Standby nach Bootversuch, Hardware defekt?

Beitrag von **robe** » Samstag 26. April 2003, 18:39

Wer kann helfen?

"Nokia dbox2 mit 2xIntel Avia500" für Kabel fiel während des Betriebes mit Betanova aus.
Bild grün, kein Betriebssystem, es hat sich nicht wiederherstellen lassen.

Daraufhin habe ich die dbox vom Händler auf Linux umrüsten lassen.
Sie bootet jetzt mit Linux, startet das Menü ("Booting System" erscheint auf Bildschirm) und lädt z.B. Neutrino, geht aber nach 18 Sek. in den Standbymodus.

Ich habe sie daraufhin mehrfach geflasht, mit alexW2xBaseimages (1.6.9 und 1.6) sowie passenden cdk.cramfs und ucodes. Es funktioniert immer.
Sie bootet aber einfach nicht weiter!

Bedeutet die Meldung:

Initializing...
CPU: PPC823ZTnnA at 67 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: ### No HW ID - assuming TQM8xxL

vielleicht das ein Hardwareproblem vorliegt?

Ich bin dankbar für jeden Tip

Beitrag von **DieMade** » Sonntag 27. April 2003, 13:19

Poste mal das komplette Log. Die Meldung ist übrigens normal.

Beitrag von **robe** » Sonntag 27. April 2003, 14:40

Erst mals Danke, fürs das Interesse, hier das gesamte Logfile:

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-6f.c4.45.07.00.00-fc
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.30, My IP 192.168.0.42
debug: Sending TFTP-request for file C/PROGRAMME/DBOXBOOT/ppcboot_writeflash
will verify ELF image, start= 0x800000, size= 201596
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000

ppcboot 0.6.4 (Apr 11 2002 - 16:10:44)

Initializing...
CPU: PPC823ZTnnA at 67 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-1f-39-3f
FLASH: 8 MB
LCD driver (KS0713) initialized
BOOTP broadcast 1
TFTP from server 192.168.0.30; our IP address is 192.168.0.42
Filename 'C/PROGRAMME/tftpboot/logo-lcd'.
Load address: 0x130000
Loading: ##

LCD logo at: 0x130000 (0x1F9FFC0 bytes)
BOOTP broadcast 1
TFTP from server 192.168.0.30; our IP address is 192.168.0.42
Filename 'C/PROGRAMME/tftpboot/logo-fb'.
Load address: 0x120000
Loading: #########

FB logo at: 0x0 (0x1FC0000 bytes)
AVIA Frambuffer
Input: serial
Output: serial

1: Console on ttyS0
2: Console on null
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
dbox2-ppcboot> bootp 120000 /C/Programme/DBoxBoot/alexW2xBaseimage/alexW2xBaseim
ageV1.6.9.img
BOOTP broadcast 1
TFTP from server 192.168.0.30; our IP address is 192.168.0.42
Filename '/C/Programme/DBoxBoot/alexW2xBaseimage/alexW2xBaseimageV1.6.9.img'.
Load address: 0x120000
Loading: #######################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
#######################################T #######################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
########################

dbox2-ppcboot> protect off 10020000 107fffff
...............................................................
Un-Protected 63 sectors

dbox2-ppcboot> erase 10020000 107fffff
Erase Flash from 0x10020000 to 0x107fffff
sector 66 ....

Erased 63 sectors

dbox2-ppcboot> cp.l 120000 10020000 1F8000
Copy to Flash...

Beitrag von **rasc** » Sonntag 27. April 2003, 15:17

passt doch, die Box ist geflasht.

Wo ist dein Problem? (vielleicht solltest Du das Bootlog posten)

Beitrag von **robe** » Sonntag 27. April 2003, 17:04

Mein Problem ist, dass die dbox nach 18 Sekunden in den Standbymodus geht
und ich so außer dem Bootbild nichts auf dem Fernseher sehen kann.

