Problem mit Senderliste und Fehler bei single_ch (44,1 k/II)

[mister_no_2]

Hallo Leute,

ich habe 2 Probleme mit meiner DBox2 (Nokia Avia600):

1. Die Sender BN und Pink haben alle die gleichen TID, ONID und SID. In dem Bouquet wird nur ein Sender angezeit (Der an erster Stelle in Services.xml steht). Gibt es hier eine Möglichkeit, dass beide angezeigt werden?

<sat name="Eutelsat W2 16.0E" diseqc="2" position="160">
<transponder id="0001" onid="0001" frequency="12538500" inversion="0" symbol_rate="4341000" fec_inner="1" polarization="1">
<channel service_id="0001" name="BN Sat" service_type="01" />
</transponder>
<transponder id="0001" onid="0001" frequency="11178800" inversion="0" symbol_rate="27500000" fec_inner="3" polarization="1">
<channel service_id="0001" name="Pink Plus" service_type="01" />

2. Bei Sendern die mit single_ch (44,1 k/II) senden, ist der Ton nach 1-2 Sekunden weg. Kann sich bitte das jemand angucken? Leider ist im Log nichts zu sehen. Habe in deshalb auch nicht angehängt. Zu testen ist es am besten auf 16° bei dem Sender Top Musik:
<transponder id="00B0" onid="0000" frequency="12519984" inversion="0" symbol_rate="2156000" fec_inner="2" polarization="1">
<channel service_id="0001" name="Top Musik" service_type="01" />

Vielen Dank für die Hilfe im Voraus!

Gruß
mister_no_2

[MTM]

Hallo,
zu 1. : Wenn du die Liste von Hand änderst, so daß einer der beiden eine andere Kombination der Werte hat (die aber auch wiederum einzigartig sein muss), sollten beide angezeigt werden. Afaik dürfte sowas garnicht vorkommen, diese Kombination muss für jeden Sender einzigartig sein, die Sat-Betreiber machen da aber manchmal murks (war früher wohl bei Türksat ähnlich). Insofern verhält sich Neutrino so absolut korrekt.

MfG,
MTM.

[mister_no_2]

Hi,

jetzt konne ich ein ein Log machen:

¿debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-59.ee.82.07.00.00-59
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08

WATCHDOG reset enabled

dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot

boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
debug: Got Block #0004
debug: Got Block #0008
debug: Got Block #0012
debug: Got Block #0016
debug: Got Block #0020
debug: Got Block #0024
debug: Got Block #0028
debug: Got Block #0032
debug: Got Block #0036


will verify ELF image, start= 0x800000, size= 172392
verify sig: 262
Branching to 0x40000


U-Boot 1.3.4 (Tuxbox) (Oct 3 2008 - 20:41:44)

CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB

FLASH: 8 MB
Scanning JFFS2 FS: . | / - \ | . env: found "console"

env: found "baudrate"
env: found "dbox_duplex"
env: found "lcd_inverse"
env: found "lcd_contrast"
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0

3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
...............................................................
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 670728 bytes loaded to 0x100000
## Booting kernel from Legacy Image at 00100000 ...
Image Name: Linux-2.4.37.2-dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 670664 Bytes = 654.9 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37.2-dbox2 (vom Jtg-Team) (gcc version 3.4.6) #2 Di 21. Jul 11:10:08 CEST 2009

On node 0 totalpages: 8192

zone(0): 8192 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex=0

Decrementer Frequency = 251625000/60

m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)

m8xx_wdt: keep-alive trigger installed (PITC: 0x2580)

Console: colour dummy device 80x25

Calibrating delay loop... 66.76 BogoMIPS

Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.

squashfs: version 3.0 (2006/03/15) Phillip Lougher

i2c-core.o: i2c core module version 2.6.1 (20010830)

i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)

CPM UART driver version 0.04

ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2

pty: 256 Unix98 ptys configured

half-duplex mode enabled

eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:43:72:1f

loop: loaded (max 8 devices)

D-Box 2 flash driver (size->0x800000 mem->0x10000000)

D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank

Intel/Sharp Extended Query Table at 0x0035

cfi_cmdset_0001: Erase suspend on write enabled

Creating 6 MTD partitions on "D-Box 2 flash memory":

0x00000000-0x00020000 : "BR bootloader"

0x00020000-0x00040000 : "FLFS (U-Boot)"

0x00040000-0x006a0000 : "root (squashfs+lzma)"

