Brauche etwas HILFE !!!!!(Dbox2-KABEL)

[jokert3]

Also Mein DBOX2 fährt hoch mit image 1.6.3 ,cdk vom 10.10.
zeigt auch an ARD oder irgend einen sender aber kein Bild und Ton
und im Bootmanager unter Com Terminal steht zap failed kann mir jemand HELFEN !!!!!

Ralf

[Brauni]

Schon mal ne Kanalsuche laufen lassen?

[jokert3]

Sendersuchlauf habe ich gemacht , kanal suche erfolgreich abgeschlossen,
Aber beim suche steht unter Transponder nichts und bei servies auch nichts ,
Kanalliste aus den netz

Ralf

[jokert3]

Kann mir keiner bei meinem problem helfen!!!!!!!!!!!!!!

[SoLaLa]

entweder box put, oder....
was spricht denn der menüpunkt "ucodes überprüfen" ?
und laß mal die senderliste ausm netz weg. die ist nur nützlich wenn die box irgendwie n paar sender beim scan überspringt.
und welche box ist das?
wenns ne nokia ist, dann auch mal schaun ob der durchschleifausgang zum TV n normales bild hat oder ob das evt. verrauscht ist.

hab gerad geschaut... ist das die nokia die du im september schonmal hier hattest?---> antennendurchschleifausgang testen
außerdem: mal das komplette log hier posten (aber nicht mit ner fertigen senderliste, sondern vom booten bis zum senderscan)

[jokert3]

Zu den Ucode :ucode_b107 , AVIA 500v110 , AVIA600vb022 ,Cam_01_02_002D.
TV signal duchgeschliefen bild sehr gut

M3debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-d8.e8.3c.07.00.00-9c
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044

will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Aug 5 2002 - 09:06:03)

CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 577057 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 576993 Bytes = 563 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft ;-) #1 Son Sep 22 10:35:10 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30944k available (1008k kernel code, 356k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:42:77:ab
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu
les/2.4.19/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.19/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.19/misc/event.o
event: init ...
Using /lib/modules/2.4.19/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.19/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.19/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.19/misc/dvb_demux.o
Using /lib/modules/2.4.19/misc/dvbdev.o
Using /lib/modules/2.4.19/misc/avia.o
AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $
Using /lib/modules/2.4.19/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
[FONT] initializing core...write 1 event's ...
write 1 event's ...

[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
Using /lib/modules/2.4.19/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.19/misc/dmxdev.o
Using /lib/modules/2.4.19/misc/dvb_frontend.o
Using /lib/modules/2.4.19/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.22 2002/09/13 22:53:55 Jolt Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.17 2002/09/15 18:06:26 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.6 2002/09/19 21:09:20 Jolt Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.134 2002/09/21 00:00:08 Jolt Exp $
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.18 2002/09/25 18:50:52 Jolt Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.19/misc/dvb.o
Init VES1820
Using /lib/modules/2.4.19/misc/ves1820.o
$Id: ves1820.c,v 1.34 2002/10/08 23:18:42 obi Exp $
i2c-core.o: driver VES1820 DVB-C Demodulator registered.
VES1820: attaching VES1820 at 0x10
i2c-core.o: client [VES1820] registered to adapter [](pos. 4).
VES1820: attached to adapter

Using /lib/modules/2.4.19/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.130 2002/09/18 15:57:24 Jolt Exp $
avia_gt_napi: hardware section filtering disabled.
Using /lib/modules/2.4.19/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.16 2002/08/22 13:39:33 Jolt Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
Using /lib/modules/2.4.19/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.36 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.19/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.11 2002/09/25 18:50:52 Jolt Exp $
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.0 2002/09/26 20:48:26 alexW Exp $

Network LCD-Driver $Id: lcdd.cpp,v 1.54 2002/08/31 22:30:27 obi Exp $

[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
[sectionsdclient] connect: No such file or directory
$Id: sectionsd.cpp,v 1.135 2002/10/04 16:31:25 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
$Id: zapit.cpp,v 1.253 2002/10/04 18:25:17 thegoodguy Exp $

[getservices.cpp] going to parse cable Kabelsignal(AUT)
[zapit] LoadServices: success
[zapit] reading Bouquets ........
[zapit] Found 8 bouquets.
[zapit] channels have been loaded succesfully
Controld $Id: controld.cpp,v 1.64 2002/10/05 20:46:20 dirch Exp $

[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.335 2002/10/05 20:46:20 dirch Exp $

[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
IP : 10.10.10.1
Netmask : 255.255.255.0
Broadcast: 10.10.10.255
Gateway :
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
scandir: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[CPlugins] Dir: /lib/tuxbox/plugins/
[CPlugins] 11 plugins found...
[zapit] set diseqc type 0
[zapit] set diseqc repeats to 0
[zapit] adding Telekom/Ish (diseqc 0)
[CFrontend::setFrontend] freq 346000
[CFrontend::getEvent] FE_COMPLETION_EV: freq 346000
[nit.cpp] read: Connection timed out
no new transponder(s) in current nit
[CFrontend::setFrontend] freq 450000
[CFrontend::getEvent] FE_COMPLETION_EV: freq 450000
[nit.cpp] read: Connection timed out
no new transponder(s) in current nit
[CFrontend::setFrontend] freq 458000
[CFrontend::getEvent] timeout

****************
No signal found on transponder (458000 6900000 0)
****************

[scan.cpp] found 0 transponders and 0 channels
[getservices.cpp] going to parse cable Kabelsignal(AUT)
[zapit] LoadServices: success
[zapit] reading Bouquets ........
[zapit] Found 8 bouquets.

Das sagt der Bootmanager

ich würde mich über einwenig hilfe freuen

Ps. Ich habe die Box mit Linux 1.5 gebraucht gekauft
seit update auf 1.6 Probleme

Gruß Ralf

[Tom1069]

Zu den Ucode :ucode_b107 , AVIA 500v110 , AVIA600vb022 ,Cam_01_02_002D.

Heißt die cam-alpha.bin wirklich 002D? Sollte eigentlich auf 005D enden.
Weiß aber nicht ob es daran liegen könnte.

[jokert3]

Die Cam- Alpha: cam_01_02_002D ich weiß nicht ob es daran liegen kann,
ich habe leider keinen anderes File muß ich mal im netz suche

[SoLaLa]

http://cvs.berlios.de/cgi-bin/viewcvs.c ... cvs-markup

die gibts momentan, das sollte schon klappen, und in dem log is auch nicht gerad was auffälliges.

[jokert3]

Die Seite ist ja nicht schlecht , aber was soll ich da mit anfangen????

Da ich auch ein anfänger bin und nicht die ahnung habe

Gruß Ralf