und dann werde ich berichten.

Gruß Hans
Zuletzt geändert von derblondehans am Freitag 30. Januar 2009, 19:46, insgesamt 1-mal geändert.
derblondehans
Interessierter
Interessierter
Beiträge: 48
Registriert: Montag 22. April 2002, 17:52

Re: Kein System

Beitrag von derblondehans »

Update:

So, mit dem neuen Crossoverkabel (nicht NullModem) konnte ich die Box neu flashen.

Gruß Hans

PS: Thema kann geschlossen werden
Gesperrt