cam-alpha.bin defekt

[jrx001]

hallo,

ich hab da ein problem:

wenn ich mit den bootmanager-utils die ucodes uploaden will meint er das die checksum von cam-alpha nicht korrekt ist. auch erneutes extrahieren der ucodes brachte keine besserung.

ich denke, dass die defekte cam-alpha der grund ist warum ich nach dem sendersuchlauf noch immer nichts sehen kann (steht bei "warte auf epg-info...."). uhrzeit funktioniert aber

so.... was kann ich den tun um an eine funktionierende cam-alpha zu kommen (schätz dass das wieder so ein copyright ding ist das man nicht so einfach downloaden kann .....oder?)

bitte um hilfe
jrx

[DieMade]

Ist nixht defekt, der BM kennt die cam-alpha.bin aus der BN2.01 nicht.

Kannste aber trotzdem benutzen.

[jrx001]

hat jemand vielleicht eine idee wo das problem mit den kanälen sonst herkommt?

[DieMade]

Was sagt Neutrino denn beim UCode-Check? (Service - UCodes überprüfen)

[jrx001]

avia 500:
avia 600:
ucode:
cam-alpha:

ausserdem hängt sich die box beim ausschalten auf (vielleicht bin ich nicht geduldig genut aber nach 30 sek. zieh ich immer den stecker)

bei jedem neustart heisst es dann "die neutrino-einstellungen wurden erweitert. die werte werden auf standard gesetzt". gleich danach kommt dann die meldung dass keine kanäle gefunden werden.

[jrx001]

sorry....

avia500: avia500v110
avia600: avia600vb022
ucode: ucode_b107
cam-alpha: cam_01_02_105f

[DieMade]

Sieht ganz gut aus soweit, falls Du Österreicher bist.

Poste mal ein Bootlog von der Box.

[jrx001]

wie kann ich ein bootlog aufzeichnen?

[DieMade]

Nullmodemkabel anhängen.

Im Bootmanager nur COM auf 9600 Baud aktivieren.

Box einschalten.

[Tom1069]

Nullmodem einstecken, Bootmanager Com wählen und auf
9600 stellen. Dann nur Com auswählen und BM starten.
Box starten und los gehts.

[jrx001]

wie kann ich denn das ganze in ne datei ausgeben.

[jrx001]

so....

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-53.33.cb.05.00.00-18
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044

will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Aug 5 2002 - 09:06:03)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 577057 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 576993 Bytes = 563 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft ;-) #1 Son Sep 22 10:35:10 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30944k available (1008k kernel code, 356k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:11:6e:4e
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu
les/2.4.19/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.19/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.19/misc/event.o
event: init ...
Using /lib/modules/2.4.19/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.19/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.19/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.19/misc/dvb_demux.o
Using /lib/modules/2.4.19/misc/dvbdev.o
Using /lib/modules/2.4.19/misc/lcd.o
Using /lib/modules/2.4.19/misc/avia.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
write 1 event's ...
write 1 event's ...
Using /lib/modules/2.4.19/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.19/misc/dmxdev.o
Using /lib/modules/2.4.19/misc/dvb_frontend.o
Using /lib/modules/2.4.19/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.22 2002/09/13 22:53:55 Jolt Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.17 2002/09/15 18:06:26 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.6 2002/09/19 21:09:20 Jolt Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.134 2002/09/21 00:00:08 Jolt Exp $
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.18 2002/09/25 18:50:52 Jolt Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.19/misc/dvb.o
Init VES1893
Using /lib/modules/2.4.19/misc/ves1893.o
i2c-core.o: driver VES1893 DVB demodulator registered.
i2c-core.o: client [VES1893] registered to adapter [](pos. 4).
avia_gt_core: masking unhandled irq reg 0 bit 6
VES1893: attaching VES1893 at 0x10 to adapter
Using /lib/modules/2.4.19/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.130 2002/09/18 15:57:24 Jolt Exp $
avia_gt_napi: hardware section filtering disabled.
Using /lib/modules/2.4.19/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.16 2002/08/22 13:39:33 Jolt Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
Using /lib/modules/2.4.19/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.36 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.19/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.11 2002/09/25 18:50:52 Jolt Exp $
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.0 2002/09/26 20:48:26 alexW Exp $

Network LCD-Driver $Id: lcdd.cpp,v 1.54 2002/08/31 22:30:27 obi Exp $

[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
/var/tuxbox/config/lcdd.conf: No such file or directory
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
[sectionsdclient] connect: No such file or directory
$Id: sectionsd.cpp,v 1.135 2002/10/04 16:31:25 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
[camd] Unknown 1.CMD-Class 03
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] ca system id: 1762
[camd] no card is in slot #2
[camd] a card is in slot #1
$Id: zapit.cpp,v 1.253 2002/10/04 18:25:17 thegoodguy Exp $

/var/tuxbox/config/zapit/zapit.conf: No such file or directory
[zapit] /var/tuxbox/config/zapit/zapit.conf not found
/var/tuxbox/config/zapit/services.xml: No such file or directory
[zapit] error parsing services!
Controld $Id: controld.cpp,v 1.64 2002/10/05 20:46:20 dirch Exp $

[controld] error while loading settings: /var/tuxbox/config/controld.conf
[controld] using defaults
[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
/var/tuxbox/config/nhttpd.conf: No such file or directory
unable to open file [camd] no card is in slot #2
[camd] a card is in slot #1
/var/tuxbox/config/nhttpd.conffor writing.
/var/tuxbox/config/nhttpd.conf: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.335 2002/10/05 20:46:20 dirch Exp $

[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[camd] no card is in slot #2
[camd] a card is in slot #1
[neutrino] enable flash
[neutrino] Software update enabled
/var/tuxbox/config/scan.conf: No such file or directory
[neutrino] error while loading scan-settings, using defaults!
IP : 192.168.10.1
Netmask : 255.255.255.0
Broadcast: 192.168.10.255
Gateway :
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
scandir: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
saveing neutrino scan-config
unable to open file /var/tuxbox/config/scan.conffor writing.
unable to open file /var/tuxbox/config/neutrino.conffor writing.

[DieMade]

unable to open file /var/tuxbox/config/scan.conffor writing.
unable to open file /var/tuxbox/config/neutrino.conffor writing.

Da haben wir es doch. Schau mal nach den Rechten auf dem Verzeichnis/den Dateien.

Bevor wir hier uns aber zu Tode suchen, flash das Image am besten mal neu und zwar von hier: http://dboxupdate.berlios.de

[jrx001]

ja .... jetzt scheints zu gehen .... kanalsuche läuft aber noch

thx alot