Keine Sender

Anlaufschwierigkeiten? Was ist was? Worum geht's?
Antworten
Dave333
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Donnerstag 16. Juni 2011, 16:29

Keine Sender

Beitrag von Dave333 »

Hallo Leute,
ich habe heute mal wieder meine alte Dbox2 aus dem Keller freigeschaufelt. Dabei war eine Image von 2000 drauf das nicht mehr ging. Nun hab ich ein neues Image draufgehauen.Aber nun habe ich eine kleines Problem, trotz sender suche bzw Kanalsuche findet die DBox2 keine Sender. Danach habe ich eine Cables.xml eingespielt die so wie ich es gesehn habe nur die Frequenz geändert hat. Leider findet er immer noch keine Kanäle.

Dbox2 mit der neusten Image "neutrino-squashfs.img2x (15.06.2011 - 07:26)"


Die Kanalsuche läuft schon das zweite mal und aktuell bei 8min auf der Frequenz 810000000

Könnt ihr mir helfen?!
MTM
Foren-Moderator
Beiträge: 944
Registriert: Freitag 21. Januar 2005, 16:18

Re: Keine Sender

Beitrag von MTM »

Hallo,
welcher Kabelanbieter?
Hast du es mal mit fertigen Settings (Senderlisten) probiert? Die kannst du dir zB für Kabel Deutschland hier generieren lassen (gaaanz unten rechts auf "Die digitale Belegung... exportieren für Neutrino" klicken).

Bootlog?

MfG,
MTM.
Dave333
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Donnerstag 16. Juni 2011, 16:29

Re: Keine Sender

Beitrag von Dave333 »

Hay, danke für die Antwort,
ich hab die Senderliste eingefügt. Funktioniert leider immer noch nicht. Was ich jetzt noch seh beim Starten der Dbox das der uCode fehlt. Leider habe ich davon kein Backup und habe somit ziemlich versagt. Kann mir die jemmand geben bzw als zip hochladen? Die Sender sind drin und werden auch alle Angezeigt, nur fehlt der uCode und der Status bei den Sendern steht nur auf "Warte auf Uhrzeit..."

Code: Alles auswählen

Zdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0  mID 01
debug: feID 7a    gtxID 0b
debug: fpID 5a     dsID 01-63.f1.3c.07.00.00-ec
debug: HWrev X5  SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug: 
BOOTP/TFTP bootstrap loader (v0.3)
debug: 
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 173832
verify sig: 262
Branching to 0x40000


U-Boot 2010.03 (Tuxbox) (Jun 15 2011 - 07:21:25)

CPU:   PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.0
       Watchdog enabled
I2C:   ready
DRAM:  32 MB
FLASH:  8 MB
Scanning JFFS2 FS: . done.
env: found console with value ttyS0
env: found baudrate with value 9600
env: found dbox_duplex with value 0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
env: found lcd_bias with value 0
FB:    ready
In:    serial
Out:   serial
Err:   serial
Net:   SCC ETHERNET
LCD:   ready

Options:
  1: Console on null
  2: Console on ttyS0
  3: Console on framebuffer
Select option (1-3), other keys to stop autoboot:  0 
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 665652 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
   Image Name:   Linux-2.4.37.11-dbox2
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    665588 Bytes = 650 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Linux version 2.4.37.11-dbox2 (dietmarw@lalelu.li) (gcc version 3.4.6) #2 Wed Ju
n 15 07:21:37 CEST 2011
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 
dbox_duplex=0
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30840k available (1132k kernel code, 336k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:71:bd
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
 Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00580000 : "root (squashfs+lzma)"
0x00580000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.18.4 (2011-06-15 07:23:07 CEST)
starting pid 8, tty '': '/etc/init.d/sysinit'
[BOOT] running /etc/init.d/sysinit
Thu Jan  1 01:00:00 UTC 1970
starting pid 22, tty '': '/etc/init.d/rcS'

Please press Enter to activate this console. starting /etc/init.d/S05drivers ...