0x006a0000-0x00800000 : "var (jffs2)"

0x00020000-0x00800000 : "Flash without bootloader"

0x00000000-0x00800000 : "Complete Flash"

Linux video capture interface: v1.00

mice: PS/2 mouse device common for all mice

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 60k init


init started: BusyBox v1.14.2 (2009-07-21 11:14:49 CEST)

starting pid 8, tty '': '/etc/init.d/rcS'
Starting the automounter
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $

tuxbox: no IDE-Interface detected

[i2c-8xx]: mpc 8xx i2c init

[i2c-8xx]: adapter: 0

$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $

$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $

DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).

dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter

$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $

avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $

avia_av: AVIA500 sptsfix is off

avia_av_core: Starting avia_av_wdt thread.

avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $

avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $

avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $

avia_gt_core: autodetecting chip type... GTX

avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $

avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $

avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $

avia_gt_core: masking unhandled irq reg 1 bit 11

avia_gt_core: masking unhandled irq reg 1 bit 13

avia_gt_ucode: loaded ucode v0014

avia_gt_ucode: ucode section filters disabled.

avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...

avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $

avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $

avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $

avia_gt_core: Loaded AViA eNX/GTX driver

avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

Console: switching to colour frame buffer device 82x32

avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device

lcd.o: init lcd driver module

lcd.o: found KS0713/SED153X lcd interface

jtginfo $Id: jtginfo.c,v 2.2 2009/02/07 21:51:28 jtgriker Exp $

avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $

avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $

avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $

ves1x93: Detected ves1893a rev2

DVB: registering frontend 0:0 (VES1893)...

avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $

avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $

Thu Jan 1 12:00:00 CET 1970
$Id: sectionsd.cpp,v 1.303 2009/07/08 20:32:17 rhabarber1848 Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
17:40:05.011 [timeThread] Time set via NTP, going to sleep for 1800 seconds.
[timerd] woke up from timer? false!
17:40:06.207 dmxSDT: going to sleep...
$Id: zapit.cpp,v 1.432 2009/07/09 20:54:44 seife Exp $
[frontend] uncommitted_switch_mode 0 auto_fec 0

/tmp/currentservices.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1

[camd] ca system id: 1702
[CVideo::setVideoFormat] output format: 4:3(LB)

[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
neutrino: /lib/libpng12.so.0: no version information available (required by neutrino)
starting /bin/neutrino
[neutrino] frameBuffer Instance created

812k video mem

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...

[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] found esound, adding to mainmenue/personalize
imageinfo: JTG-Image [IDE] (2.3.3)
loading locales: scandir: No such file or directory
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)

[neutrino] setRepeat: delay=50 period=0 use kernel-repeat: no
[neutrino] received 29 sats
[neutrino] registering as event client
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
avia_gt_core: masking unhandled irq reg 0 bit 6

avia_gt_core: masking unhandled irq reg 0 bit 7

SPTS, queue 0 extended.

avia_gt_core: masking unhandled irq reg 1 bit 15

[neutrino] no file /var/tuxbox/config/init.end was found
[neutrino] initialized everything
17:40:27.432 eit_set_update_filter, servicekey = 0x44100012ee3, current version 28
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 16:9)
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
[zapit] tuned frequency does not match request. difference: 16
SPTS, queue 0 extended.

[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (16:9 -> 4:3)
17:41:59.410 eit_set_update_filter, servicekey = 0xb000000001, current version 1


Das Problem ist, dass das Bild kommt, Ton auch, aber nur für eine Sekunde. Danach ist der Ton weg. Wird daraus jemand schlau?

P.S.: Das Video gestreamt auf die HDD geht mit Ton...

Gruß
mister_no

[seife]

Also wenn du aufnimmst und wieder mit dem movieplayer abspielst gehts, nur "live" nicht? Seltsam.

Ansonsten würde ich versuchen den avia-watchdog mal auszumachen, evtl. hilft das ja was (glaube ich aber nicht).

Vermutlich können die Antiquitäten in der dbox nicht so gut mit diesen ungewöhnlichen Datenraten umgehen.
Geht es denn mit der original Betanova-Soft?

[mister_no_2]

Hi,

habe rausgefunden, dass es mit dem Ton klappt, wenn ich den SPTS Modus ausschalte. Das ist allerdings blöd, da ich gerne TS-Streaming mache mit dem JtG.
Gibt es hier eine Möglichkeit, beides zu machen?

Gruß
mister_no