D-Box 2 startet immer wieder im Debug Mode neu! Bitte helft!

Domestos & Derivate
Gesperrt
Markus88
Neugieriger
Neugieriger
Beiträge: 11
Registriert: Sonntag 8. November 2009, 21:12

D-Box 2 startet immer wieder im Debug Mode neu! Bitte helft!

Beitrag von Markus88 »

Hi Leute,

ich habe eine D-Box2 Nokia Sat mit Avia600 gekauft. Debug Mode ist aktiviert, doch Sie startet immer wieder neu! Ich habe auch den Flash nochmal resettet (Pin12) jedoch leider ohne Erfolg. Mit dem Hallenberg Assisstenten geht es auch nicht! Quasi das Gleiche (mit Nullmodemkabel + Lan). Es steht Lade Software und dann fängt alles wieder von vorne an!

Man steckt sie ein, dann kommt der Debug-Bildschirm, es steht Lade... und dann dauert es ca. 5 Sekunden und Sie startet wieder neu, d.h. alles fängt wieder von vorne an.

So sieht das LCD aus:

Bild

Warum steht bei dsID ff.ff......ff.ff?? Das finde ich seltsam! Was ist da los?

Hier noch ein Logfile mit dem D-Box2 Bootmanager, direkt nach dem einstecken an den Strom (es wiederholt sich, da sich die Box ja neustartet):
debug: DDF: Calibrating delay loop... debug: DDF: 67.95 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID ff-ff.ff.ff.ff.ff.ff-ff
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032

will verify ELF image, start= 0x800000, size= 154360
verify sig: 262
Branching to 0x40000


U-Boot 1.2.0 (Tuxbox) (Mar 11 2009 - 16:20:53)

CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ............ done.
env: found "console" with value ttyS0
env: found "baudrate" with value 9600
env: found "dbox_duplex" with value 0
env: found "lcd_inverse" with value 0
env: found "lcd_contrast" with value 15
FB: ready
LCD: ready

debug: DDF: Calibrating delay loop... debug: DDF: 67.95 BogoMIPS
debug: WATCHDOG RESET
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID ff-ff.ff.ff.ff.ff.ff-ff
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032

will verify ELF image, start= 0x800000, size= 154360
verify sig: 262
Branching to 0x40000


U-Boot 1.2.0 (Tuxbox) (Mar 11 2009 - 16:20:53)

CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ............ done.
env: found "console" with value ttyS0
env: found "baudrate" with value 9600
env: found "dbox_duplex" with value 0
env: found "lcd_inverse" with value 0
env: found "lcd_contrast" with value 15
FB: ready
LCD: ready (usw. fängt immer wieder von vorne an)
Ich hoffe ihr könnt mir helfen! Vielen Dank!
juergeli
Interessierter
Interessierter
Beiträge: 22
Registriert: Mittwoch 9. Dezember 2009, 20:07

Re: D-Box 2 startet immer wieder im Debug Mode neu! Bitte he

Beitrag von juergeli »

mach mal den Selbstest (Power+oben halten, dann nur die Power-Taste loslassen) und schau mal nach was da im Bootlog kommt. Ich tippe mal, daß beim Speichertest ein Fehler erscheint, denn das Verhalten sieht nach Speicherfehler aus.
Markus88
Neugieriger
Neugieriger
Beiträge: 11
Registriert: Sonntag 8. November 2009, 21:12

Re: D-Box 2 startet immer wieder im Debug Mode neu! Bitte he

Beitrag von Markus88 »

Danke für deine Antwort! Also ich habe danach erstmal die Box nochmal geflasht (diesmal mit D-Box 2 Bootmanager)mit dem XXX Image leider wieder ohne Erfolg! Hier der Log beim flashen (er hat gemeint erfolgreich gefhlasht nach ein paar Minuten, war aber nicht so. Er hing immer bei Copy to flash):
debug: DDF: Calibrating delay loop... debug: DDF: 67.95 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID ff-ff.ff.ff.ff.ff.ff-ff
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.2.102, My IP 192.168.2.124
debug: Sending TFTP-request for file C/Programme/DBoxBoot/ppcboot_writeflash
will verify ELF image, start= 0x800000, size= 201596
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000


ppcboot 0.6.4 (Apr 11 2002 - 16:10:44)

