Yadi Snapshot 1.8.1.2 - 12.06.2004 23:06

[Bruno_W]

Ohje, jetzt noch verrückter ist: sichtbare Bildbereiche sind rot-grün-blau gestreift



Also, morgen Kabel besorgen, Bootlog machen. Bis dahin hilft nur Taste Rot, dann Blau.

Bruno

[elbarto]

Diese grünen Streifen im Bild hatte ich auch mal, du musst einfach nur das Bildschirmformat in den Videoeinstellungen umschalten.

[Tho!]

Hi,

dann will ich auch mal Feedback geben...

Bei mir geht mit dem Image garnichts.
Wenn ich auf einen Sender schalte, egal welchen, dann hab ich 2min Standbild, dann läufts kurz 5sekunden ganz ruckelig, und dann wieder standbild.
So kann man das beliebig fortsetzen.

Nach eimem reboot ists genauso.

**Phillips Avia 600**
*interne ucodes, 22er avia**

[rasc]

also, das Bild sieht eher aus, als wenn irgendein Programm im Speicher wildlaufen wuerde...

[essu]

[...]Bei mir geht mit dem Image garnichts.[...]

Dann paste doch bitte mal ein Log

[mash4077]

[...]Bei mir geht mit dem Image garnichts.[...]

Dann paste doch bitte mal ein Log

Bei ihm geht eher mit der Box garnichts...

http://forum.tuxbox-cvs.sourceforge.net ... p?p=207636

Gruß
mash

[Tho!]

Ich glaub net so richtig das es die Box is....
Die anderen Images gehen ja noch dem Flashen ein paar Stunden, das neue Yadi will garnicht.

Kanns auch am Sharp LNB (0,4) liegen?

[Bruno_W]

@mogway

Der Fehler mit den schwarezen Bildbereichen besteht nach wie vor. Hier das Bootlog:


U-Boot 1.1.1 (TuxBox) (May 28 2004 - 13:03:11)

CPU: PPC823ZTnnB2 at 65.900 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Philips, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (jffs2) loading 'vmlinuz' to 0x100000
Scanning JFFS2 FS: . .
### FS load complete: 610189 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 610125 Bytes = 595.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.25-dbox2 (mogway@yadi.org) (gcc version 3.3.3) #8 Mo Mai 31 00
:06:01 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock3 rootfstype=squashfs
Decrementer Frequency = 247125000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.53 BogoMIPS
Memory: 30908k available (1032k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:2d:88:ab
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x000e0000 : "kernel (jffs2)"
0x000e0000-0x006a0000 : "root (squashfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'0) multi-
Using /lib/modules/2.4.25-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.25-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.25-dbox2/misc/avs.o
Using /lib/modules/2.4.25-dbox2/misc/saa7126.o
Detected STB:
Vendor: Philips
Model: D-BOX2
Using /lib/modules/2.4.25-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.25-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.25-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.25-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.25-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.92 2004/05/31 15:34:34 carjay Exp $
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.47 2004/05/23 10:52:31 derget Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.206 2004/06/04 14:21:00 diemade Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.38 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.25-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/tda8044h.o
DVB: registering frontend 0:0 (TDA8044H QPSK Demodulator)...
Using /lib/modules/2.4.25-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.201 2004/06/04 14:03:01 ghostrider Exp $
Yadi Snapshot vom 12.06.2004 23:06 - Image-Version 1.8.1.2
Networkcfg eth0: 192.168.1.30/255.255.255.0 gw 192.168.1.1
Startmode: Neutrino - SPTS:off - HWS:on
Using /lib/modules/2.4.25-dbox2/kernel/net/sunrpc/sunrpc.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/cifs/cifs.o
Starting pid 88, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.176 2004/04/
29 09:11:13 metallica Exp $
caching 504 hours
events are old 180min after their end time
[camd] ca system id: 1702
$Id: zapit.cpp,v 1.354 2004/06/10 19:56:12 rasc Exp $
[camd] no card is in slot #2
[camd] a card is in slot #1
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $

[controld] Boxtype detected: (2, Philips D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] no card is in slot #2
[camd] a card is in slot #1
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[deutsch.locale] superfluous entry: cam.wrong
[deutsch.locale] superfluous entry: flashupdate.action
[deutsch.locale] superfluous entry: flashupdate.actionwriteflash
[deutsch.locale] missing entry: flashupdate.proxypassword_hint2
[deutsch.locale] superfluous entry: flashupdate.reboot
[deutsch.locale] superfluous entry: infoviewer.cantdecode
[deutsch.locale] superfluous entry: mainsettings.plugins
[deutsch.locale] superfluous entry: mainsettings.scan
[deutsch.locale] superfluous entry: miscsettings.boxtype
[deutsch.locale] superfluous entry: parentallock.onstart
[deutsch.locale] superfluous entry: recordingmenu.vcr_devicename
[deutsch.locale] superfluous entry: satsetup.extended_lnb
[deutsch.locale] superfluous entry: scants.services
[deutsch.locale] superfluous entry: streamfeatures.info
[deutsch.locale] superfluous entry: streaminfo.ecm_invalid
[deutsch.locale] superfluous entry: streaminfo.not_crypted
[deutsch.locale] superfluous entry: timerlist.empty
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] vcrControl Instance created
CVCRControl registered new vcr device: vcr
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] initialized everything
PES, queue 0 normal.
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3)
[sectionsd] readNbytes: received POLLERR
[sectionsd] readNbytes: received POLLERR
login[126]: root login on `pts/0'

