Das Logfile vom Booten
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-65.9e.e0.06.00.00-98
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044
will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Jul 27 2002 - 10:11:47)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 553795 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 553731 Bytes = 540 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19-rc2-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht,
wird bestraft ;-) #1 Son Jul 28 11:49:33 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30904k available (1036k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (
rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:10:fe:8c
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.05.26-17:53+0000) multi-ca[i2c-8xx]: mpc
8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
AVIA: $Id: avia_core.c,v 1.30 2002/05/06 02:18:18 obi Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
write 1 event's ...
write 1 event's ...
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
Lade alternativen avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.20 2002/06/07 14:00:23 tmbinc Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.14 2002/06/07 18:06:03 Jolt Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.91 2002/07/08 15:12:47 wjoost Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: RISC mem map size: 2048
avia_gt_gv: $Id: avia_gt_gv.c,v 1.21 2002/07/21 15:16:22 waldi Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.14 2002/06/07 18:06:03 Jolt Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.20 2002/06/07 18:06:03 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.26 2002/06/07 18:06:03 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.18 2002/06/07 18:06:03 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Init VES1893
i2c-core.o: driver VES1893 DVB demodulator registered.
i2c-core.o: client [VES1893] registered to adapter [](pos. 4).
avia_gt_core: masking unhandled irq reg 0 bit 6
VES1893: attaching VES1893 at 0x10 to adapter
avia_gt_napi: $Id: avia_gt_napi.c,v 1.88 2002/05/07 16:59:19 Jolt Exp $
avia_gt_napi: warning, misaligned queue 0 (is 32a00, size 10000), aligning...
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.15 2002/07/02 09:31:22 LazyT Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.33 2002/07/19 22:59:21 waldi Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 90x36
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
CXA2092 found
CXA2092 found
Network LCD-Driver $Id: lcdd.cpp,v 1.51 2002/07/10 16:29:08 LazyT Exp $
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
$Id: sectionsd.cpp,v 1.126 2002/05/15 10:00:55 dirch Exp $
caching 504 hours
events are old 60min after their end time
[camd] no card is in slot #2
[camd] no card is in slot #1
[sdt.c] read: Connection timed out
[camd] ca system id: 1702
$Id: zapit.cpp,v 1.193 2002/07/22 01:57:19 Homar Exp $
[getservices.cpp] going to parse satellite Astra 19.2E
[zapit] /var/tuxbox/config/zapit/bouquets.xml: No such file or directory
[zapit] channels have been loaded succesfully
Controld $Id: controld.cpp,v 1.58 2002/05/08 16:21:43 McClean Exp $
[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
[controld] Unknown apsectRatio: 0[controld] setting VideoFormat to auto
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.307 2002/07/22 21:08:07 wjoost Exp $
[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
IP : 192.168.100.222
Netmask : 255.255.255.0
Broadcast: 192.168.100.255
Gateway :
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath:
http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
[controld] setting VideoFormat to auto
video notify: videomenu.videoformat
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[CFrontend::getEvent] FE_COMPLETION_EV
[pmt.cpp] descriptor_tag (b): c3
[pmt.cpp] descriptor_tag (b): 6b
[sdt.c] read: Connection timed out
avia_gt_core: masking unhandled irq reg 1 bit 15
avia_core.c: avia_interrupt: Reserved 01.
write 1 event's ...
write event ... free found
write 1 event's ...
write event ... free found
write event ... filter ok
[getMsgAbsoluteTimeout]: EVT_TIMESET - recalculate timeout
2c9a885/3a82fdcbe747b - 3a82fdfa85139/2e9dcbe
[cat.c] read: Connection timed out
.. Danach geht die box normal weiter in farbe. d-box2 ist a Nokia mit 2 mal Intel und Avia500 Chip. Ucodes sind auch drin. Die box ist über RGB an dem 16:9 Sony Fernseher angeschlossen. Habe es auch über S-Video ausprobiert und das gleiche Problem.. Jedes Startbild ist schwarzweis und rauscht.. 
). Was aber auffällig ist - meine Box ist über S-VHS an den Fernseher angeschlossen. Sobald ich die Box an meinen Rechner anschliesse (über Composite TV-in), ist das Bild schön bunt und rauschfrei ?