ich bekomme yadd über den Boot-Manager nicht zum laufen.
Das Log-File sieht so aus.
6debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-fe.29.1c.07.00.00-07
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.44.55, My IP 192.168.44.77
debug: Sending TFTP-request for file C/dbox2/yadd/tftpboot/ppcboot
will verify ELF image, start= 0x800000, size= 221437
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
ppcboot 0.6.4 (Jul 15 2001 - 02:25:33)
Initializing...
CPU: PPC823ZTnnB2 at 67 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: xx-xx-xx-xx-xx-xx
FLASH: 8 MB
LCD driver (KS0713) initialized
LCD logo at: none
FB logo at: none
Input: serial
Output: serial
Images:
1: cdk
2: tiab
3: flash
4: test2
Select image (1-4), other keys to stop autoboot: 0
BOOTP broadcast 1
TFTP from server 192.168.44.55; our IP address is 192.168.44.77
Filename 'C/dbox2/yadd/tftpboot/kernel-cdk'.
Load address: 0x100000
Loading: #######################################################################
####################################
## Booting Linux kernel at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 543820 Bytes = 531 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.2 (steffen@sr01.sth-serv.de) (gcc version 3.0.1 20010702 (prer
elease)) #2 Sun Jul 15 02:27:12 CEST 2001
Boot arguments: console=ttyS0 root=/dev/nfs rw nfsroot=192.168.44.55:C/dbox2/ya
dd/cdkroot/
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/nfs rw nfsroot=192.168.44.55:C/dbo
x2/yadd/cdkroot/
time_init: decrementer frequency = 251250000/60
Warning: real time clock seems stuck!
Console: colour dummy device 80x25
Calibrating delay loop... 66.56 BogoMIPS
Memory: 30824k available (980k kernel code, 332k data, 64k init, 0k highmem)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
CPM UART driver version 0.03
devfs: devfs_register(): device already registered: "ttyS"
devfs: devfs_register(): device already registered: "cua"
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
block: queued sectors max/low 20381kB/6793kB, 64 slots per queue
eth0: CPM ENET Version 0.2, xx:xx:xx:xx:xx:xx
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Sending BOOTP requests.... OK
IP-Config: Got BOOTP answer from 192.168.44.55, my address is 192.68.44.77
IP-Config: Guessing netmask 255.255.255.0
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Looking up port of RPC 100003/2 on 192.168.44.55
Looking up port of RPC 100005/2 on 192.168.44.55
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 64k in
Bummer, can't write to log on /dev/tty5!
console=/dev/consoleinit started: BusyBox v0.50 (2001.07.23-21:34+0000) multi-c
all bircS starting
Mounting /proc device
Mounting /dev/pts
Lade emlog
Starting klogd
Starting syslogd
Starting inetd
Setting hostname
Lade module
Lade i2c-core
i2c-core.o: i2c core module
Lade i2c-8xx
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Lade info
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
mID: 01
feID: dd
fpID: 5a
enxID: ffffffff
gtxID: 0b
hwREV: 05
fpREV: 81
DEMOD: VES1893
Lade soundcore
Lade avs
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Lade saa7126
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Lade fp
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Lade avia
Lade gtx_core
gtx-core.c: init_gtx: loaded AViA GTX core driver
Lade demux
Lade cam
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Lade dmxdev
Lade dvbdev
Lade dvb
registering device.
Lade ves1893
i2c-core.o: driver VES1893 DVB DECODER registered.
feID: 1893 dd
i2c-core.o: client [VES1893] registered to adapter [](pos. 4).
sync: 21
vber: 5b20
using QPSK
sync: 20
Lade gtx_dmx
gen_dmx: found gtx
Lade gtx_fb
Console: switching to colour frame buffer device 90x36
Setting up loopback device
starting nstreamzapd
Network Zapper 0.1
starting sectionsd
$Id: sectionsd.cpp,v 1.43 2001/07/26 01:38:35 fnbrd Exp $
caching 120 hours
events are old 60min after their end time
CHCH [DEMUX] START 3
dmxdev: set buffer size 40000 -> 60000
CHCH [DEMUX] START 4
starting controlD
CHCH [DEMUX] START 5
CHCH [DEMUX] STOP 5
CHCH [DEMUX] START 5
Controld 0.1
set volume: 0 ------------------
Lade lcd
Using /lib/modules/2.4.2/misc/lcd.o
lcd.o: LCD driver (KS0713) module
Network LCD-Driver 0.1
[FONT] initializing core...
