ich hebe einen Pflegefall von einer Nokia 500 2xI GTX Kabel Bj99.
Die Kiste läuft mit Images Basis >1.4 nicht (Sender nicht...).
Ich habe versucht eine Yadd (29.08) zu booten. Kann mir jemand die folgende konsolenausgabe interpretieren?
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-bd.xxxxxxxxxx
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.1.5, My IP 192.168.1.100
debug: Sending TFTP-request for file C/dvb/dbox2/Streamh/yadd/tftpboot/ppcboot_o
gr
will verify ELF image, start= 0x800000, size= 224356
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
ppcboot 0.6.4 (Jan 10 2002 - 16:35:20)
Initializing...
CPU: PPC823ZTnnA at 67 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-14-65-06
FLASH: 8 MB
LCD driver (KS0713) initialized
LCD logo at: 0x84A7E (0x1E00 bytes)
FB logo at: 0x868A6 (0x770D bytes)
AVIA Frambuffer
Input: serial
Output: serial
Images:
1: cdk
2: yadd
3: debian
4: tiab
5: flash
Select image (1-5), other keys to stop autoboot: 0
BOOTP broadcast 1
TFTP from server 192.168.1.5; our IP address is 192.168.1.100
Filename 'C/dvb/dbox2/Streamh/yadd/tftpboot/kernel-cdk'.
Load address: 0x100000
Loading: #######################################################################
##################################################
## Booting Linux kernel at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 616299 Bytes = 601 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.2 (steffen@sr01.sth-serv.de) (gcc version 3.0.3) #1 Fri Jan 11
00:16:01 CET 2002
Boot arguments: console=ttyS0 root=/dev/nfs rw nfsroot=192.168.1.5:C/dvb/dbox2/S
treamh/yadd/cdkroot/
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/nfs rw nfsroot=192.168.1.5:C/dvb/db
ox2/Streamh/yadd/cdkroot/
time_init: decrementer frequency = 251250000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x3000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.56 BogoMIPS
Memory: 30584k available (1116k kernel code, 432k data, 68k init, 0k highmem)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
block: queued sectors max/low 20218kB/6739kB, 64 slots per queue
loop: enabling 8 loop devices
eth0: CPM ENET Version 0.2, 00:50:9c:14:65:06
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Sending BOOTP requests.... OK
IP-Config: Got BOOTP answer from 192.168.1.5, my address is 192.168.1.100
IP-Config: Guessing netmask 255.255.255.0
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Looking up port of RPC 100003/2 on 192.168.1.5
Looking up port of RPC 100005/2 on 192.168.1.5
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 68k it
kmod: runaway modprobe loop assumed and stopped
kmod: runaway modprobe loop assumed and stopped
kmod: failed to exec /sbin/modprobe -s -k binfmt-0000, errno = 8
kmod: runaway modprobe loop assumed and stopped
kmod: runaway modprobe loop assumed and stopped
kmod: failed to exec /sbin/modprobe -s -k binfmt-0000, errno = 8
kmod: failed to exec /sbin/modprobe -s -k binfmt-0000, errno = 8
kmod: runaway modprobe loop assumed and stopped
kmod: failed to exec /sbin/modprobe -s -k binfmt-0000, errno = 8
kmod: failed to exec /sbin/modprobe -s -k binfmt-0000, errno = 8
kmod: failed to exec /sbin/modprobe -s -k binfmt-0000, errno = 8
usw.
danke und
bis denne
unimog