[BOOT] running /etc/init.d/S05drivers
tuxbox: no IDE-Interface detected
Detected STB:
        Vendor: Nokia
        Model: D-BOX2  (2 flash chips)
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
$Id: cam.c,v 1.32 2011/05/31 17:15:38 rhabarber1848 Exp $
cam: no firmware file found
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.105 2011/05/31 17:15:38 rhabarber1848 Exp $
avia_av_core.c: avia_av_firmware_read: Unable to load '/var/tuxbox/ucodes/avia50
0.ux'.
avia_av: microcode not found, setting up dummy
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.213 2011/05/31 17:15:38 rhabarber1848 Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters enabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.13 2011/05/22 15:16:34 rhabarber1848 Exp $

avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.206 2011/05/31 17:15:38 rhabarber1848 Exp 
$
starting /var/etc/init.d/S09lcdip ...
starting /etc/init.d/S10network ...
route: SIOCADDRT: Network is unreachable
starting /etc/init.d/S10rtc ...
starting /etc/init.d/S15syslogd ...
starting /etc/init.d/S18rdate ...
Jan  1 02:00:10 dbox syslog.info syslogd started: BusyBox v1.18.4
starting /etc/init.d/S20inetd ...
starting /etc/init.d/S25cdkVcInfo ...
starting /etc/init.d/S30autofs ...
[BOOT] Starting the automounter
starting /etc/init.d/S40tuxmaild ...
starting /etc/init.d/S99gui ...
Jan  1 02:00:14 dbox daemon.err automount[167]: failed to load map$Id: sectionsd
.cpp,v 1.321 2011/06/14 10:28:31 dbt Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[timerd] woke up from timer? false!
[camd] CA_SEND_MSG: No such device
[camd] CA_SEND_MSG: No such device
$Id: zapit.cpp,v 1.453 2010/10/26 20:10:42 dbt Exp $
[frontend] uncommitted_switch_mode 0 auto_fec 0
[getservices] /var/tuxbox/config/zapit/myservices.xml  found.
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 1 onid 85
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
/var/tuxbox/config/zapit/ubouquets.xml: No such file or directory
/tmp/currentservices.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
avia_av: new_audio_config timeout
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib
/liblcddisplay.so.0)
avia_av: new_audio_config timeout
[CVideo::setVideoFormat] output format: 4:3(LB)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[neutrino] SetupFonts filename: /share/fonts/micron.ttf fontname: Micron
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] init menus...
[neutrino] GUI-Personalize instance created...
[network config] Instance created
[neutrino] setRepeat: delay=25 period=0 use kernel-repeat: no
[drive_setup] Instance created
[neutrino] registering as event client
nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/l
iblcddisplay.so.0)
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[neutrino] init network setup...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
[scan-setup] received 10 providers
[neutrino] no file /var/tuxbox/config/init.end was found
[neutrino] initialized everything
zap failed!
[sectionsd] getUTC: read: Connection timed out
zap failed!
zap failed!
dietmarw
Contributor
Beiträge: 1833
Registriert: Mittwoch 10. April 2002, 15:39
Kontaktdaten:

Re: Keine Sender

Beitrag von dietmarw »

da die dateien nicht weitergegeben werden dürfen, sieht das hier schlecht aus..

aber du wirst lachen was man alles über google findet obwohl es nicht erlaubt ist..
Dave333
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Donnerstag 16. Juni 2011, 16:29

Re: Keine Sender

Beitrag von Dave333 »

Hmm das hab ich mir schon gedacht das die nicht weitergegeben werden. Jedoch kann ich die Dateien durch die Betanova auch nicht mehr zurückholen. Da ich beim Start der Dbox automatisch ein Ucode fehler erhalte.
Ebenfalls mal nebenbei ich hab noch eine zweite Dbox für Sat wenn ich die dazu verwende um die uCodes zu Entpacken ist das möglich? Wenn Ja, könnt ihr mir sagen wie ich den Fehler "Betriebsystem ist beschädigt" beheben kann?
dietmarw
Contributor
Beiträge: 1833
Registriert: Mittwoch 10. April 2002, 15:39
Kontaktdaten:

Re: Keine Sender

Beitrag von dietmarw »

dietmarw hat geschrieben:...was man alles über google findet obwohl es nicht erlaubt ist..
Dave333
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Donnerstag 16. Juni 2011, 16:29

Re: Keine Sender

Beitrag von Dave333 »

Hallo,
ich möcht jetzt doch auf Betanova zurückflashen.