Hier das Bootlog der dbox:

debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044

will verify ELF image, start= 0x800000, size= 203620
verify sig: 262
Branching to 0x40000

PPCBoot 1.1.6 (TuxBox) (Mar 13 2003 - 12:11:32)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .

.
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 635882 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 635818 Bytes = 620 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Beitrag von **DieMade** » Sonntag 27. April 2003, 17:09

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0

Bevor das kommt, die "2" auf der Tastatur drücken, im Log fehlt das wichtigste.

Beitrag von **robe** » Sonntag 27. April 2003, 17:55

Bin noch Anfänger, hier das komplette Logfile aus der dbox:

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .

.
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 635882 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 635818 Bytes = 620 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Son Apr 13 14:33:10 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30812k available (1120k kernel code, 376k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:1f:39:3f
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 9, console /dev/console: '/etc/init.d/rcS') multi-ca
Using /lib/modules/2.4.20-dbox2/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20-dbox2/misc/info.o
SIOCADDRT: Invalid argument
ifup: Ignoring unknown interface net
ifup: i2c-core.o: driver FOR_PROBE_ONLY registered.
Ignoring unknown interface loopbi2c-core.o: driver unregistered: FOR_PROBE_ONLY
ack
Using /lib/modules/2.4.20-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.20-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20-dbox2/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20-dbox2/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20-dbox2/misc/dvb_demux.o
Using /lib/modules/2.4.20-dbox2/misc/dvbdev.o
Using /lib/modules/2.4.20-dbox2/misc/lcd.o
Using /lib/modules/2.4.20-dbox2/misc/avia.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
avia_core.c: load_dram_image: Microcode verify: 920 errors.
avia_core.c: load_dram_image: Microcode verify: 24359 errors.
avia_core.c: load_imem_image: Imem verify: 256 errors
insmod: init_module: avia: Input/output error
Using /lib/modules/2.4.20-dbox2/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.20-dbox2/misc/dmxdev.o
Using /lib/modules/2.4.20-dbox2/misc/dvb_frontend.o
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
Using /lib/modules/2.4.20-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_set_pcr
Using /lib/modules/2.4.20-dbox2/misc/dvb.o
insmod: unresolved symbol avia_wait
insmod: unresolved symbol avia_wr
insmod: unresolved symbol avia_command
insmod: unresolved symbol avia_rd
insmod: unresolved symbol avia_flush_pcr
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
Init VES1820
Using /lib/modules/2.4.20-dbox2/misc/ves1820.o
insmod: unresolved symbol register_frontend
insmod: unresolved symbol unregister_frontend
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol unregister_demux
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_dmx_release_section_filter
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_fake_queue_irq
insmod: unresolved symbol avia_gt_dmx_get_queue_irq
insmod: unresolved symbol avia_gt_dmx_set_filter_parameter_table
insmod: unresolved symbol register_demux
insmod: unresolved symbol avia_gt_dmx_set_pid_table
insmod: unresolved symbol avia_gt_dmx_force_discontinuity
insmod: unresolved symbol avia_gt_dmx_set_pid_control_table
insmod: unresolved symbol avia_gt_dmx_get_hw_sec_filt_avail
insmod: unresolved symbol avia_gt_dmx_get_queue_info
insmod: unresolved symbol avia_gt_dmx_set_section_filter
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_queue_irq_disable
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_message
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_free_irq
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_vbi.o
insmod: unresolved symbol avia_gt_get_info
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_standby
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.2.1 2003/03/13 15:11:22 alexW Exp $

$Id: sectionsd.cpp,v 1.166 2003/03/14 04:27:55 obi Exp $
caching 504 hours
events are old 60min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[camd] /dev/dvb/card0/ca0: No such file or directory
$Id: zapit.cpp,v 1.290.2.18 2003/03/27 11:04:52 thegoodguy Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
[frontend.cpp:CFrontend:62] /dev/dvb/card0/frontend0: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[zapit] unable to open frontend devices. bye.
[sectionsd] open dmx: No such file or directory
$Id: controld.cpp,v 1.104 2003/03/19 20:59:02 thegoodguy Exp $

