dbox2 kein videosignal
-
alex.dan
- Neugieriger
- Beiträge: 10
- Registriert: Montag 26. März 2007, 01:03
dbox2 kein videosignal
hallo habe eine dbox2 sagem mit 1intel wenn ich die dbox an das fernseher anschließe kriege ich keinen signal wie über scart so wie über rgb kabeln an dem display der dbox wird ganz normal alles angezeigt.woran könnte das liegen was ist kaputt???
-
SoLaLa
- Tuxboxer
- Beiträge: 6119
- Registriert: Mittwoch 3. April 2002, 00:32
-
alex.dan
- Neugieriger
- Beiträge: 10
- Registriert: Montag 26. März 2007, 01:03
ja auf der box ist linux drauf
mein log
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-69.ab.ba.07.00.00-db
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0040
will verify ELF image, start= 0x800000, size= 162920
verify sig: 262
Branching to 0x40000
U-Boot 1.2.0 (Tuxbox) (May 1 2007 - 07:27:43)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ..
.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 669449 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 669385 Bytes = 653.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.34-dbox2 (petze@linux) (gcc version 3.4.4) #2 Di 1. Mai 08:02:
26 CEST 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30824k available (1140k kernel code, 344k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:3b:35:3e
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00540000 : "root (squashfs)"
0x00540000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'lti-call
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Oops: kernel access of bad area, sig: 11
NIP: C00AC984 XER: 00000000 LR: C388E60C SP: C1C85E30 REGS: c1c85d80 TRAP: 0300
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 00000024, DSISR: C0000000
TASK = c1c84000[25] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C388E60C C1C85E30 C1C84000 C38907DC C38907BA 00000007 00000016 C1C3203C
GPR08: 00000000 00000004 0000003F C00AC96C 24008042 100A6A18 00000001 10080000
GPR16: 00000001 100A0000 100ADF50 100ADC90 00009032 C1C85EA0 C1B97000 100BE258
GPR24: C1CAC340 00000003 C3892000 C013B5C8 C3890000 00000007 00000000 00000000
Call backtrace:
C388F3D8 C388E60C C388F9F8 C0010FF8 C000285C 10020E74 10003DA4
10003E20 0FEBC37C 00000000
Segmentation fault
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 1).
Detected STB:
Vendor: Sagem
Model: D-BOX2
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
i2c-core.o: driver DBox2-CAM registered.
i2c-core.o: client [DBox2-CAM] registered to adapter [PowerPC 8xx I2C adapter](p
os. 2).
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
i2c-core.o: client [DVB I2C bridge] registered to adapter [PowerPC 8xx I2C adapt
er](pos. 3).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
DVB: registering frontend 0:0 (Atmel AT76C651A with TUA6010XS)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Starting pid 92, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.237 2007/03/29 15:43:32 mws Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
/var/plugins/operations camdstart
starte camd3
01.01.1970 01:00:04 camd3: BOXTYPE: 1
01.01.1970 01:00:04 camd3: LOG: 2
01.01.1970 01:00:04 camd3: UDP_PORT: 20248
01.01.1970 01:00:04 camd3: original slot au on
01.01.1970 01:00:04 camd3: HTTP_PORT: 9080
01.01.1970 01:00:04 camd3: DNS_CACHE: 600 sec
01.01.1970 01:00:04 camd3: SOCKET: /tmp/camd.sock01
01.01.1970 01:00:04 camd3: KEYS: /var/keys/camd3.keys
01.01.1970 01:00:04 camd3: SERVERS: /var/keys/camd3.servers
01.01.1970 01:00:04 camd3: USERS: /var/keys/camd3.users
avia_gt_ucode: pid 0001 not found
01.01.1970 01:00:04 camd3: UserDB(new): USER=benutzer1 PASS=password2 FROM=any S
ERVICES=any
01.01.1970 01:00:04 camd3: UserDB(new): USER=benutzer110 PASS=password10 FROM=an
y SERVICES=1702:000000:0008:0:0,1722:000000:0008:0:0,
01.01.1970 01:00:04 camd3: original slot: CAID=1702
01.01.1970 01:00:04 camd3: UserDB(update): USER=benutzer110 PASS=password10 FROM
=any SERVICES=1702:000000:0008:0:0,1722:000000:0008:0:0,
01.01.1970 01:00:05 camd3: /var/keys/camd3.keys No such file or directory
01.01.1970 01:00:05 camd3: KeyDB: gestartet
01.01.1970 01:00:05 camd3: camd v3.868 - erfolgreich gestartet
01.01.1970 01:00:05 camd3: HTTP: started on port 9080
$Id: zapit.cpp,v 1.395 2007/03/17 21:34:22 houdini Exp $
[zapit] PMT update enabled
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 4 onid 85
[getservices] dup transponder id 1 onid 85
/tmp/currentservices.xml: No such file or directory
$Id: controld.cpp,v 1.125 2006/09/24 09:17:10 barf Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
[controld] /dev/dbox/avs0: No such file or directory
[controld] /dev/dbox/avs0: No such file or directory
[controld]: ROUTEVIDEO v1 = 0 a1 = 0 v2 = 0 a2 = 0 fblk=1
[controld] /dev/dbox/avs0: No such file or directory
[controld] /dev/dbox/avs0: No such file or directory
[yhttpd] Webserver nhttpd/3.1.3 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[basicsocket] send_data: Resource temporarily unavailable
[yhttpd] Webserver starting...