[FONT] loading fonts...
[FONT] adding font /usr/lib/fonts/Arial.ttf...starting neutrino
OK (Arial/Regular)
[FONT] adding font /usr/lib/fonts/Arial_Bold.ttf...OK (Arial/Bold)
[FONT] adding font /usr/lib/fonts/Arial_Italic.ttf...OK (Arial/Italic)
[FONT] adding font /usr/lib/fonts/Arial_Black.ttf...1024k video mem
neutrino2
Using nstreamzapd
[FONT] initializing core...
[FONT] loading fonts...
[FONT] adding font /usr/lib/fonts/Arial.ttf...OK (Arial Black/Regular)
[FONT] Intializing font cache...
OK (Arial/Regular)
[FONT] adding font /usr/lib/fonts/Arial_Bold.ttf...[FONT] FTC_Face_Requester (Ar
ial/Regular)
OK (Arial/Bold)
[FONT] adding font /usr/lib/fonts/Arial_Italic.ttf...OK (Arial/Italic)
[FONT] adding font /usr/lib/fonts/Arial_Black.ttf...OK (Arial Black/Regular)
[FONT] Intializing font cache...
fbcon_setup: No support for fontwidth 8
fbcon_setup: type 0 (aux 0, depth <IMG SRC="/forum/images/smiles/icon_cool.gif"> not supported
[FONT] FTC_Face_Requester (Arial/Bold)
[FONT] FTC_Face_Requester (Arial Black/Regular)
[FONT] FTC_Face_Requester (Arial/Regular)
[FONT] FTC_Face_Requester (Arial/Italic)
notify: initial
Command received
Version: 1
Command: 3
Param: 1
Param2: 0
Param3: SAT.1
zapping
zapping to: 0, SAT.1
Couldn't get current channel from file /tmp/.dvbs_current
CHCH [DECODER] ABORT
query epg for >SAT.1<
sync: 0
Frequency: 1880000 Symbolrate: 27500000 Voltage: 2 Tone: 0 FEC: 0 DiSEqC: F1
CHCH [DECODER] SETSTREAMTYPE
CHCH [DEMUX] STOP 4
CHCH [DEMUX] START 4
exit epg-get
CHCH [DECODER] PLAY
CHCH [DEMUX] START 0
CHCH [DEMUX] START 1
006 > 6e 50 02 23 09 16
006 > 6e 50 02 23 03 1c
007 < 6f 50 03 23 89 9a 0c
009 < 6f 50 05 23 83 01 17 02 8e
CAID is: 1702
006 > 6e 50 02 23 09 16
007 < 6f 50 03 23 89 12 84
status89: 12
searching EMM-pid for ca_system_ID 1702
CHCH [DEMUX] START 6
query epg for >SAT.1<
CHCH [DEMUX] STOP 4
CHCH [DEMUX] START 4
exit epg-get
query epg for >SAT.1<
CHCH [DEMUX] STOP 4
CHCH [DEMUX] START 4
exit epg-get
query epg for >SAT.1<
CHCH [DEMUX] STOP 4
CHCH [DEMUX] START 4
exit epg-get
query epg for >SAT.1<
CHCH [DEMUX] STOP 4
CHCH [DEMUX] START 4
exit epg-get
query epg for >SAT.1<
CHCH [DEMUX] STOP 4
CHCH [DEMUX] START 4
exit epg-get
read: Connection timed out
EMM-pid found: 0001
012 > 6e 50 08 23 84 01 04 17 02 00 01 80
searching ECM-pid for ca_system_ID 1702
CHCH [DEMUX] START 7
query epg for >SAT.1<
CHCH [DEMUX] STOP 4
CHCH [DEMUX] START 4
exit epg-get
Alles genauso gemacht wie es in den FAQ’s vom Boot-Mannager beschriben steht. Aber scheinbar mache ich noch etwas falsch oder habe etwas überlesen. Wenn ich ein Image in die Box spiele läuft es aber über den Boot-Mannager keine Chance.
Hat jemand eine Idee.
Gruß
LS_2000