[sectionsd] open dmx: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1)
set event: 00000009
[sectionsd] getUTC: open: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] open dmx: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.433 2003/04/01 17:30:24 thegoodguy E
xp $

[sectionsd] getUTC: open: No such file or directory
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[sectionsd] open dmx: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
zapit shot down

Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Going to halt system now ...
Starting pid 118, console /dev/console: '/etc/init.d/halt'
[sectionsd] open dmx: No such file or directory
CXA2092 found
Unmounting 'ramfs' on '/tmp'
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
umount: /tmp: Device or resource busy
Unmounting 'jffs2' on '/var'
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Ready to shutdown system...
The system is going down NOW !![ConfigFile] Unable to open file /var/tuxb[nhttpd
] stop requested......
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for writing.
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
System halt

Beitrag von **Zahni** » Sonntag 27. April 2003, 18:11

Deine Microcodes oder einer Avia ist kaputt.

avia_core.c: load_dram_image: Microcode verify: 920 errors.
avia_core.c: load_dram_image: Microcode verify: 24359 errors.
avia_core.c: load_imem_image: Imem verify: 256 errors

Durch weglassen der ucode.bin kannst Du das testen. Zumindest die sollte dann im Log als erfolgreich geladen auftauchen.

-Zahni

In anbetracht des grünen Bildes würde ich eher auf Hardwaredefekt tippen.

RR4711

Beitrag von **robe** » Sonntag 27. April 2003, 18:54

Hallo,

ich habe mal keine avia eingespielt und das System wolte die avia600 laden, obwohl in der Box auf dem Chip avia500 steht. Im folgenden Bootversuch sind die 500 und 600 vorhanden, aber die ucode.bin fehlt. Außerdem hatte ich schon die cam-alpha für Satanlagen (weil wir Kabel ISH haben) und die für Telekomanlagen erfolglos ausprobiert, aber die sind ja wohl nur für die Premierekarte zuständig.

Hier das Logfile:

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .

.
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 635882 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 635818 Bytes = 620 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Son Apr 13 14:33:10 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30812k available (1120k kernel code, 376k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:1f:39:3f
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 9, console /dev/console: '/etc/init.d/rcS') multi-ca
Using /lib/modules/2.4.20-dbox2/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20-dbox2/misc/info.o
SIOCADDRT: Invalid argument
ifup: Ignoring unknown interface net
ifup: i2c-core.o: driver FOR_PROBE_ONLY registered.
Ignoring unknown interface loopbi2c-core.o: driver unregistered: FOR_PROBE_ONLY
ack
Using /lib/modules/2.4.20-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.20-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20-dbox2/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20-dbox2/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20-dbox2/misc/dvb_demux.o
Using /lib/modules/2.4.20-dbox2/misc/dvbdev.o
Using /lib/modules/2.4.20-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
Using /lib/modules/2.4.20-dbox2/misc/avia.o
AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
avia_core.c: load_dram_image: Microcode verify: 23259 errors.
avia_core.c: load_imem_image: Imem verify: 256 errors
insmod: init_module: avia: Input/output error
Using /lib/modules/2.4.20-dbox2/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.20-dbox2/misc/dmxdev.o
Using /lib/modules/2.4.20-dbox2/misc/dvb_frontend.o
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
Using /lib/modules/2.4.20-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_set_pcr
Using /lib/modules/2.4.20-dbox2/misc/dvb.o
insmod: unresolved symbol avia_wait
insmod: unresolved symbol avia_wr
insmod: unresolved symbol avia_command
insmod: unresolved symbol avia_rd
insmod: unresolved symbol avia_flush_pcr
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
Init VES1820
Using /lib/modules/2.4.20-dbox2/misc/ves1820.o
insmod: unresolved symbol register_frontend
insmod: unresolved symbol unregister_frontend
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol unregister_demux
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_dmx_release_section_filter
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_fake_queue_irq
insmod: unresolved symbol avia_gt_dmx_get_queue_irq
insmod: unresolved symbol avia_gt_dmx_set_filter_parameter_table
insmod: unresolved symbol register_demux
insmod: unresolved symbol avia_gt_dmx_set_pid_table
insmod: unresolved symbol avia_gt_dmx_force_discontinuity
insmod: unresolved symbol avia_gt_dmx_set_pid_control_table
insmod: unresolved symbol avia_gt_dmx_get_hw_sec_filt_avail
insmod: unresolved symbol avia_gt_dmx_get_queue_info
insmod: unresolved symbol avia_gt_dmx_set_section_filter
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_queue_irq_disable
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_message
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_free_irq
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_vbi.o
insmod: unresolved symbol avia_gt_get_info
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_standby
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.2.1 2003/03/13 15:11:22 alexW Exp $

