Seltsames Phänomen: hda: Lost Interrupt

to stream or not to stream
Antworten
MoonMan

Seltsames Phänomen: hda: Lost Interrupt

Beitrag von MoonMan »

Hallo,

bei meiner Nokia 2xFlash AVIA500 SAT ist seit in paar Tagen ein IDE/SATA Interface (selbst) eingebaut.
Leider wurde die angeschlossene Platte vom Interface nicht auf Anhieb korrekt formatiert / partitioniert und es begann die Fehlersuche,
hierbei experimentierte ich etwas und mir fiel folgendes auf:
Je nachdem welche, der mir zur Verfügung stehenden Platten angeschlossen ist wird ein
„hda: Lost Interrupt“ erzeugt. Unabhängig an welche Spannungsversorgung die Platte angeschlossen ist.

Bei den Festplatten handelt es sich um folgende Modelle:
alte 2,5'' Notebookplatte IBM 5400 DLGA 23080 (0.52A)
fabrikneue 2,5'' Platte Samsung 5400 HM160HC (0.85A)
Seagate Barracuda 7200 ST32508244

Die Notebookplatten (2,5'') wurden sowohl an der internen Spannungsversorgung als auch mit einem externen Netzteil (5V/12V) betrieben.
Die Seagate kann nur mit externen Power-Supply (5V/12V) betrieben werden.
Seltsamerweise wird der „Lost Interrupt“ nur bei den Notebookplatten und dann schon beim „booten“ der Dbox ausgelöst.
Dies ist auch an eines sehr langen Bootphase zu erkennen.

Die "problematischen" Notebook HDDs werden am PC einwandfrei erkannt und können dort partitioniert und formatiert werden.

Weiß jemand Abhilfe oder eine Tipp wie diese Problem gelöst werden kann oder gibt es hierfür bereits einen work-arround ?
Was sagen die Spezialisten dazu?


Grüße
MoonMan
dbt
Administrator
Beiträge: 2675
Registriert: Donnerstag 28. September 2006, 19:18
Kontaktdaten:

Re: Seltsames Phänomen: hda: Lost Interrupt

Beitrag von dbt »

Hast du ein Bootlog zum nachlesen?
MoonMan

Re: Seltsames Phänomen: hda: Lost Interrupt

Beitrag von MoonMan »

Hier die Bootlogs:

----------------------------------------------------------------------------------------------------------------------------------------------
DBOX & Seagate Barracuda:

Code: Alles auswählen

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.01.08 08:37:15 =~=~=~=~=~=~=~=~=~=~=~=
ûdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0  mID 01
debug: feID dd    gtxID 0b
debug: fpID 5a     dsID 01-4e.a6.43.07.00.00-e6
debug: HWrev X5  SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug: 
BOOTP/TFTP bootstrap loader (v0.3)
debug: 
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
debug: Got Block #0004
debug: Got Block #0008
debug: Got Block #0012
debug: Got Block #0016
debug: Got Block #0020
debug: Got Block #0024
debug: Got Block #0028
debug: Got Block #0032
debug: Got Block #0036


will verify ELF image, start= 0x800000, size= 173832
verify sig: 262
Branching to 0x40000


U-Boot 2010.03 (Tuxbox) (Jan 02 2011 - 07:21:35)

CPU:   PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
         *** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
       Watchdog enabled
I2C:   ready
DRAM:  32 MB
FLASH:  8 MB
Scanning JFFS2 FS:   .  | / - \ | / - \ |  done.

env: found console with value ttyS0
env: found baudrate with value 9600
env: found dbox_duplex with value 0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
env: found lcd_bias with value 0
FB:    ready
In:    serial
Out:   serial
Err:   serial
Net:   SCC ETHERNET
LCD:   ready

Options:
  1: Console on null
  2: Console on ttyS0
  3: Console on framebuffer
Select option (1-3), other keys to stop autoboot:  1  0 
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 669404 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
   Image Name:   Linux-2.4.37.10-dbox2
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    669340 Bytes = 653.7 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Linux version 2.4.37.10-dbox2 (dietmarw@lalelu.li) (gcc version 3.4.6) #2 Sun Jan 2 07:21:52 CET 2011
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex=0
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30828k available (1140k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1f:9a:7f
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
 Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00580000 : "root (squashfs+lzma)"
0x00580000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init

init started: BusyBox v1.17.3 (2011-01-02 07:23:51 CET)

starting pid 8, tty '': '/etc/init.d/sysinit'
[BOOT] running /etc/init.d/sysinit
Thu Jan  1 01:00:00 UTC 1970

starting pid 22, tty '': '/etc/init.d/rcS'