Starting pid 129, console /dev/console: '/bin/switch'
STV6412 found
The system is going down NOW !!
Sending SIGTERM to all processe[nhttpd] stop requested......
Sending SIGKILL to all processes.
Please stand by while rebooting the system.
?debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.0 mID 02
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-79.96.df.07.00.00-f9
debug: HWrev 01 FPrev 0.30
debug: B/Ex/Fl(MB) 32/00/08
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Unknown RFC1048-tag debug: 3 debug: 4 debug: c0 debug: a8 debug: 1 debug:
1 debug:
debug: Unknown RFC1048-tag debug: 6 debug: 4 debug: c0 debug: a8 debug: 1 debug:
1 debug:
debug: Got BOOTP reply from Server IP 192.168.1.1, My IP 192.168.1.100
debug: Sending TFTP-request for file c0a80164
debug: Sending TFTP-request for file c0a80164
debug: Sending TFTP-request for file c0a80164
debug: Sending TFTP-request for file c0a80164
debug: Sending TFTP-request for file c0a80164
debug: Sending TFTP-request for file c0a80164
debug:
TFTP failed, giving up...
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/philips-dbox2/kernel/os in Flash-FS
debug: Got Block #0040

will verify ELF image, start= 0x800000, size= 152952
verify sig: 263
Branching to 0x40000


U-Boot 1.1.1 (TuxBox) (May 28 2004 - 13:03:11)

CPU: PPC823ZTnnB2 at 65.900 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Philips, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (jffs2) loading 'vmlinuz' to 0x100000
Scanning JFFS2 FS: . .
### FS load complete: 610189 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 610125 Bytes = 595.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.25-dbox2 (mogway@yadi.org) (gcc version 3.3.3) #8 Mo Mai 31 00
:06:01 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock3 rootfstype=squashfs
Decrementer Frequency = 247125000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.53 BogoMIPS
Memory: 30908k available (1032k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:2d:88:ab
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x000e0000 : "kernel (jffs2)"
0x000e0000-0x006a0000 : "root (squashfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'0) multi-
Using /lib/modules/2.4.25-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.25-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.25-dbox2/misc/avs.o
Using /lib/modules/2.4.25-dbox2/misc/saa7126.o
Detected STB:
Vendor: Philips
Model: D-BOX2
Using /lib/modules/2.4.25-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.25-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.25-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.25-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.25-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.92 2004/05/31 15:34:34 carjay Exp $
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.47 2004/05/23 10:52:31 derget Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.206 2004/06/04 14:21:00 diemade Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.38 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.25-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/tda8044h.o
DVB: registering frontend 0:0 (TDA8044H QPSK Demodulator)...
Using /lib/modules/2.4.25-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.201 2004/06/04 14:03:01 ghostrider Exp $
Yadi Snapshot vom 12.06.2004 23:06 - Image-Version 1.8.1.2
Networkcfg eth0: 192.168.1.30/255.255.255.0 gw 192.168.1.1
Startmode: Neutrino - SPTS:off - HWS:on
Using /lib/modules/2.4.25-dbox2/kernel/net/sunrpc/sunrpc.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/cifs/cifs.o
Starting pid 88, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.176 2004/04/
29 09:11:13 metallica Exp $
caching 504 hours
events are old 180min after their end time
[camd] ca system id: 1702
$Id: zapit.cpp,v 1.354 2004/06/10 19:56:12 rasc Exp $
[camd] no card is in slot #2
[camd] a card is in slot #1
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $

[controld] Boxtype detected: (2, Philips D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] no card is in slot #2
[camd] a card is in slot #1
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] Software update enabled
[neutrino] enable flash
[deutsch.locale] superfluous entry: cam.wrong
[deutsch.locale] superfluous entry: flashupdate.action
[deutsch.locale] superfluous entry: flashupdate.actionwriteflash
[deutsch.locale] missing entry: flashupdate.proxypassword_hint2
[deutsch.locale] superfluous entry: flashupdate.reboot
[deutsch.locale] superfluous entry: infoviewer.cantdecode
[deutsch.locale] superfluous entry: mainsettings.plugins
[deutsch.locale] superfluous entry: mainsettings.scan
[deutsch.locale] superfluous entry: miscsettings.boxtype
[deutsch.locale] superfluous entry: parentallock.onstart
[deutsch.locale] superfluous entry: recordingmenu.vcr_devicename
[deutsch.locale] superfluous entry: satsetup.extended_lnb
[deutsch.locale] superfluous entry: scants.services
[deutsch.locale] superfluous entry: streamfeatures.info
[deutsch.locale] superfluous entry: streaminfo.ecm_invalid
[deutsch.locale] superfluous entry: streaminfo.not_crypted
[deutsch.locale] superfluous entry: timerlist.empty
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] vcrControl Instance created
CVCRControl registered new vcr device: vcr
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[camd] set emm caid 1702 capid 1000
[neutrino] initialized everything
PES, queue 0 normal.
[camd] starting onid 0001 sid 0008
[camd] set emm caid 1702 capid 1000
descramble onid: 0001 sid: 0008 status: 1d1d
[controld] VIDEO_EVENT_SIZE_CHANGED 544x576 (4:3 -> 4:3)