$Id: sectionsd.cpp,v 1.166 2003/03/14 04:27:55 obi Exp $
caching 504 hours
events are old 60min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[camd] /dev/dvb/card0/ca0: No such file or directory
$Id: zapit.cpp,v 1.290.2.18 2003/03/27 11:04:52 thegoodguy Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
[frontend.cpp:CFrontend:62] /dev/dvb/card0/frontend0: No such file or directory
[zapit] unable to open frontend devices. bye.
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
$Id: controld.cpp,v 1.104 2003/03/19 20:59:02 thegoodguy Exp $

[sectionsd] open dmx: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1)
set event: 00000009
[sectionsd] getUTC: open: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] open dmx: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.433 2003/04/01 17:30:24 thegoodguy E
xp $

[sectionsd] open dmx: No such file or directory
[neutrino] frameBuffer Instance created
[sectionsd] getUTC: open: No such file or directory
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
zapit shot down

[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Going to halt system now ...
Starting pid 118, console /dev/console: '/etc/init.d/halt'
CXA2092 found
[sectionsd] open dmx: No such file or directory
Unmounting 'ramfs' on '/tmp'
umount: /tmp: Device or resource busy
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Unmounting 'jffs2' on '/var'
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Ready to shutdown system...
The system is going down NOW !![ConfigFi[ConfigFile] Unable to open file /var/tu
xbox/con[nhttpd] stop requested......
fig/controld.confle] Unable to open file /var/tuxbox/config/controld.conf for wr
iting.
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
System halt

Beitrag von **DieMade** » Sonntag 27. April 2003, 21:47

avia600.ux löschen, avia500.ux & cam-alpha.bin auf die Box laden und nochmal ein Bootlog posten bitte.

Beitrag von **robe** » Montag 28. April 2003, 11:35

Hier das Logfile mit avia500.ux & cam-alpha.bin:

PPCBoot 1.1.6 (TuxBox) (Mar 13 2003 - 12:11:32)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .

