Ich kann ein Image flashen und die Box bootet auch.
Das Startbild ist allerdings die ganze Zeit zu sehen und nachdem
im Display der Box booting steht dauert es noch ca. 10 Sekunden und die
Box schaltet in Deep Standby.
Egal ob ich neu flashe oder die Box nur neu starte es ist immer
derselbe Vorgang läuft bis booting und schaltet automatisch in Deep Standby.
Wäre toll wenn mir jemand helfen könnte.
Grüße Monja
Hier mal das Log vom Booten :
^debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.0 mID 02
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-e2.41.63.08.00.00-63
debug: HWrev 01 FPrev 0.30
debug: B/Ex/Fl(MB) 32/00/08
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/philips-dbox2/kernel/os in Flash-FS
debug: Got Block #0052
will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Jul 27 2002 - 10:11:47)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Phillips
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 553795 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 553731 Bytes = 540 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19-rc2-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht,
wird bestraft ;-) #1 Son Jul 28 11:49:33 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30904k available (1036k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:2d:53:0c
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.05.26-17:53+0000) multi-ca[i2c-8xx]: mpc
8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [STV6412] registered to adapter [](pos. 0).
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
AVIA: $Id: avia_core.c,v 1.30 2002/05/06 02:18:18 obi Exp $
avia_core.c: load_dram_image: Microcode verify: 23749 errors.
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 2
/lib/modules/2.4.19-rc2-dbox2/misc/avia.o: init_module: Input/output error
Hint: insmod errors can be caused by incorrect module parameters, including inva
lid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt.o: unresolved symbol avia_set_pcr
/lib/modules/2.4.19-rc2-dbox2/misc/dvb.o: unresolved symbol avia_wait
/lib/modules/2.4.19-rc2-dbox2/misc/dvb.o: unresolved symbol avia_wr
/lib/modules/2.4.19-rc2-dbox2/misc/dvb.o: unresolved symbol avia_command
/lib/modules/2.4.19-rc2-dbox2/misc/dvb.o: unresolved symbol avia_rd
/lib/modules/2.4.19-rc2-dbox2/misc/dvb.o: unresolved symbol avia_flush_pcr
/lib/modules/2.4.19-rc2-dbox2/misc/dvb.o: unresolved symbol avia_gt_pcm_set_mpeg
_attenuation
/lib/modules/2.4.19-rc2-dbox2/misc/dvb.o: unresolved symbol avia_gt_pcm_set_pcm_
attenuation
Init TDA8044H
/lib/modules/2.4.19-rc2-dbox2/misc/tda8044h.o: unresolved symbol register_fronte
nd
/lib/modules/2.4.19-rc2-dbox2/misc/tda8044h.o: unresolved symbol unregister_fron
tend
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_set_queue
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_set_queue_irq
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol unregister_
demux
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_set_pcr_pid
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_set_queue_write_pointer
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_all
oc_irq
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol register_de
mux
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_force_discontinuity
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol gtx_set_que
ue_pointer
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_get
_info
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_get_queue_write_pointer
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_fre
e_irq
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_vbi.o: unresolved symbol avia_gt_get_
info
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_sh
ow
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_ge
t_clut
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_input_size
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_pos
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_hi
de
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_get_i
nfo
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_size
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_input_mode
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_clut
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_blevel
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_ge
t_info
Network LCD-Driver $Id: lcdd.cpp,v 1.51 2002/07/10 16:29:08 LazyT Exp $
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
$Id: sectionsd.cpp,v 1.126 2002/05/15 10:00:55 dirch Exp $
caching 504 hours
events are old 60min after their end time
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[camd] /dev/dvb/card0/ca0: No such file or directory
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[sectionsd] DMX: DMX_STOP: Bad file descriptor
$Id: zapit.cpp,v 1.193 2002/07/22 01:57:19 Homar Exp $
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[getservices.cpp] going to parse satellite Astra 19.2E
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[zapit] reading Bouquets ........
[zapit] Found 9 bouquets.
[zapit] channels have been loaded succesfully
/dev/ost/frontend0: No such file or directory
[zapit] unable to open frontend devices. bye.
Segmentation fault
Controld $Id: controld.cpp,v 1.58 2002/05/08 16:21:43 McClean Exp $
[controld] Boxtype detected: (02, 2, 3, Philips)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
zapitclient: connect: No such file or directory
zapitclient: connect: No such file or directory
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.307 2002/07/22 21:08:07 wjoost Exp $
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
The system is going down NOW !!
Sending SIGKILL to all processes.httpd] stop requested......
STV6412 found
Sending all processes the TERM signal...
write 1 event's ...
Sending all processes the KILL signal...
Unmounting ramfs
Unmounting jffs2
The system is halted. Press CTRL-ALT-DEL or turn off power
System halt