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[sectionsd] getUTC: read: Connection timed out
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[frontend.cpp:setFrontend:190] ioctl(fd, FE_SET_FRONTEND, feparams): Invalid arg
ument
[neutrino] initialized everything
[frontend.cpp:setFrontend:190] ioctl(fd, FE_SET_FRONTEND, feparams): Invalid arg
ument
zap failed!
mein log
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-69.ab.ba.07.00.00-db
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0040
will verify ELF image, start= 0x800000, size= 162920
verify sig: 262
Branching to 0x40000
U-Boot 1.2.0 (Tuxbox) (May 1 2007 - 07:27:43)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ..
.FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 669449 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 669385 Bytes = 653.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.34-dbox2 (petze@linux) (gcc version 3.4.4) #2 Di 1. Mai 08:02:
26 CEST 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30824k available (1140k kernel code, 344k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:3b:35:3e
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00540000 : "root (squashfs)"
0x00540000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'lti-call
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Oops: kernel access of bad area, sig: 11
NIP: C00AC984 XER: 00000000 LR: C388E60C SP: C1C85E30 REGS: c1c85d80 TRAP: 0300
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 00000024, DSISR: C0000000
TASK = c1c84000[25] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C388E60C C1C85E30 C1C84000 C38907DC C38907BA 00000007 00000016 C1C3203C
GPR08: 00000000 00000004 0000003F C00AC96C 24008042 100A6A18 00000001 10080000
GPR16: 00000001 100A0000 100ADF50 100ADC90 00009032 C1C85EA0 C1B97000 100BE258
GPR24: C1CAC340 00000003 C3892000 C013B5C8 C3890000 00000007 00000000 00000000
Call backtrace:
C388F3D8 C388E60C C388F9F8 C0010FF8 C000285C 10020E74 10003DA4
10003E20 0FEBC37C 00000000
Segmentation fault
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 1).
Detected STB:
Vendor: Sagem
Model: D-BOX2
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
i2c-core.o: driver DBox2-CAM registered.
i2c-core.o: client [DBox2-CAM] registered to adapter [PowerPC 8xx I2C adapter](p
os. 2).