.
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 635882 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 635818 Bytes = 620 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Son Apr 13 14:33:10 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30812k available (1120k kernel code, 376k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:1f:39:3f
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 9, console /dev/console: '/etc/init.d/rcS') multi-ca
Using /lib/modules/2.4.20-dbox2/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20-dbox2/misc/info.o
SIOCADDRT: Invalid argument
ifup: Ignoring unknown interface net
ifup: i2c-core.o: driver FOR_PROBE_ONLY registered.
Ignoring unknown interface loopbi2c-core.o: driver unregistered: FOR_PROBE_ONLY
ack
Using /lib/modules/2.4.20-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.20-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20-dbox2/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20-dbox2/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20-dbox2/misc/dvb_demux.o
Using /lib/modules/2.4.20-dbox2/misc/dvbdev.o
Using /lib/modules/2.4.20-dbox2/misc/lcd.o
Using /lib/modules/2.4.20-dbox2/misc/avia.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
avia_core.c: do_firmread: Unable to load '/var/tuxbox/ucodes/avia600.ux'.
insmod: init_module: avia: Input/output error
Using /lib/modules/2.4.20-dbox2/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.20-dbox2/misc/dmxdev.o
Using /lib/modules/2.4.20-dbox2/misc/dvb_frontend.o
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
Using /lib/modules/2.4.20-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_set_pcr
Using /lib/modules/2.4.20-dbox2/misc/dvb.o
insmod: unresolved symbol avia_wait
insmod: unresolved symbol avia_wr
insmod: unresolved symbol avia_command
insmod: unresolved symbol avia_rd
insmod: unresolved symbol avia_flush_pcr
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
Init VES1820
Using /lib/modules/2.4.20-dbox2/misc/ves1820.o
insmod: unresolved symbol register_frontend
insmod: unresolved symbol unregister_frontend
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol unregister_demux
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_dmx_release_section_filter
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_fake_queue_irq
insmod: unresolved symbol avia_gt_dmx_get_queue_irq
insmod: unresolved symbol avia_gt_dmx_set_filter_parameter_table
insmod: unresolved symbol register_demux
insmod: unresolved symbol avia_gt_dmx_set_pid_table
insmod: unresolved symbol avia_gt_dmx_force_discontinuity
insmod: unresolved symbol avia_gt_dmx_set_pid_control_table
insmod: unresolved symbol avia_gt_dmx_get_hw_sec_filt_avail
insmod: unresolved symbol avia_gt_dmx_get_queue_info
insmod: unresolved symbol avia_gt_dmx_set_section_filter
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_queue_irq_disable
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_message
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_free_irq
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_vbi.o
insmod: unresolved symbol avia_gt_get_info
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_standby
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.2.1 2003/03/13 15:11:22 alexW Exp $

$Id: sectionsd.cpp,v 1.166 2003/03/14 04:27:55 obi Exp $
caching 504 hours
events are old 60min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[camd] /dev/dvb/card0/ca0: No such file or directory
$Id: zapit.cpp,v 1.290.2.18 2003/03/27 11:04:52 thegoodguy Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
[frontend.cpp:CFrontend:62] /dev/dvb/card0/frontend0: No such file or directory
[zapit] unable to open frontend devices. bye.
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
$Id: controld.cpp,v 1.104 2003/03/19 20:59:02 thegoodguy Exp $

[ConfigFile] Unabl[sectionsd] open dmx: No such file or directory
e to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1)
set event: 00000009
[sectionsd] getUTC: open: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] open dmx: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.433 2003/04/01 17:30:24 thegoodguy E
xp $
[sectionsd] open dmx: No such file or directory

[sectionsd] getUTC: open: No such file or directory
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
zapit shot down

[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Going to halt system now ...
Starting pid 118, console /dev/console: '/etc/init.d/halt'
CXA2092 found
[sectionsd] open dmx: No such file or directory
Unmounting 'ramfs' on '/tmp'
umount: /tmp: Device or resource busy
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Unmounting 'jffs2' on '/var'
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Ready to shutdown system...
The system is going down NOW !![ConfigFile] Unable to open file /var/[nhttpd] st
op requested......
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for writing.
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
System halt

Beitrag von **Zahni** » Montag 28. April 2003, 11:49

Bitte mal in die Box gucken, was auf den beiden Avia-Chips steht. Kann sein, daß Du eine Box hast, die bisher noch niemand gesehen hat: Nokia Kabel mit Avia 600 /GTX . Probier es nochmal mit avia600.ux. Wichtig: FTP-Programm auf "BINÄR" stellen. Event. andere Ucodes im Netz suchen (ein BN-Image hat Du ja wohl nicht).