Bruno

[lion3012]

Also,habe das Image vom 12.6
läuft Hundert Pro
teste seit 2 Tagen und bin mehr als Zufrieden
Bestes Image das ich bis Heute hatte !!!

Nur eine Sache stört Jedes mal wenn ich die Box neu starte,muß
ich ins Menue und "Netzwerkeinstellungen jetzt zuweisen" betätigen.

Alle Netzwerkeistellungen sind zwar noch richtig eingestellt aber bekomme keine Verbindung zur Box ??




Phillips

[mogway]

Nur eine Sache stört Jedes mal wenn ich die Box neu starte,muß ich ins Menue und "Netzwerkeinstellungen jetzt zuweisen" betätigen.

Lösch mal /var/etc/network/interfaces und setz die IP über den Maintainance Mode neu.

Gruss
mogway

[para]

FYI: das Video-Problem von bruno_w habe ich auch (trotz cold reboot)... Weiterhin besteht auch noch dieses Prob (seit dem 1.8.1.1er):

http://forum.tuxbox-cvs.sourceforge.net ... 785#207785

Ciao, Para

[lion3012]

Danke Mogway ! Nun klappts !

Der Tip war richtig










Phillips

[Konsi]

Das gleiche Problem mit den schwarzen Bereichen im Bild und mit den grünen Streifen hatte ich auch, neustart hat nicht gebracht, hab neu geflasht seit dem läufts eigentlich, was noch komisch ist, von Zeit zu Zeit kommt das Boot Logo von Yadi Schwarzweis, ein anderes mal wiederum Bunt, woran könnte das liegen, mit den vorrigen Images hatt ich die Probs nicht!

[Konsi]

Sorry habs vergessen zu erwähnen, ist ne Sagem 1xI Box!

[mogway]

Das gleiche Problem mit den schwarzen Bereichen im Bild und mit den grünen Streifen hatte ich auch[...]

Vllt mal ausprobieren:
http://forum.tuxbox-cvs.sourceforge.net ... 823#207823

Gruss
mogway

[lion3012]

Habe Sendersuchlauf gemacht,danach konnte JTG Senderliste nicht mehr einlesen ??????????

Habe wieder meine alten eingespielt und es geht damit wieder.

Woran kann das wogl liegen ????








Phillips

[mash4077]

...Woran kann das wogl liegen...

Hi,

erst alle Dateien unter "/var/tuxbox/config/zapit" löschen, dann Kanalsuche durchführen.

Gruß
mash

[lion3012]

Jau !! hatt geklappert

Thanks











Phillips

[unaek]

Hi,

ich hoffe mal das hier der richitge Platz für Bugs mit diesem Snapshot ist.

Habe es gleich mal draufgespielt und wollte etwas aufnehmen.
Machte das bisher mit dem DBox Winserver - problemlos.
Also Winserver gestartet - DBox zeigt dies auch an...
Einstellungen sind wie bisher und richtig. Alle Netzwerktests sind auch erfolgreich.
Mit dem Snapshot vom 12.06. ist die Aufnahmefunktion bei mir nicht mehr möglich.
Im Features Menü auf Aufnehmen führt zu 1 Minute Inaktivität mit anschließendem Fehlerpopup: Keine Verbindung zum Streamingserver. Aufnahme wird abgebrochen.
Dann kann man die Box wieder normal steuern, aber aufgenommen wird und wurde nix. Timeraufnahme endet auch nur in "Aufnahme beginnt in wenigen Minuten"
Hat jmd anders auch solche Erfahrungen gemacht?

Mittlerweile gehts wieder mit dem Snapshot vom 16.06.04 - naja egal warum Hauptsache es läuft

[tami]

* Neutrino: Neu: technische Information über den Stream, incl. Empfangsqualität

Kann mir jemand sagen wo ich hierzu mehr Infos finde.
Was bedeutet "BER" "SNR" "SIG" ?
Welche Werte sollte man bei einem guten Signal haben ?

greets,
Tami

[mogway]

1. BER: Bit Fehlerrate (sollte möglichs niedrig sein am Besten 0)
2. SNR: Signalqualität (je höher desto besser)
3. SIG: Signalstärke (je höher desto besser)

Gruss
mogway

[tami]

@ mogway
Danke