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
i2c-core.o: client [DVB I2C bridge] registered to adapter [PowerPC 8xx I2C adapt
er](pos. 3).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
DVB: registering frontend 0:0 (Atmel AT76C651A with TUA6010XS)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Starting pid 92, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.237 2007/03/29 15:43:32 mws Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
/var/plugins/operations camdstart
starte camd3
01.01.1970 01:00:04 camd3: BOXTYPE: 1
01.01.1970 01:00:04 camd3: LOG: 2
01.01.1970 01:00:04 camd3: UDP_PORT: 20248
01.01.1970 01:00:04 camd3: original slot au on
01.01.1970 01:00:04 camd3: HTTP_PORT: 9080
01.01.1970 01:00:04 camd3: DNS_CACHE: 600 sec
01.01.1970 01:00:04 camd3: SOCKET: /tmp/camd.sock01
01.01.1970 01:00:04 camd3: KEYS: /var/keys/camd3.keys
01.01.1970 01:00:04 camd3: SERVERS: /var/keys/camd3.servers
01.01.1970 01:00:04 camd3: USERS: /var/keys/camd3.users
avia_gt_ucode: pid 0001 not found
01.01.1970 01:00:04 camd3: UserDB(new): USER=benutzer1 PASS=password2 FROM=any S
ERVICES=any
01.01.1970 01:00:04 camd3: UserDB(new): USER=benutzer110 PASS=password10 FROM=an
y SERVICES=1702:000000:0008:0:0,1722:000000:0008:0:0,
01.01.1970 01:00:04 camd3: original slot: CAID=1702
01.01.1970 01:00:04 camd3: UserDB(update): USER=benutzer110 PASS=password10 FROM
=any SERVICES=1702:000000:0008:0:0,1722:000000:0008:0:0,
01.01.1970 01:00:05 camd3: /var/keys/camd3.keys No such file or directory
01.01.1970 01:00:05 camd3: KeyDB: gestartet
01.01.1970 01:00:05 camd3: camd v3.868 - erfolgreich gestartet
01.01.1970 01:00:05 camd3: HTTP: started on port 9080
$Id: zapit.cpp,v 1.395 2007/03/17 21:34:22 houdini Exp $
[zapit] PMT update enabled
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 4 onid 85
[getservices] dup transponder id 1 onid 85
/tmp/currentservices.xml: No such file or directory
$Id: controld.cpp,v 1.125 2006/09/24 09:17:10 barf Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
[controld] /dev/dbox/avs0: No such file or directory
[controld] /dev/dbox/avs0: No such file or directory
[controld]: ROUTEVIDEO v1 = 0 a1 = 0 v2 = 0 a2 = 0 fblk=1
[controld] /dev/dbox/avs0: No such file or directory
[controld] /dev/dbox/avs0: No such file or directory
[yhttpd] Webserver nhttpd/3.1.3 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[basicsocket] send_data: Resource temporarily unavailable
[yhttpd] Webserver starting...
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[sectionsd] getUTC: read: Connection timed out
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[frontend.cpp:setFrontend:190] ioctl(fd, FE_SET_FRONTEND, feparams): Invalid arg
ument
[neutrino] initialized everything
[frontend.cpp:setFrontend:190] ioctl(fd, FE_SET_FRONTEND, feparams): Invalid arg
ument
zap failed!
-
jmittelst
- Tuxboxer
- Beiträge: 6044
- Registriert: Montag 17. November 2003, 06:48
Flash Dir mal ein legales Image, dann klappt das vielleicht sogar schon.
http://wiki.tuxbox-cvs.sourceforge.net/Images
cu
Jens
http://wiki.tuxbox-cvs.sourceforge.net/Images
cu
Jens
-
alex.dan
- Neugieriger
- Beiträge: 10
- Registriert: Montag 26. März 2007, 01:03
-
jmittelst
- Tuxboxer
- Beiträge: 6044
- Registriert: Montag 17. November 2003, 06:48
Gerade, weil Du 0 Ahnung hast, hab ich Dich auf das Wiki verwiesen...
Im Zweifelsfalle halt das aktuelle Yadi oder JtG, jeweils 1xI.
Kabel oder Sat spielt keine Rolle, denn in offiziellen Images werden weder Senderlisten (dafür gibt es die Kanalsuche) noch Ucodes (die sind (C) und müssen aus Deiner originalen Betanova stammen) mitgeliefert.
Das alles und auch Infos dazu steht im Wiki. Links mittig gibt es ein Suchfeld, über das findet man alles wissenswerte zum Thema Tuxbox.
cu
Jens
Im Zweifelsfalle halt das aktuelle Yadi oder JtG, jeweils 1xI.
Kabel oder Sat spielt keine Rolle, denn in offiziellen Images werden weder Senderlisten (dafür gibt es die Kanalsuche) noch Ucodes (die sind (C) und müssen aus Deiner originalen Betanova stammen) mitgeliefert.
Das alles und auch Infos dazu steht im Wiki. Links mittig gibt es ein Suchfeld, über das findet man alles wissenswerte zum Thema Tuxbox.
cu
Jens
-
alex.dan
- Neugieriger
- Beiträge: 10
- Registriert: Montag 26. März 2007, 01:03
habe jetzt eine image draufgemacht alles funktioniert wie ich aus dem lcd display entnehmen konnte aber wenn ich den an tv anschließe scheint es so ob da die ganzen anschlusse hinten tod sind.