-Zahni

Beitrag von **deraaf** » Montag 28. April 2003, 12:48

Zahni hat geschrieben:Kann sein, daß Du eine Box hast, die bisher noch niemand gesehen hat: Nokia Kabel mit Avia 600 /GTX .
-Zahni

Die steht aber bei mir seit Dezember im Wohnzimmer...Nokia Kabel 2*I und BMon1.2 haben m.E. immer Avia 600.

CU
D.R.

Beitrag von **Zahni** » Montag 28. April 2003, 13:42

Nur hat er den BMON 1.0 drauf.

-Zahni

Beitrag von **robe** » Montag 28. April 2003, 16:34

Ich habe die dbox im Dezember 2000 mit einem Premiereabo bekommen und sie bisher nur mit dem Betanovasystem betrieben.
Die vom Händler aus der dbox gelesene Originalsoftware läst sich von der beigefügten CD-ROM aber nicht nutzen
(DBoxII Bootmanger) es kommt nur "File access denied" übrigens auch bei allen alexWs habe die 1.6.9 selbst runtergeladen.

CHIP 1:

C-Cube Microsystems
AVIA 500 TL LB4 Taiwan
0010 CC0225

CHIP 2:

C-Cube AVIA GTX
TL CO Taiwan
0003 CB8091

Möglicherweise waren die Aviadateien schon in der Betanovasoftware beschädigt worden,
die funktionierte ja schließlich auch nicht mehr.

Hier das Logfile mit avia600.ux & cam-alpha.bin ohne ucode.bin:

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .

.
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 635882 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 635818 Bytes = 620 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Son Apr 13 14:33:10 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30812k available (1120k kernel code, 376k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:1f:39:3f
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 9, console /dev/console: '/etc/init.d/rcS') multi-ca
Using /lib/modules/2.4.20-dbox2/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20-dbox2/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
SIOCADDRT: Invalid argument
ifup: i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Ignoring unknown interface net
ifup: Ignoring unknown interface loopback
Using /lib/modules/2.4.20-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.20-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20-dbox2/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20-dbox2/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20-dbox2/misc/dvb_demux.o
Using /lib/modules/2.4.20-dbox2/misc/dvbdev.o
Using /lib/modules/2.4.20-dbox2/misc/avia.o
Using /lib/modules/2.4.20-dbox2/misc/lcd.o
AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
avia_core.c: load_dram_image: Microcode verify: 23271 errors.
avia_core.c: load_imem_image: Imem verify: 256 errors
insmod: init_module: avia: Input/output error
Using /lib/modules/2.4.20-dbox2/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.20-dbox2/misc/dmxdev.o
Using /lib/modules/2.4.20-dbox2/misc/dvb_frontend.o
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
Using /lib/modules/2.4.20-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_set_pcr
Using /lib/modules/2.4.20-dbox2/misc/dvb.o
insmod: unresolved symbol avia_wait
insmod: unresolved symbol avia_wr
insmod: unresolved symbol avia_command
insmod: unresolved symbol avia_rd
insmod: unresolved symbol avia_flush_pcr
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
Init VES1820
Using /lib/modules/2.4.20-dbox2/misc/ves1820.o
insmod: unresolved symbol register_frontend
insmod: unresolved symbol unregister_frontend
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol unregister_demux
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_dmx_release_section_filter
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_fake_queue_irq
insmod: unresolved symbol avia_gt_dmx_get_queue_irq
insmod: unresolved symbol avia_gt_dmx_set_filter_parameter_table
insmod: unresolved symbol register_demux
insmod: unresolved symbol avia_gt_dmx_set_pid_table
insmod: unresolved symbol avia_gt_dmx_force_discontinuity
insmod: unresolved symbol avia_gt_dmx_set_pid_control_table
insmod: unresolved symbol avia_gt_dmx_get_hw_sec_filt_avail
insmod: unresolved symbol avia_gt_dmx_get_queue_info
insmod: unresolved symbol avia_gt_dmx_set_section_filter
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_queue_irq_disable
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_message
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_free_irq
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_vbi.o
insmod: unresolved symbol avia_gt_get_info
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_standby
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.2.1 2003/03/13 15:11:22 alexW Exp $