Initializing...
CPU: PPC823ZTnnB2 at 67 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-42-96-7f
FLASH: 8 MB
LCD driver (KS0713) initialized
BOOTP broadcast 1
TFTP from server 192.168.2.102; our IP address is 192.168.2.124
Filename 'C/Programme/tftpboot/logo-lcd'.
Load address: 0x130000
Loading: ##
done
LCD logo at: 0x130000 (0x1F9FFC0 bytes)
BOOTP broadcast 1
TFTP from server 192.168.2.102; our IP address is 192.168.2.124
Filename 'C/Programme/tftpboot/logo-fb'.
Load address: 0x120000
Loading: #########
done
FB logo at: 0x0 (0x1FC0000 bytes)
AVIA Frambuffer
Input: serial
Output: serial


1: Console on ttyS0
2: Console on null
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
dbox2-ppcboot> bootp 120000 /C/1.img
BOOTP broadcast 1
TFTP from server 192.168.2.102; our IP address is 192.168.2.124
Filename '/C/1.img'.
Load address: 0x120000
Loading: #######################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
######################
done

dbox2-ppcboot> protect off 10020000 107fffff
...............................................................
Un-Protected 63 sectors

dbox2-ppcboot> erase 10020000 107fffff
Erase Flash from 0x10020000 to 0x107fffff
sector 66 .... done
Erased 63 sectors

dbox2-ppcboot> cp.l 120000 10020000 1F8000
Copy to Flash... done

dbox2-ppcboot>
Nachdem ich deinen Tipp ausprobiert hatte (Selbstetst) spuckte der Log folgendes aus:
debug: DDF: Calibrating delay loop... debug: DDF: 67.95 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID ff-ff.ff.ff.ff.ff.ff-ff
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: &_text 0x10000, &_etext 0x26218, &_data 0x26218, &_edata 0x29d08
debug: &_end 0x34894, &__stack 0x400000
debug: Memory tests (0x400000 -- 0x2000000)
debug: NumberTest: debug: passed
debug: MarchTest: debug: passed
debug: PermTest: debug: passed
dbox2:root>
Jetzt kommt aber das Unerklärliche: Nach deinem Selbstest bootete die Dbox ganz normal (mit einem XXX Image (das von mir? Oder das vom Vorgänger)) und ging nach dem Hochfahren aus bzw.in den Deep Stanyby (Grüne LED leuchtet). Hatte es leider nicht am Fernseher und konnte nix sehen. Hier der Log (hatte zufällig Nullmodem noch dran):
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032

will verify ELF image, start= 0x800000, size= 154360
verify sig: 262
Branching to 0x40000


U-Boot 1.2.0 (Tuxbox) (Mar 11 2009 - 14:20:53)

CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ............ done.
env: found "console" with value ttyS0
env: found "baudrate" with value 9600
env: found "dbox_duplex" with value 0
env: found "lcd_inverse" with value 0
env: found "lcd_contrast" with value 15
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (jffs2) loading 'vmlinuz' to 0x100000
### FS load complete: 646305 bytes loaded to 0x100000
............................................................... done
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 646241 Bytes = 631.1 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37-dbox2 (dbox@DboxCVS) (gcc version 3.4.6) #1 Di 17. Mr 14:56
:46 CET 2009
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,9600 dbox_duplex=0 root=/dev/mtdblock2 rw roo
tfstype=jffs2
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.92 BogoMIPS
Memory: 30876k available (1096k kernel code, 336k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled<6>eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42
:96:7f
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.2.1 (2008.07.25-11:34+0000) multi-call Thu Jan 1 01:0
0:00 UTC 1970
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
tuxbox: no IDE-Interface detected
Detected STB:
Vendor: Nokia
Model: D-BOX2
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter - GLJ-Team (JohnDoe,g5401) (C-Cube AViA GTX/eNX wit
h AViA 500/600).
DVB: registering frontend - http://xxx.6x.to 0:0 (VES1893)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $

Please press Enter to activate this console. [timerd] woke up from timer? false!