mein log jetzt
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:3b:35:3e
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.2.1 (2007.03.17-16:04+0000) multi-call event: $Id: eve
nt.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Oops: kernel access of bad area, sig: 11
NIP: C00B8F7C XER: 00000000 LR: C388E60C SP: C1C9FE30 REGS: c1c9fd80 TRAP: 0300
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 00000024, DSISR: C0000000
TASK = c1c9e000[24] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C388E60C C1C9FE30 C1C9E000 C38907DC C38907BA 00000007 0000001B C1C9E03C
GPR08: 00000000 00000004 0000003F C00B8F64 24008042 10076964 00000001 10050000
GPR16: 10070000 00000001 1007E430 1007E170 00009032 C1C9FEA0 C1BCD000 1008EAC8
GPR24: C1C7F2A0 00000003 C3892000 C01485C8 C3890000 00000007 00000000 00000000
Call backtrace:
C388F3D8 C388E60C C388F9F8 C0010FF8 C000285C 10022980 10003D2C
10003DA8 0FEB80DC 00000000
Segmentation fault
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 1).
Detected STB:
Vendor: Sagem
Model: D-BOX2
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
cam: no firmware file found
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
i2c-core.o: client [DVB I2C bridge] registered to adapter [PowerPC 8xx I2C adapt
er](pos. 2).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Thu Jan 1 01:00:00 CET 1970
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
avia_av_core.c: avia_av_firmware_read: Unable to load '/var/tuxbox/ucodes/avia60
0.ux'.
avia_av: microcode not found, setting up dummy
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters enabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_av_core: Starting avia_gt_wdt thread.
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
DVB: registering frontend 0:0 (Atmel AT76C651A with TUA6010XS)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
$Id: chkIVersion.cpp,v 1.15 2006/07/30 21:23:29 mogway Exp $
Yadi Release vom 17.03.2007 16:00 - Image-Version 2.2.0.0
Networkcfg eth0: 192.168.0.23/255.255.255.0 gw 192.168.0.1 ns
Startmode: Bootmenu - HWS: on
Please press Enter to activate this console. Avia playback mode set to DualPES
[camd] CA_SEND_MSG: No such device
[camd] CA_SEND_MSG: No such device
/bin/enigma: /lib/libpng12.so.0: no version information available (required by /
bin/enigma)
[MOVIEPLAYER] Version 2.1 starting...
enigma, Copyright (C) dbox-Project
enigma comes with ABSOLUTELY NO WARRANTY
This is free software, and you are welcome
to redistribute it under certain conditions.
It is licensed under the GNU General Public License,
Version 2
[eHotplug] created successfully
+ (0) Configuration
reached rl 0
+ (1) Background File Eraser
+ (1) EAUDIO
+ (5) d-Box LCD Hardware
[LCD] set brightness 130, contrast 29
+ (5) eActionMapList
+ (9) GFBDC
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread createted successfully
+ (15) SystemInfo
+ (20) skin subsystem
loading skin: /var/tuxbox/config/enigma/skins/default.esml
loading skin: /share/tuxbox/enigma/skins/default.esml
loading skin: /share/tuxbox/enigma/skins/stone_snr.esml
illegal color "" specified
[FONT] adding font /share/fonts/bluehigh.ttf...OK (Blue.Regular)
[FONT] adding font /share/fonts/bluebold.ttf...OK (Blue.Bold)
[FONT] adding font /share/fonts/pakenham.ttf...OK (lcd)
[FONT] adding font /share/fonts/md_khmurabi_10.ttf...OK (Replacement)
[FONT] adding font /share/fonts/unmrs.pfa...OK (Nimbus)
Font with name lcd already loaded, skip pakenham.ttf
fontalias eStatusBar does exist, skip make alias for font Nimbus
fontalias eChannelInfo does exist, skip make alias for font Nimbus
fontalias eWindow.TitleBar does exist, skip make alias for font Nimbus
fontalias eWindow.Childs does exist, skip make alias for font Nimbus
fontalias eListBox.EntryText.normal does exist, skip make alias for font Nimbus
fontalias eServiceSelector.Entry.Description does exist, skip make alias for fon
t Nimbus
fontalias eServiceSelector.singleColumn.Entry.Name does exist, skip make alias f
or font Nimbus
fontalias eEPGSelector.Entry.Description does exist, skip make alias for font Ni
mbus
fontalias eEPGSelector.Entry.DateTime does exist, skip make alias for font Nimbu
s
fontalias lcd.main.service_name does exist, skip make alias for font Nimbus
fontalias lcd.main.clock does exist, skip make alias for font Nimbus
fontalias lcd.menu.title does exist, skip make alias for font Nimbus
fontalias lcd.menu.element does exist, skip make alias for font Nimbus
fontalias eventview.description does exist, skip make alias for font Nimbus
fontalias eventview.date does exist, skip make alias for font Nimbus
fontalias eventview.time does exist, skip make alias for font Nimbus
fontalias eventview.channel does exist, skip make alias for font Nimbus
Image with name eCheckbox.checked already loaded, skip checked.png
Image with name eCheckbox.unchecked already loaded, skip unchecked.png
Image with name lcd_menu already loaded, skip lcdmenu.png
Image with name lcd_scart already loaded, skip video.png
Image with name mainmenu.background already loaded, skip mainmenu/background-fs8
.png
Image with name sselect_folder already loaded, skip folder-fs8.png
image/img="triaxlogo" - /enigma/pictures/triaxlogo-fs8.png: file not found
image/img="shortcut.escape" - /enigma/pictures/shortcut/escape.png: file not fou
nd
+ (25) eTextInputField
+ (25) RC Input layer
sh: cannot open /share/keymaps/eng.kmap: No such file
load keyboard mapping failed
+ (26) Console RC Driver
+ (26) input device driver
Input device "DBOX-2 FP IR" is not a keyboard.