Please press Enter to activate this console. starting /etc/init.d/S05drivers ...
[BOOT] running /etc/init.d/S05drivers
tuxbox: IDE-Interface detected, Vendor: DboxBaer or kpt.ahab/Stingray
Detected STB:
Vendor: Nokia
Model: D-BOX2  (2 flash chips)
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
ves1x93: Detected ves1893a rev2
DVB: registering frontend 0:0 (VES1893)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.102 2010/05/25 19:58:20 dbt Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: AVIA 500 LB4 found, sptsfix is off
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
starting /var/etc/init.d/S06hdd ...
/var/etc/init.d/06hdd generated from neutrino ide/mmc/hdd drive-setup
07.01.2011 - 20:33:30
1.80  do not edit!
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
dboxide: $Id: main.c,v 1.14 2009/06/19 14:39:26 seife Exp $
ide: late registration of driver.
dboxide: activating cs2
dboxide: address space of IDE-Interface is at: 0xc3b93000
dboxide: IDE-Interface detected, Vendor: DboxBaer or kpt.ahab/Stingray
dboxide: sreset failed, status: 0x000a
Probing IDE interface ide0...
hdb: ST3250824A, ATA DISK drive
ide0 at 0x010-0x017,0x04e on irq 47
hdb: attached ide-disk driver.
hdb: host protected area => 1
hdb: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63
Partition check:
 /dev/ide/host0/bus0/target1/lun0: p1 p2
starting /var/etc/init.d/S07mounts ...
/var/etc/init.d/07mounts generated from neutrino ide/mmc/hdd drive-setup
07.01.2011 - 20:33:30
1.80  do not edit!
mount: using /var/etc/fstab
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
swapon: using /var/etc/fstab
Adding Swap: 136512k swap-space (priority -1)
starting /var/etc/init.d/S09lcdip ...
starting /etc/init.d/S10network ...
route: SIOCADDRT: Network is unreachable
starting /etc/init.d/S10rtc ...
starting /etc/init.d/S15syslogd ...
starting /etc/init.d/S18rdate ...
starting /etc/init.d/S20inetd ...
starting /etc/init.d/S25cdkVcInfo ...
starting /etc/init.d/S30autofs ...
[BOOT] Starting the automounter
starting /etc/init.d/S40tuxmaild ...
starting /etc/init.d/S99gui ...
Jan  1 02:00:17 dbox daemon.err automount[179]: failed to load map$Id: sectionsd.cpp,v 1.319 2010/02/21 10:14:15 rhabarber1848 Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[timerd] woke up from timer? false!
[camd] ca system id: 1702
$Id: zapit.cpp,v 1.453 2010/10/26 20:10:42 dbt Exp $
[frontend] uncommitted_switch_mode 0 auto_fec 0
/var/tuxbox/config/zapit/ubouquets.xml: No such file or directory
/tmp/currentservices.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[CVideo::setVideoFormat] output format: 4:3(LB)
neutrino: /lib/libpng12.so.0: no version information available (required by neutrino)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib/liblcddisplay.so.0)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[neutrino] SetupFonts filename: /share/fonts/micron.ttf fontname: Micron
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] init menus...
[neutrino] GUI-Personalize instance created...
[network config] Instance created
[neutrino] setRepeat: delay=25 period=0 use kernel-repeat: no
[drive_setup] Instance created
[neutrino] registering as event client
[scan-setup] received 31 sats
[CVideo::setVideoFormat] output format: 16:9
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[sectionsd] getUTC: read: Connection timed out
avia_gt_core: masking unhandled irq reg 0 bit 6
[zapit] tuned frequency does not match request. difference: 859
[camd] set emm caid 1702 capid 1000
PES, queue 0 normal.
avia_gt_core: masking unhandled irq reg 0 bit 7
[neutrino] no file /var/tuxbox/coavia_gt_core: masking unhandled irq reg 1 bit 15
nfig/init.end was found
[camd] set emm caid 1702 capid 1000
[neutrino] initialized everything
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3)
nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/liblcddisplay.so.0)
02:00:55.589 [timeThread] - 08.01.2011 08:38:31, tim: Sat Jan  8 08:38:31 2011
[neutrino] timeset event. difference is 1294468656 s, stepping...
02:00:55.756 [timeThread] Time set via DVB, going to sleep for 1800 seconds.
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...[timerd] using config file /var/tuxbox/config/timerd.conf
OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
08:38:31.972 [sectionsd] DMX::readNbytes received POLLERR, pid 0x12, filter[0] filter 0x4e mask 0xff
08:38:31.975 dmxSDT: going to sleep...
08:38:32.736 eit_set_update_filter, servicekey = 0x4530001445d, current version 4
[yhttpd] Webserver starting...
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
[drive_setup] init drive setup 1.80 
[drive setup] loadDriveSettings: load settings from /var/tuxbox/config/drivesetup.conf
[drive setup] loadFsModulList: can't open directory /var/lib/modules No such file or directory
[drive setup] loadMmcModulList: can't open directory /var/lib/modules No such file or directory
[neutrino] hddtemp  -n -w -q /dev/ide/host0/bus0/target0/lun0/disc > /tmp/hdtemp 2>/dev/null failed with return code = 127
[drive setup] getHddTemp: executing hddtemp  -n -w -q /dev/ide/host0/bus0/target0/lun0/disc > /tmp/hdtemp 2>/dev/null ...failed! hddtemp  not installed
[neutrino] hddtemp  -n -w -q /dev/ide/host0/bus0/target1/lun0/disc > /tmp/hdtemp 2>/dev/null failed with return code = 127
[drive setup] getHddTemp: executing hddtemp  -n -w -q /dev/ide/host0/bus0/target1/lun0/disc > /tmp/hdtemp 2>/dev/null ...failed! hddtemp  not installed
[drive setup] no settings changed!
----------------------------------------------------------------------------------------------------------------------------------------------