$Id: sectionsd.cpp,v 1.166 2003/03/14 04:27:55 obi Exp $
caching 504 hours
events are old 60min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[camd] /dev/dvb/card0/ca0: No such file or directory
$Id: zapit.cpp,v 1.290.2.18 2003/03/27 11:04:52 thegoodguy Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
[frontend.cpp:CFrontend:62] /dev/dvb/card0/frontend0: No such file or directory
[zapit] unable to open frontend devices. bye.
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
$Id: controld.cpp,v 1.104 2003/03/19 20:59:02 thegoodguy Exp $

[sectionsd] open dmx: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1)
set event: 00000009
[sectionsd] getUTC: open: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] open dmx: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.433 2003/04/01 17:30:24 thegoodguy E
xp $

[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] open dmx: No such file or directory
zapit shot down

Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Going to halt system now ...
Starting pid 121, console /dev/console: '/etc/init.d/halt'
CXA2092 found
[sectionsd] open dmx: No such file or directory
Unmounting 'ramfs' on '/tmp'
umount: /tmp: Device or resource busy
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Unmounting 'jffs2' on '/var'
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Ready to shutdown system...
The system is going down NOW !![ConfigFi[ConfigFile] Unable to open file /var/tu
xbox/config/controld.conf for writing.
[nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
System halt

Beitrag von **Zahni** » Montag 28. April 2003, 16:58

Also jetzt such erst mal bei Google andere Ucodes.

-Zahni

Beitrag von **DieMade** » Montag 28. April 2003, 17:27

Vor allem, nimm die avia500.ux!

Die Dateien von der CD müssen auf die Festplatte kopiert und der Schreibschutz entfernt werden, dann klappts auch mit den Sicherungen

Beitrag von **robe** » Montag 28. April 2003, 18:33

Es war der Schreibschutz.

Beim Dateien extrahieren mit DBoxII Bootloader erscheint jetzt:

"Das Flash-Image scheint beschädigt zu sein...?!
(Image-Extrationsfehler-Datei"600v" nicht gefunden!)"

Habe eine avia500.ux und avia600.ux zum ausprobieren gefunden.

Beim booten mit avia500.ux erscheint diese Meldung:

AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
avia_core.c: do_firmread: Unable to load '/var/tuxbox/ucodes/avia600.ux'.
insmod: init_module: avia: Input/output error

Beim booten mit avia600.ux erscheint diese Meldung:

AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
avia_core.c: load_dram_image: Microcode verify: 23263 errors.
avia_core.c: load_imem_image: Imem verify: 256 errors
insmod: init_module: avia: Input/output error

Beitrag von **DieMade** » Montag 28. April 2003, 18:46

Ich sag mal, der AVIA ist defekt. Die Treiber erkennen den 500'er nicht als solchen.

Beitrag von **robe** » Montag 28. April 2003, 18:56

Habe avia500.ux in avia600.ux umbenannt, jetzt kommt dies:

AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
avia_core.c: load_dram_image: Microcode verify: 154 errors.
avia_core.c: load_dram_image: Microcode verify: 21417 errors.
avia_core.c: load_imem_image: Imem verify: 92 errors

Was sollte hier eigentlich stehen?

Hallo ?!? Die Hardware ist defekt, deshalb läuft die Box unter Betanova und Linux nicht !

Reparieren lassen !

RR4711

Beitrag von **robe** » Montag 28. April 2003, 19:02

Schade, ich hatte die Hoffnung noch nicht aufgegeben solange ich mit der dbox Kontakt hatte.

So'n AVIA kost net die Welt. Schreib "DieMade" mal ne PM, der macht sowas öfter, oder "kolp", oder wie auch immer sie alle heißen...

RR4711

Beitrag von **robe** » Montag 28. April 2003, 19:08

Danke, werde ich mal machen.