Found 1 input devices!
+ (30) eGauge
+ (30) eSlider
+ (30) eStatusBar
+ (30) eWindow
+ (30) eWidget
+ (30) eProgress
+ (30) eLabel
+ (30) eCheckbox
+ (30) eButton
+ (30) eChannelInfo
+ (35) textedit field actions
+ (35) number actions
+ (35) cursor actions
+ (35) focus actions
+ (35) list actions
+ (35) shortcut actions
+ (35) enigma standby actions
+ (35) TransponderEditWindow Actions
+ (35) enigma helpwindow actions
+ (35) rotor menu actions
+ (35) enigma vcr actions
+ (35) timer view actions
+ (35) timer edit actions
+ (35) tuxtxt offset actions
+ (35) epg selector actions
+ (35) enigma mainmenu actions
+ (35) EPG Style Selector actions
+ (35) service selector actions
+ (35) enigma main actions
+ (35) enigma global actions
+ (35) enigma event view actions
+ (39) stream watchdog
+ (40) eDVB lib
1 lnbs readed
[eAVSwitch] loading scart-config (scart.conf)
[eAVSwitch] readed scart conf : 2 1 0 0 0 0
[eAVSwitch] readed dvb conf : 0 0 0 0 0 0
[eAVSwitch] setInput 0, avsfd=-1
eDVB::eDVB.
+ (45) eServiceInterface
+ (46) eServiceFileHandler
+ (46) eServiceStructureHandler
+ (47) eServiceHandlerJPG
+ (47) eServicePlaylistHandler
+ (47) eServiceHandlerMP3
+ (47) eServiceHandlerDVB
+ (48) eDVBCAHandler
+ (48) EPG cache
[EPGC] Initialized EPGCache
+ (48) socket mmi handler
[eSocketMMIHandler] created successfully
+ (49) Timer Manager
loading playlist... /var/tuxbox/config/enigma/timer.epl
failed to open.
[eTimerManager] deepstandbywakeup is 0
[eTimerManager] now deepstandbywakeup is 0
FP_IOCTL_CLEAR_WAKEUP_TIMER okay
[eTimerManager] delKey deepstandbywakeup
reached rl 50
[ENIGMA] loading default keymaps...
[eDVB] do nfs/cifs/smbfs mounts
open /dev/dvb/card0/ancillary0 failed(No such file or directory)
lcdMain created: 0x105d9a10
[eZapMain]wasSleeping is 0, wasDeepStandby is 0
no sapi
loading playlist... /hdd/movie/recordings.epl
failed to open.
loading playlist... /var/tuxbox/config/enigma/playlist.epl
failed to open.
loading playlist... /var/tuxbox/config/enigma/userbouquets.tv.epl
loading playlist... /var/tuxbox/config/enigma/userbouquets.file.epl
loading playlist... /var/tuxbox/config/enigma/userbouquets.radio.epl
loading playlist... /var/tuxbox/config/enigma/userbouquet.627cf.tv
loading playlist... /var/tuxbox/config/enigma/userbouquet.a9c85.radio
loading playlist... /var/tuxbox/config/enigma/userbouquet.f2620.file
createService failed!
createService failed!
createService failed!
createService failed!
removeRef on non-existing service!