DBox & Samsung:

Code: Alles auswählen

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.01.08 08:50:27 =~=~=~=~=~=~=~=~=~=~=~=
ûdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0  mID 01
debug: feID dd    gtxID 0b
debug: fpID 5a     dsID 01-4e.a6.43.07.00.00-e6
debug: HWrev X5  SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug: 
BOOTP/TFTP bootstrap loader (v0.3)
debug: 
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
debug: Got Block #0004
debug: Got Block #0008
debug: Got Block #0012
debug: Got Block #0016
debug: Got Block #0020
debug: Got Block #0024
debug: Got Block #0028
debug: Got Block #0032
debug: Got Block #0036


will verify ELF image, start= 0x800000, size= 173832
verify sig: 262
Branching to 0x40000


U-Boot 2010.03 (Tuxbox) (Jan 02 2011 - 07:21:35)

CPU:   PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
         *** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
       Watchdog enabled
I2C:   ready
DRAM:  32 MB
FLASH:  8 MB
Scanning JFFS2 FS:   .  | / - \ | / - \ |  done.

env: found console with value ttyS0
env: found baudrate with value 9600
env: found dbox_duplex with value 0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
env: found lcd_bias with value 0
FB:    ready
In:    serial
Out:   serial
Err:   serial
Net:   SCC ETHERNET
LCD:   ready

Options:
  1: Console on null
  2: Console on ttyS0
  3: Console on framebuffer
Select option (1-3), other keys to stop autoboot:  1  0 
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 669404 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
   Image Name:   Linux-2.4.37.10-dbox2
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    669340 Bytes = 653.7 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Linux version 2.4.37.10-dbox2 (dietmarw@lalelu.li) (gcc version 3.4.6) #2 Sun Jan 2 07:21:52 CET 2011

On node 0 totalpages: 8192

zone(0): 8192 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex=0

Decrementer Frequency = 252000000/60

m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)

m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)

Console: colour dummy device 80x25

Calibrating delay loop... 66.96 BogoMIPS

Memory: 30828k available (1140k kernel code, 340k data, 60k init, 0k highmem)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.

squashfs: version 3.0 (2006/03/15) Phillip Lougher

i2c-core.o: i2c core module version 2.6.1 (20010830)

i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)

CPM UART driver version 0.04

ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2

pty: 256 Unix98 ptys configured

half-duplex mode enabled

eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1f:9a:7f

loop: loaded (max 8 devices)

D-Box 2 flash driver (size->0x800000 mem->0x10000000)

D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank

 Intel/Sharp Extended Query Table at 0x0035

cfi_cmdset_0001: Erase suspend on write enabled

Creating 6 MTD partitions on "D-Box 2 flash memory":

0x00000000-0x00020000 : "BR bootloader"

0x00020000-0x00040000 : "FLFS (U-Boot)"

0x00040000-0x00580000 : "root (squashfs+lzma)"

0x00580000-0x00800000 : "var (jffs2)"

0x00020000-0x00800000 : "Flash without bootloader"

0x00000000-0x00800000 : "Complete Flash"

Linux video capture interface: v1.00

mice: PS/2 mouse device common for all mice

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 60k init


init started: BusyBox v1.17.3 (2011-01-02 07:23:51 CET)

starting pid 8, tty '': '/etc/init.d/sysinit'
[BOOT] running /etc/init.d/sysinit
Thu Jan  1 01:00:00 UTC 1970

starting pid 22, tty '': '/etc/init.d/rcS'

Please press Enter to activate this console. starting /etc/init.d/S05drivers ...
[BOOT] running /etc/init.d/S05drivers
tuxbox: IDE-Interface detected, Vendor: DboxBaer or kpt.ahab/Stingray

Detected STB:
Vendor: Nokia
Model: D-BOX2  (2 flash chips)
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $

[i2c-8xx]: mpc 8xx i2c init

[i2c-8xx]: adapter: 0

lcd.o: init lcd driver module

lcd.o: found KS0713/SED153X lcd interface

$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $

$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $

DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).

ves1x93: Detected ves1893a rev2

DVB: registering frontend 0:0 (VES1893)...

dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter

$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $

avia_av: $Id: avia_av_core.c,v 1.102 2010/05/25 19:58:20 dbt Exp $

avia_av_core: Starting avia_av_wdt thread.

avia_av: AVIA 500 LB4 found, sptsfix is off

avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $

avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $

avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $

avia_gt_core: autodetecting chip type... GTX

avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $

avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $

avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $

avia_gt_core: masking unhandled irq reg 1 bit 11

avia_gt_core: masking unhandled irq reg 1 bit 13

avia_gt_ucode: loaded ucode vB107

avia_gt_ucode: ucode section filters disabled.

avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...

avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $

avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $

avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $

avia_gt_core: Loaded AViA eNX/GTX driver

avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

Console: switching to colour frame buffer device 82x32

avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device

avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $

avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $

avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $

avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $

avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $

starting /var/etc/init.d/S06hdd ...
/var/etc/init.d/06hdd generated from neutrino ide/mmc/hdd drive-setup
07.01.2011 - 20:33:30
1.80  do not edit!
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4

ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx

dboxide: $Id: main.c,v 1.14 2009/06/19 14:39:26 seife Exp $

ide: late registration of driver.

dboxide: activating cs2

dboxide: address space of IDE-Interface is at: 0xc3b93000

dboxide: IDE-Interface detected, Vendor: DboxBaer or kpt.ahab/Stingray

dboxide: sreset succeeded

Probing IDE interface ide0...

hda: SAMSUNG HM160HC, ATA DISK drive

ide0 at 0x010-0x017,0x04e on irq 47

hda: attached ide-disk driver.

hda: host protected area => 1

hda: lost interrupt

hda: lost interrupt
----------------------------------------------------------------------------------------------------------------------------------------------

Was mir bei den Bootlogs etwas seltsam vorkommt ist die Zuordnung der HDDs als "hda" oder "hdb".
Die Platten sind beide als Master gejumpert und werden jeweils an den identischen Stecker am IDE-Kabel angeschlossen (am Ende).
JtG-Riker
Image-Team
Beiträge: 1015
Registriert: Freitag 7. Februar 2003, 18:37
Kontaktdaten:

Re: Seltsames Phänomen: hda: Lost Interrupt

Beitrag von JtG-Riker »

Entweder das Modemportkabel defekt, nicht richtig gesteckt, oder CPU der dBox defekt.

Schönes Wochenende

Riker
MoonMan

Re: Seltsames Phänomen: hda: Lost Interrupt

Beitrag von MoonMan »

Danke für die Antwort, das war auch der FAQ des Vertreibers zu entnehmen.

Seltsam an dieser Sach ist nur, dass die Barracuda HDD (erster Log) einwandfrei funktioniert (auch die Aufnahme).
Beide 2,5'' HDD das System zum abstürzen bringen. :-?
Kann das auch ein Timing-Problem sein?

Grüsse
MoonMan
Stingray
Erleuchteter
Erleuchteter
Beiträge: 453
Registriert: Mittwoch 27. Juni 2007, 15:25
Kontaktdaten:

Re: Seltsames Phänomen: hda: Lost Interrupt

Beitrag von Stingray »

Handelt es sich um ein IDE-Interface oder um ein IDE-SATA-Interface?
Wurden die Jumpereinstellungen vom SATA-Jumper Master/Slave auf dem IDE-SATA-Interface (falls verbaut) beachtet?
Wenn die IDE-Festplatten als MASTER gejumpert sind dann darf der SATA-Anschluß auf dem Interface NICHT als Master gejumpert sein !!!
Wenn ZWEI IDE-Festplatten an einem IDE-Interface oder IDE-SATA-Interface genutzt werden, dann muß eine IDE-Fesplatte als MASTER und die andere als SLAVE gejumpert werden.
Zudem muß der SATA-Anschluß auf dem IDE-SATA-Interface mit dem SATA-Jumper Enable DEAKTIVIERT werden !!!
MoonMan

Re: Seltsames Phänomen: hda: Lost Interrupt

Beitrag von MoonMan »

@Stingray: Vielen Dank für den kompetenten Support ! :up:

Es funktioniert nun, es war wohl der SATA-Master Jumper.

> Wenn die IDE-Festplatten als MASTER gejumpert sind dann darf der SATA-Anschluß auf dem Interface NICHT als Master gejumpert sein !!!
Das war so direkt leider weder der Einbauanleitung noch der FAQ entnehmen. :-?
Bin, wie beim PC auch, von 2 getrennten Bussen (IDE+SATA) mit unterschiedlichen Controllern ausgegangen.
Antworten