Laut Wiki http://wiki.tuxbox-cvs.sourceforge.net/ ... va_flashen
Benötige ich die Img, die ist vorhanden!
Danach benötige ich diesen Generator für die .did datei.

So ab hier gehts nicht mehr weiter. Der Generator link ist nicht vorhanden. Könnt ihr mir einen funktionierenden Link nennen?!
MarcM
Foren-Moderator
Beiträge: 1119
Registriert: Sonntag 9. Juni 2002, 13:28

Re: Keine Sender

Beitrag von MarcM »

Hier ist das PHP Script noch, es geht auch. Du brauchst aber Webspace/PHP dafür....
http://www.tuxbox-cvs.sourceforge.net/f ... 39#p379139

Aber du könntest auch direkt nach ucodes suchen....

Marc
Dave333
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Donnerstag 16. Juni 2011, 16:29

Re: Keine Sender

Beitrag von Dave333 »

Hallo, die Ucodes habe ich bereits gefunden im Internet, habe Sie auch eingefügt. Jedoch gingen die Kanäle immer noch nicht. Jetzt will ich es einfach mal mit der Originalen Version testen ob überhaupt noch ein Kanal oder ein Sender geht. Vielleicht ist ja der Tuner für die Suche kaputt aber warum selbst nach der manuell eingefügten Liste die Kanäle immernoch nicht gingen weiß ich nicht.

Zurück zum Thema als ich komme nicht in den Forenbereich rein. Ebenfalls erhalte ich grade nach dem Flashen ein Fehlercode UC0. Es wäre für mich besser wenn mir jemmand über ICQ oder sonstwie Supporten könnte damit ich nichtandauernd im Forum warten müsste
MarcM
Foren-Moderator
Beiträge: 1119
Registriert: Sonntag 9. Juni 2002, 13:28

Re: Keine Sender

Beitrag von MarcM »

poste mal in komplettes Bootlog inkl Sendersuchlauf mit ucodes im Image...

Marc
Dave333
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Donnerstag 16. Juni 2011, 16:29

Re: Keine Sender

Beitrag von Dave333 »

Der Bootlog inkl. Sendersuchlauf und ucodes ist oben.

Momentan ist jetzt grade Betanova drauf mit nem UC0 Fehler. Wie ich den beheben kann weiß ich nicht oO
MarcM
Foren-Moderator
Beiträge: 1119
Registriert: Sonntag 9. Juni 2002, 13:28

Re: Keine Sender

Beitrag von MarcM »

Dave333 hat geschrieben:Der Bootlog inkl. Sendersuchlauf und ucodes ist oben.
wo ?
$Id: cam.c,v 1.32 2011/05/31 17:15:38 rhabarber1848 Exp $
cam: no firmware file found
.
.
avia_av_core.c: avia_av_firmware_read: Unable to load '/var/tuxbox/ucodes/avia500.ux'.
avia_av: microcode not found, setting up dummy
.
.
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters enabled.
In deinem Log oben sind definitiv keine uCodes reinkopiert worden..... eventuell die ucode.bin, die ist aber nicht nötig, da ggf. eine eingebaute (v0014) genommen wird falls sie fehlen sollte.... du brauchst die avia500.ux und eine cam-alpha.bin

Marc
MTM
Foren-Moderator
Beiträge: 944
Registriert: Freitag 21. Januar 2005, 16:18

Re: Keine Sender

Beitrag von MTM »

Hallo,
bis das mit dem php-Skript gefixt ist, hab ich dir mal die .did angehangen, die zu der dsid aus dem obigen Bootlog passt.
Zdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-63.f1.3c.07.00.00-ec
Die Datei im Zip mußt du noch umbenennen in .did (mit führendem Punkt).

MfG,
MTM.