------------> changed! 0
no transponder 1 44d
[TUNE] tune failed
avia_av: new_audio_config timeout
[ENIGMA_DYN] lockWebIf = 1
[ENIGMA] starting httpd
[NET] httpd server started on port 80
console=ttyS0 detected...disable enigma serial http interface
[ENIGMA_MOUNT] automountMountPoints...
[ENIGMA_MOUNT] automountMountPoints: automount(pid101) - 0
[ENIGMA] ok, beginning mainloop
+ (54) wizard: tv system
+ (55) wizard: language
+ (56) wizard: fpudate
+ (57) wizard: timezone
Dont run Timezone Setup.. timezone is already selected
waitpid: No child processes
+ (58) wizard: scan
reached rl 75
[FONT] creating new font color cache entry ff000000 .. 00ffffff
[FONT] creating new font color cache entry 33294a6b .. 00ffffff
mein log jetzt
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:3b:35:3e
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.2.1 (2007.03.17-16:04+0000) multi-call event: $Id: eve
nt.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Oops: kernel access of bad area, sig: 11
NIP: C00B8F7C XER: 00000000 LR: C388E60C SP: C1C9FE30 REGS: c1c9fd80 TRAP: 0300
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 00000024, DSISR: C0000000
TASK = c1c9e000[24] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C388E60C C1C9FE30 C1C9E000 C38907DC C38907BA 00000007 0000001B C1C9E03C
GPR08: 00000000 00000004 0000003F C00B8F64 24008042 10076964 00000001 10050000
GPR16: 10070000 00000001 1007E430 1007E170 00009032 C1C9FEA0 C1BCD000 1008EAC8
GPR24: C1C7F2A0 00000003 C3892000 C01485C8 C3890000 00000007 00000000 00000000
Call backtrace:
C388F3D8 C388E60C C388F9F8 C0010FF8 C000285C 10022980 10003D2C
10003DA8 0FEB80DC 00000000
Segmentation fault
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 1).
Detected STB:
Vendor: Sagem
Model: D-BOX2
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
cam: no firmware file found
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
i2c-core.o: client [DVB I2C bridge] registered to adapter [PowerPC 8xx I2C adapt
er](pos. 2).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Thu Jan 1 01:00:00 CET 1970
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
avia_av_core.c: avia_av_firmware_read: Unable to load '/var/tuxbox/ucodes/avia60
0.ux'.
avia_av: microcode not found, setting up dummy
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters enabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_av_core: Starting avia_gt_wdt thread.
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
DVB: registering frontend 0:0 (Atmel AT76C651A with TUA6010XS)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
$Id: chkIVersion.cpp,v 1.15 2006/07/30 21:23:29 mogway Exp $
Yadi Release vom 17.03.2007 16:00 - Image-Version 2.2.0.0
Networkcfg eth0: 192.168.0.23/255.255.255.0 gw 192.168.0.1 ns
Startmode: Bootmenu - HWS: on
Please press Enter to activate this console. Avia playback mode set to DualPES
[camd] CA_SEND_MSG: No such device
[camd] CA_SEND_MSG: No such device
/bin/enigma: /lib/libpng12.so.0: no version information available (required by /
bin/enigma)
[MOVIEPLAYER] Version 2.1 starting...
enigma, Copyright (C) dbox-Project
enigma comes with ABSOLUTELY NO WARRANTY
This is free software, and you are welcome
to redistribute it under certain conditions.
