Hab mal wieder ne Dbox2 sat 2I Avia600LGTX zum reparieren bekommen.
Linux 1.6 lief anscheinend problemlos.
Auf einmal fiel die Box aus und es waren keine Kanäle mehr zu finden.
Jetzt hab ich mal den neuesten Snapshot aufgespielt und finde immer noch keine Kanäle.
Hier gleich mal das Log:
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-1c.22.43.07.00.00-72
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044
will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Jul 27 2002 - 10:11:47)
CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
. LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 575141 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 575077 Bytes = 561 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft #1 Mit Aug 21 17:11:20 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 251625000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Warning: real time clock seems stuck!
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30948k available (1004k kernel code, 356k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:41:17:d4
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.08.18-11:52+0000) multi-ca[i2c-8xx]: mpc
8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
AVIA: $Id: avia_core.c,v 1.31 2002/08/22 13:39:33 Jolt Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
[FONT] initializing core...write 1 event's ...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
avia_gt_core: $Id: avia_gt_core.c,v 1.21 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.16 2002/09/02 20:56:06 Jolt Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.106 2002/09/04 14:26:49 Jolt Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: RISC mem map size: 2048
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.17 2002/08/22 13:39:33 Jolt Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Init VES1893
i2c-core.o: driver VES1893 DVB demodulator registered.
i2c-core.o: client [VES1893] registered to adapter [](pos. 4).
VES1893: attaching VES1893 at 0x10 to adapter
avia_gt_napi: $Id: avia_gt_napi.c,v 1.103 2002/09/04 13:25:01 Jolt Exp $
avia_gt_napi: warning, misaligned queue 0 (is 32a00, size 10000), aligning...
avia_gt_napi: hardware section filtering disabled.
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.16 2002/08/22 13:39:33 Jolt Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.36 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 90x36
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_oss: $Id: avia_gt_oss.c,v 1.8 2002/08/22 13:39:33 Jolt Exp $
CXA2092 found
CXA2092 found
Network LCD-Driver $Id: lcdd.cpp,v 1.54 2002/08/31 22:30:27 obi Exp $
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
[TIMERD]IDS: 0
$Id: sectionsd.cpp,v 1.128 2002/08/27 19:00:45 obi Exp $
caching 504 hours
events are old 60min after their end time
$Id: zapit.cpp,v 1.216 2002/09/04 13:57:39 thegoodguy Exp $
[getservices.cpp] /var/tuxbox/config/zapit/services.xml: No such file or directo
ry
[zapit] error parsing services!
Controld $Id: controld.cpp,v 1.61 2002/08/27 19:00:45 obi Exp $
[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.316 2002/09/04 15:57:12 dirch Exp $
[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
IP : 192.168.0.23
Netmask : 255.255.255.0
Broadcast: 192.168.0.255
Gateway :
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[zapit] set diseqc type 0
[zapit] set diseqc repeats to 0
[zapit] adding Astra 19.2E (diseqc 0)
[CFrontend::setFrontend] freq 1126000
[CFrontend::getEvent] FE_COMPLETION_EV: freq 1126000
[nit.cpp] read: Connection timed out
no new transponder(s) in current nit
[CFrontend::setFrontend] freq 1111750
[CFrontend::getEvent] FE_COMPLETION_EV: freq 1111750
[nit.cpp] read: Connection timed out
no new transponder(s) in current nit
[CFrontend::setFrontend] freq 1139000
[CFrontend::getEvent] FE_FAILURE_EV
****************
No signal found on transponder (11739000 27500000 1)
****************
[CFrontend::setFrontend] freq 1236500
[CFrontend::getEvent] FE_FAILURE_EV
****************
No signal found on transponder (11836500 27500000 0)
****************
[scan.cpp] found 0 transponders and 0 channels
[getservices.cpp] /var/tuxbox/config/zapit/services.xml: No such file or directo
ry
[scan.cpp] Error parsing Services
[getservices.cpp] /var/tuxbox/config/zapit/services.xml: No such file or directo
ry
[sectionsd] DMX: DMX_START: Invalid argument
Vielleicht kann mir ja jemand helfen.Übrigens ucode.bin wird erkannt
und cam-Alpha ist auch vorhanden.
Avia 500: avia500v093
Avia 600: avia600vb017
Ucode:ucode_B107
Cam-Alpha: cam_01_01_005E
Hab schon im Newbie Forum unter Kein TV-Signal gepostet,hat aber niemand geantwortet,deswegen neu aufgemacht.
poste nochmal,vielleicht weiß jemand bescheid
