Keine TV-Sender? TPScan gibt folgenden log:

[knilleneu]

Kann mir jemand sagen was ich da tun kann?
Ich habe eine Sagem 2XI Sat Dbox2


[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (10876000 22000000 1)
****************

[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (10861750 22000000 0)
****************

[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (11739000 27500000 1)
****************

[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (11836500 27500000 0)
****************

/var/tuxbox/config/zapit/services.xml: No such file or directory
[sectionsd] DMX: DMX_START: Invalid argument

[rasc]

das komplette Log posten, das kannst Du tun...

[knilleneu]

9Q)5%IQ)5M)5devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:33:93:e9
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.1 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-3d.0b.6a.03.00.00-85
debug: HWrev 01 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0052

will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Aug 5 2002 - 09:06:03)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Sagem
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 634725 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 634661 Bytes = 619 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft ;-) #1 Die Dez 31 18:36:38 CET 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30816k available (1120k kernel code, 372k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:33:93:e9
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu
les/2.4.20/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.20/misc/event.o
event: init ...
Using /lib/modules/2.4.20/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20/misc/dvb_demux.o
Using /lib/modules/2.4.20/misc/dvbdev.o
Using /lib/modules/2.4.20/misc/avia.o
AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $
Using /lib/modules/2.4.20/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 3
Using /lib/modules/2.4.20/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.20/misc/dmxdev.o
Using /lib/modules/2.4.20/misc/dvb_frontend.o
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
Using /lib/modules/2.4.20/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.22 2002/09/13 22:53:55 Jolt Exp $
avia_gt_core: autodetecting chip type... AViA eNX found
avia_gt_enx: $Id: avia_gt_enx.c,v 1.13 2002/09/02 19:25:37 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.6 2002/09/19 21:09:20 Jolt Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.134 2002/09/21 00:00:08 Jolt Exp $
avia_gt_dmx: Successfully loaded ucode VB1.7
ENX-INITed -> 0
there MIGHT be no TS
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.18 2002/09/25 18:50:52 Jolt Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.20/misc/dvb.o
dvb.c: init_dvb
Init VES1993
Using /lib/modules/2.4.20/misc/ves1993.o
i2c-core.o: driver VES1993 DVB DECODER registered.
i2c-core.o: client [VES1993] registered to adapter [](pos. 4).
i2c-core.o: driver sp5659/tsa5059 tuner driver registered.
i2c-core.o: client [DBox2 Tuner Driver] registered to adapter [](pos. 5).
VES1993: sp5659 tuner found
Using /lib/modules/2.4.20/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.130 2002/09/18 15:57:24 Jolt Exp $
avia_gt_napi: hardware section filtering disabled.
Using /lib/modules/2.4.20/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.16 2002/08/22 13:39:33 Jolt Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
Using /lib/modules/2.4.20/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.36 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.20/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.11 2002/09/25 18:50:52 Jolt Exp $
Using /lib/modules/2.4.20/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.4 2002/08/22 13:39:33 Jolt Exp $
cdkVcInfo $Id: cdkVcInfo.c,v 1.1 2002/12/19 16:10:45 alexW Exp $

$Id: sectionsd.cpp,v 1.148 2002/12/09 20:07:52 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
[camd] no card is in slot #2
[camd] a card is in slot #1
$Id: zapit.cpp,v 1.286 2003/01/03 12:41:31 alexw Exp $
[camd] ca system id: 1702
/var/tuxbox/config/zapit/bouquets.xml: No such file or directory
Controld $Id: controld.cpp,v 1.88 2003/01/07 19:08:27 Zwen Exp $

[controld] Boxtype detected: (03, 3, 2, Sagem)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.396 2003/02/02 16:00:56 dirch Exp $

[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
IP : 10.10.10.2
Netmask : 255.255.255.0
Broadcast: 10.10.10.255
Gateway :
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
loading locales: scandir: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[CFrontend::getEvent] FE_FAILURE_EV
zap failed!
[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (10876000 22000000 1)
****************

[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (10861750 22000000 0)
****************

[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (11739000 27500000 1)
****************

[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (11836500 27500000 0)
****************

/var/tuxbox/config/zapit/bouquets.xml: No such file or directory
[sectionsd] DMX: DMX_START: Invalid argument


Kann mir da jemand helfen? Habe schon probiert ne SenderListe einzuspielen,ohne erfolg.

Aber der Sat ist richtig eingestellt.LNB ist in Ordnung....

[rasc]

Mhh, so auf den ersten Blick kann ich nichts erkennen.

Lief die Box mit der Original-BN-Soft?

[knilleneu]

Ja,die lief mir der original Soft und auch schon fast ein Jahr mit Neutrino.Dann hatte ich mal die Schüssel gedreht wegen Skydsl und habe deswegen die Dbox abgebaut.Stand also 3 Monate in der Ecke-dann wieder angeschlossen und nichts geht mehr.
Verstehe ich nicht.Habe die neueste cramfs drauf.
Ach ja, der Sta ist denke ich richtig eingestellt.Denn mein Analoger Receiver findet alle Programme und die auch noch in guter Qualität.
Gleichzeitig habe ich den Rechner mit am Twin LNB- habe auch schon die Anschlüsse vertauscht,aber es bringt nichts.
Da ich SKYDSL nutzen kann denke ich mal das das LNB auch in Ordung ist

P.S.: Satfind zeigt immer:
ber 1656720
snr /0*.+000
sig 0

[knilleneu]

kann mir denn keiner weiterhelfen

[kerlimann]

P.S.: Satfind zeigt immer:
ber 1656720
snr /0*.+000
sig 0

das heisst soviel wie garkein signal. wie, skydsl.. auf welchem satelliten versuchst du denn mit der dbox zu empfangen?

[knilleneu]

Bin auf Astra 19,2° Ost und hatte auch ne andere D-Box dran,die lief sofort - nur ebend diese nicht.

[kerlimann]

ENX-INITed -> 0
there MIGHT be no TS :(
[...]
[CFrontend::getEvent] FE_FAILURE_EV
zap failed!
[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (10876000 22000000 1)
****************

[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (10861750 22000000 0)
****************

[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (11739000 27500000 1)
****************

[CFrontend::getEvent] FE_FAILURE_EV

****************
No signal found on transponder (11836500 27500000 0)
****************

also irgendwie kommt da bei dir nix an. garkein signal. hast du die box mal alleine angeschlossen, ohne die DVB karte? mal betanova aufgespielt, gehts dann? oder beim kollege getestet?

aber, wenn wie du sagst, eine andere box ging.. hmm..

[knilleneu]

Also ja,wie gesagt,die andere Box läuft,die Analogen laufen auch und die DVB-Karte auch,nur diese eine Sagem Box nicht.
Tja mit der BN-Soft ist das auch ein Problem,bekomme immer nur Fehlercode UD1.Also geht auch nicht.

Ich habe da was gelesen,das eventuell der LNBP (was immer das auch ist) kaputt sein könnte.Weiss hier jemand wie man das testen und ggf. reparieren kann?