It is licensed under the GNU General Public License,
Version 2
[eHotplug] created successfully
+ (0) Configuration
reached rl 0
+ (1) Background File Eraser
+ (1) EAUDIO
+ (5) d-Box LCD Hardware
[LCD] set brightness 130, contrast 29
+ (5) eActionMapList
+ (9) GFBDC
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread createted successfully
+ (15) SystemInfo
+ (20) skin subsystem
loading skin: /var/tuxbox/config/enigma/skins/default.esml
loading skin: /share/tuxbox/enigma/skins/default.esml
loading skin: /share/tuxbox/enigma/skins/stone_snr.esml
illegal color "" specified
[FONT] adding font /share/fonts/bluehigh.ttf...OK (Blue.Regular)
[FONT] adding font /share/fonts/bluebold.ttf...OK (Blue.Bold)
[FONT] adding font /share/fonts/pakenham.ttf...OK (lcd)
[FONT] adding font /share/fonts/md_khmurabi_10.ttf...OK (Replacement)
[FONT] adding font /share/fonts/unmrs.pfa...OK (Nimbus)
Font with name lcd already loaded, skip pakenham.ttf
fontalias eStatusBar does exist, skip make alias for font Nimbus
fontalias eChannelInfo does exist, skip make alias for font Nimbus
fontalias eWindow.TitleBar does exist, skip make alias for font Nimbus
fontalias eWindow.Childs does exist, skip make alias for font Nimbus
fontalias eListBox.EntryText.normal does exist, skip make alias for font Nimbus
fontalias eServiceSelector.Entry.Description does exist, skip make alias for fon
t Nimbus
fontalias eServiceSelector.singleColumn.Entry.Name does exist, skip make alias f
or font Nimbus
fontalias eEPGSelector.Entry.Description does exist, skip make alias for font Ni
mbus
fontalias eEPGSelector.Entry.DateTime does exist, skip make alias for font Nimbu
s
fontalias lcd.main.service_name does exist, skip make alias for font Nimbus
fontalias lcd.main.clock does exist, skip make alias for font Nimbus
fontalias lcd.menu.title does exist, skip make alias for font Nimbus
fontalias lcd.menu.element does exist, skip make alias for font Nimbus
fontalias eventview.description does exist, skip make alias for font Nimbus
fontalias eventview.date does exist, skip make alias for font Nimbus
fontalias eventview.time does exist, skip make alias for font Nimbus
fontalias eventview.channel does exist, skip make alias for font Nimbus
Image with name eCheckbox.checked already loaded, skip checked.png
Image with name eCheckbox.unchecked already loaded, skip unchecked.png
Image with name lcd_menu already loaded, skip lcdmenu.png
Image with name lcd_scart already loaded, skip video.png
Image with name mainmenu.background already loaded, skip mainmenu/background-fs8
.png
Image with name sselect_folder already loaded, skip folder-fs8.png
image/img="triaxlogo" - /enigma/pictures/triaxlogo-fs8.png: file not found
image/img="shortcut.escape" - /enigma/pictures/shortcut/escape.png: file not fou
nd
+ (25) eTextInputField
+ (25) RC Input layer
sh: cannot open /share/keymaps/eng.kmap: No such file
load keyboard mapping failed
+ (26) Console RC Driver
+ (26) input device driver
Input device "DBOX-2 FP IR" is not a keyboard.
Found 1 input devices!
+ (30) eGauge
+ (30) eSlider
+ (30) eStatusBar
+ (30) eWindow
+ (30) eWidget
+ (30) eProgress
+ (30) eLabel
+ (30) eCheckbox
+ (30) eButton
+ (30) eChannelInfo
+ (35) textedit field actions
+ (35) number actions
+ (35) cursor actions
+ (35) focus actions
+ (35) list actions
+ (35) shortcut actions
+ (35) enigma standby actions
+ (35) TransponderEditWindow Actions
+ (35) enigma helpwindow actions
+ (35) rotor menu actions
+ (35) enigma vcr actions
+ (35) timer view actions
+ (35) timer edit actions
+ (35) tuxtxt offset actions
+ (35) epg selector actions
+ (35) enigma mainmenu actions
+ (35) EPG Style Selector actions
+ (35) service selector actions
+ (35) enigma main actions
+ (35) enigma global actions
+ (35) enigma event view actions
+ (39) stream watchdog
+ (40) eDVB lib
1 lnbs readed
[eAVSwitch] loading scart-config (scart.conf)
[eAVSwitch] readed scart conf : 2 1 0 0 0 0
[eAVSwitch] readed dvb conf : 0 0 0 0 0 0
[eAVSwitch] setInput 0, avsfd=-1
eDVB::eDVB
.+ (45) eServiceInterface
+ (46) eServiceFileHandler
+ (46) eServiceStructureHandler
+ (47) eServiceHandlerJPG
+ (47) eServicePlaylistHandler
+ (47) eServiceHandlerMP3
+ (47) eServiceHandlerDVB
+ (48) eDVBCAHandler
+ (48) EPG cache
[EPGC] Initialized EPGCache
+ (48) socket mmi handler
[eSocketMMIHandler] created successfully
+ (49) Timer Manager
loading playlist... /var/tuxbox/config/enigma/timer.epl
failed to open.
[eTimerManager] deepstandbywakeup is 0
[eTimerManager] now deepstandbywakeup is 0
FP_IOCTL_CLEAR_WAKEUP_TIMER okay
[eTimerManager] delKey deepstandbywakeup
reached rl 50
[ENIGMA] loading default keymaps...