$Id: zapit.cpp,v 1.430glj 2009/04/08 14:00 GLJ-Team Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0
Killed
Killed
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 1 onid 85
/tmp/currentservices.xml: No such file or directory
$Id: controld.cpp,v 1.133 2009/02/24 19:09:09 seife Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[controld] format: 4:3(LB)
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
[EMU_START] Starte Camd2
[camd2] ca system id: 1702
avia_oss: IOCTL: SNDCTL_DSP_SPEED (arg=12000)

msgbox Message-Box Version 1.66
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_gt_pcm_set_rate(12000)
[camd2] no card is in slot #2
[camd2] no card is in slot #1
Segmentation fault
[camd2] no card is in slot #2
[camd2] no card is in slot #1
[camd2] card_country:
[camd2] card_number:
[camd2] card_version: ffff
[camd2] no card is in slot #2
[camd2] no card is in slot #1
lcdshot: /lib/libpng12.so.0: no version information available (required by lcdsh
ot)
avia_oss: IOCTL: SNDCTL_DSP_SPEED (arg=12000)
avia_gt_pcm_set_rate(12000)
lcdshot v0.7 GLJ-Team by JohnDoe based on lcshot by SnowHead
[nhttpd] Orginal Neutrino HTTP-Server starting. Developed GLJ-Team by JohnDoe w/
o y-Stuff v1.5d
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
$Id: sectionsd.cpp,v 1.glj.1 Exp $
[sectionsd] Caching max 2500 events
[sectionsd] Caching 1 days
[sectionsd] Caching 1 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
GLJ-Neutrino startet V3.80RT by GLJ-Team (JohnDoe)
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[basicsocket] receive timed out. waiting process 356
[CBasicClient] receive failed: /tmp/zapit.sock
[basicsocket] receive timed out. waiting process 368
[CBasicClient] receive failed: /tmp/zapit.sock
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[basicsocket] receive timed out. waiting process 356
[CBasicClient] receive failed: /tmp/zapit.sock
libpng error: Read Error
[neutrino/lcd] no valid setup background.
[lcdd] LCD-Init failed!
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)
[neutrino] setRepeat: delay=25 period=0 use kernel-repeat: no
[sectionsd] getUTC: read: Connection timed out
[basicsocket] send_data: Broken pipe
[zapit.cpp:sendBouquets:2202] could not send any return: Illegal seek
[basicsocket] send_data: Broken pipe
[basicsocket] send_data: Broken pipe
[zapit.cpp:send_data_count:2222] could not send any return: Broken pipe
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] received 19 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[neutrino] initialized everything
ERROR: CFrameBuffer::paintBoxRel called with dx < 0 (-65012)
Segmentation fault
[end_neutrino] gestartet
zapit shot down :)
Waiting for zapit (max. 9 seconds)
Waiting for zapit (max. 8 seconds)
Waiting for zapit (max. 7 seconds)
Waiting for zapit (max. 6 seconds)
Waiting for zapit (max. 5 seconds)
Waiting for zapit (max. 4 seconds)
Waiting for zapit (max. 3 seconds)
Waiting for zapit (max. 2 seconds)
Waiting for zapit (max. 1 seconds)
DBOX wird ausgeschaltet
CXA2092 found
The system is going down NOW !!
Sending SIGTERM to all processefp_cmd: i2c_transfer error (ret == -121)
[nhttpd] stop requested......
Sending SIGKILL to all processes.
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_core: masking unhandled irq reg 0 bit 7
Requesting system halt.
Nach deinem Hochfahren mit dem Image bootet Sie jetzt immer wieder wie anfangs! Ist doch verrückt! Was ist da los?

Vielen Dank!!!! Grüße
Striper
Erleuchteter
Erleuchteter
Beiträge: 625
Registriert: Samstag 8. September 2007, 16:17

Re: D-Box 2 startet immer wieder im Debug Mode neu! Bitte he

Beitrag von Striper »

Markus88 hat geschrieben: lcdshot v0.7 (UNERWÜNSCHTER INHALT, Anm. d. Forenbetreibers)-Team by JohnDoe based on lcshot by SnowHead
[nhttpd] Orginal Neutrino HTTP-Server starting. Developed (UNERWÜNSCHTER INHALT, Anm. d. Forenbetreibers)-Team by JohnDoe w/
o y-Stuff v1.5d
Mal dort fragen wo das Image her ist.
Stingray
Erleuchteter
Erleuchteter
Beiträge: 453
Registriert: Mittwoch 27. Juni 2007, 15:25
Kontaktdaten:

Re: D-Box 2 startet immer wieder im Debug Mode neu! Bitte he

Beitrag von Stingray »

Sieht nach defektem Ram bzw. Prozessor aus.
Gesperrt