PS: Der Fehlercode UC0 hat die fehlende bzw falsche .did als Ursache.
Du hast keine ausreichende Berechtigung, um die Dateianhänge dieses Beitrags anzusehen.
Dave333
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Donnerstag 16. Juni 2011, 16:29

Re: Keine Sender

Beitrag von Dave333 »

Code: Alles auswählen

Waiting for zapit (max. 9 seconds)
starting pid 219, tty '': '/etc/init.d/rcK'
stoping /etc/init.d/K99gui ...
stoping /etc/init.d/K40tuxmaild ...
stoping /etc/init.d/K30autofs ...
Stopping the automounter
/etc/init.d/K30autofs: line 69: can't open /var/run/automount.pid: no such file
kill: you need to specify whom to kill
stoping /etc/init.d/K25cdkVcInfo ...
stoping /etc/init.d/K20inetd ...
stoping /etc/init.d/K18rdate ...
stoping /etc/init.d/K15syslogd ...
stoping /etc/init.d/K10rtc ...
stoping /etc/init.d/K10network ...
stoping /etc/init.d/K09lcdip ...
stoping /etc/init.d/K05drivers ...
CXA2092 found
umount: can't umount /var: Device or resource busy
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0  mID 01
debug: feID 7a    gtxID 0b
debug: fpID 5a     dsID 01-63.f1.3c.07.00.00-ec
debug: HWrev X5  SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug: 
BOOTP/TFTP bootstrap loader (v0.3)
debug: 
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 173832
verify sig: 262
Branching to 0x40000


U-Boot 2010.03 (Tuxbox) (Jun 15 2011 - 07:21:25)

CPU:   PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.0
       Watchdog enabled
I2C:   ready
DRAM:  32 MB
FLASH:  8 MB
Scanning JFFS2 FS: . done.
env: found console with value ttyS0
env: found baudrate with value 9600
env: found dbox_duplex with value 0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
env: found lcd_bias with value 0
FB:    ready
In:    serial
Out:   serial
Err:   serial
Net:   SCC ETHERNET
LCD:   ready

Options:
  1: Console on null
  2: Console on ttyS0
  3: Console on framebuffer
Select option (1-3), other keys to stop autoboot:  0 
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 665652 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
   Image Name:   Linux-2.4.37.11-dbox2
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    665588 Bytes = 650 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Linux version 2.4.37.11-dbox2 (dietmarw@lalelu.li) (gcc version 3.4.6) #2 Wed Ju
n 15 07:21:37 CEST 2011
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 
dbox_duplex=0
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30840k available (1132k kernel code, 336k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:71:bd
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
 Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00580000 : "root (squashfs+lzma)"
0x00580000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.18.4 (2011-06-15 07:23:07 CEST)
starting pid 8, tty '': '/etc/init.d/sysinit'
[BOOT] running /etc/init.d/sysinit
Thu Jan  1 01:00:00 UTC 1970
starting pid 22, tty '': '/etc/init.d/rcS'

Please press Enter to activate this console. starting /etc/init.d/S05drivers ...

[BOOT] running /etc/init.d/S05drivers
tuxbox: no IDE-Interface detected
Detected STB:
        Vendor: Nokia
        Model: D-BOX2  (2 flash chips)
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
$Id: cam.c,v 1.32 2011/05/31 17:15:38 rhabarber1848 Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.105 2011/05/31 17:15:38 rhabarber1848 Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: AVIA 500 LB4 found, sptsfix is off
avia_av: microcode verify: 1 errors.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.213 2011/05/31 17:15:38 rhabarber1848 Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB121
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.13 2011/05/22 15:16:34 rhabarber1848 Exp $

avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.206 2011/05/31 17:15:38 rhabarber1848 Exp 
$
starting /var/etc/init.d/S09lcdip ...
starting /etc/init.d/S10network ...
route: SIOCADDRT: Network is unreachable
starting /etc/init.d/S10rtc ...
starting /etc/init.d/S15syslogd ...
starting /etc/init.d/S18rdate ...
Jan  1 02:00:10 dbox syslog.info syslogd started: BusyBox v1.18.4
starting /etc/init.d/S20inetd ...
starting /etc/init.d/S25cdkVcInfo ...
starting /etc/init.d/S30autofs ...
[BOOT] Starting the automounter
starting /etc/init.d/S40tuxmaild ...
starting /etc/init.d/S99gui ...
Jan  1 02:00:13 dbox daemon.err automount[162]: failed to load map$Id: sectionsd
.cpp,v 1.321 2011/06/14 10:28:31 dbt Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[timerd] woke up from timer? false!
[camd] ca system id: 1722
$Id: zapit.cpp,v 1.453 2010/10/26 20:10:42 dbt Exp $
[frontend] uncommitted_switch_mode 0 auto_fec 0
avia_gt_core: masking unhandled irq reg 0 bit 7
[getservices] /var/tuxbox/config/zapit/myservices.xml  found.
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 1 onid 85
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
/var/tuxbox/config/zapit/ubouquets.xml: No such file or directory
[camd] no card is in slot #2
[camd] no card is in slot #1
/tmp/currentservices.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[CVideo::setVideoFormat] output format: 4:3(LB)
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib
/liblcddisplay.so.0)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[neutrino] SetupFonts filename: /share/fonts/micron.ttf fontname: Micron
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] init menus...
[neutrino] GUI-Personalize instance created...
[network config] Instance created
[neutrino] setRepeat: delay=25 period=0 use kernel-repeat: no
[drive_setup] Instance created
[neutrino] registering as event client
[scan-setup] received 10 providers
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[neutrino] no file /var/tuxbox/config/init.end was found
[neutrino] initialized everything
zap failed!
nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/l
iblcddisplay.so.0)
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
zap failed!
[yhttpd] Webserver starting...
[sectionsd] getUTC: read: Connection timed out
Entschuldigung hier ist der richtige Bootlog.
Wegen der .did Danke für die Datei ich werd es später versuchen Sie einzufügen.
MarcM
Foren-Moderator
Beiträge: 1119
Registriert: Sonntag 9. Juni 2002, 13:28

Re: Keine Sender

Beitrag von MarcM »

avia_av: AVIA 500 LB4 found, sptsfix is off
avia_av: microcode verify: 1 errors.
Das wäre das einzige was mir auf den ersten Blick auffällt... hast du eventuell noch ne andere avia500.ux Datei die du probieren könntest ?

Marc
Dave333
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Donnerstag 16. Juni 2011, 16:29

Re: Keine Sender

Beitrag von Dave333 »

Hey,
also habe vier verschiedene Avia getestet ohne Erfolg.
Zu Betanova ich die Daten Extrahiert laut Anleitung aber wie soll ich das jetzt Patchen und die .did datei Einfügen?!
Ab dem OS blick ich grade nicht richtig durch kann mir das mal bitte jemmand ausführlicher erklären?
seife
Developer
Beiträge: 4189
Registriert: Sonntag 2. November 2003, 12:36

Re: Keine Sender

Beitrag von seife »

Ich denke, dein AVIA500 ist kaputt. Der "microcode verify" Fehler sagt, dass ein Wort (32bit), das aus dem AVIA DRAM gelesen wurde nicht gleich ist mit dem, was zuvor reingeschrieben wurde.

=> Box kaputt, reparatur eher nicht rentabel.
Dave333
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Donnerstag 16. Juni 2011, 16:29

Re: Keine Sender

Beitrag von Dave333 »

Was meinst du mit Reperatur nicht rentable? Das die Reperatur nicht lohnt wegen Kosten?
seife
Developer
Beiträge: 4189
Registriert: Sonntag 2. November 2003, 12:36

Re: Keine Sender

Beitrag von seife »

Ja. So ne dbox ist heute vielleicht noch 30€ wert, da rentiert es sich nicht, die auf- und wieder zuzuschrauben.
Wenn du natürlich passende RAMs rumliegen hast und die raus- und wieder reinlöten kannst und deine eigene Zeit nichts wert ist, dann ist das was anderes.
MTM
Foren-Moderator
Beiträge: 944
Registriert: Freitag 21. Januar 2005, 16:18

Re: Keine Sender

Beitrag von MTM »

Hallo,
wegen der Betanova-Geschichte: http://wiki.tuxbox-cvs.sourceforge.net/ ... va_flashen

MfG,
MTM.
Antworten