[eDVB] do nfs/cifs/smbfs mounts
open /dev/dvb/card0/ancillary0 failed(No such file or directory)
lcdMain created: 0x105d9a10
[eZapMain]wasSleeping is 0, wasDeepStandby is 0
no sapi
loading playlist... /hdd/movie/recordings.epl
failed to open.
loading playlist... /var/tuxbox/config/enigma/playlist.epl
failed to open.
loading playlist... /var/tuxbox/config/enigma/userbouquets.tv.epl
loading playlist... /var/tuxbox/config/enigma/userbouquets.file.epl
loading playlist... /var/tuxbox/config/enigma/userbouquets.radio.epl
loading playlist... /var/tuxbox/config/enigma/userbouquet.627cf.tv
loading playlist... /var/tuxbox/config/enigma/userbouquet.a9c85.radio
loading playlist... /var/tuxbox/config/enigma/userbouquet.f2620.file
createService failed!
createService failed!
createService failed!
createService failed!
removeRef on non-existing service!
------------> changed! 0
no transponder 1 44d
[TUNE] tune failed
avia_av: new_audio_config timeout
[ENIGMA_DYN] lockWebIf = 1
[ENIGMA] starting httpd
[NET] httpd server started on port 80
console=ttyS0 detected...disable enigma serial http interface
[ENIGMA_MOUNT] automountMountPoints...
[ENIGMA_MOUNT] automountMountPoints: automount(pid101) - 0
[ENIGMA] ok, beginning mainloop
+ (54) wizard: tv system
+ (55) wizard: language
+ (56) wizard: fpudate
+ (57) wizard: timezone
Dont run Timezone Setup.. timezone is already selected
waitpid: No child processes
+ (58) wizard: scan
reached rl 75
[FONT] creating new font color cache entry ff000000 .. 00ffffff
[FONT] creating new font color cache entry 33294a6b .. 00ffffff
-
SoLaLa
- Tuxboxer
- Beiträge: 6119
- Registriert: Mittwoch 3. April 2002, 00:32
-
alex.dan
- Neugieriger
- Beiträge: 10
- Registriert: Montag 26. März 2007, 01:03
-
DrStoned
- Tuxboxer
- Beiträge: 2614
- Registriert: Montag 20. Mai 2002, 10:49
- Image: JTG-Image [IDE] Version 2.4.4
- Image: (7025SS) Merlin
-
Gorcon
- Tuxboxer
- Beiträge: 5873
- Registriert: Samstag 23. Februar 2002, 22:46
Code: Alles auswählen
avia_av: microcode not found, setting up dummy Gruß Gorcon
-
T-Nec
- Einsteiger
- Beiträge: 207
- Registriert: Montag 9. Januar 2006, 13:54
Schließt du das aus der Fehlerbeschreibung oder aus dem Log ?....würd ich sagen den CXA hats zerbröselt
Ich habe hier genau so eine Box mit diesem Fehler....
(Sagem 2xI)
Beim Hochfahren kommt nichtmal das Boot-Image am TV...
Code: Alles auswählen
...blahblah alles ok bis hier...
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Oops: kernel access of bad area, sig: 11
NIP: C00D6E50 XER: 00000000 LR: C389560C SP: C1E89E30 REGS: c1e89d80 TRAP: 0300
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 00000024, DSISR: C0000000
TASK = c1e88000[46] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C389560C C1E89E30 C1E88000 C38977DC C38977BA 00000007 0000001B C1E8803C
GPR08: 00000000 00000004 0000003F C00D6E38 24008042 100ACA40 00000001 10080000
GPR16: 00000001 100B0000 100B4D20 100B4A60 00009032 C1E89EA0 C1D01000 100C6410
GPR24: C1EC8880 00000003 C3899000 C01685C8 C3890000 00000007 00000000 00000000
....
pp.s. : Habe mitlerweile festgestell daß der OOPS beim insmod des avs passiert...
-
samtron
- Neugieriger
- Beiträge: 13
- Registriert: Freitag 11. April 2008, 14:13
Re: dbox2 kein videosignal
hallo zusammen
wie kann man solche Chips einbauen oder ausbauen mit welchen Gerät??
z.B Intel Flash TE28F640
http://www.dbox2.com/pi364874479.htm?categoryId=16
vielen Dank
MfG
wie kann man solche Chips einbauen oder ausbauen mit welchen Gerät??
z.B Intel Flash TE28F640
http://www.dbox2.com/pi364874479.htm?categoryId=16
vielen Dank
MfG