DBox schaltet sich automatisch ab

Beitrag von **angara** » Montag 14. Juni 2004, 17:11

habe eine gebrauchte DBOX2 (Nokia, 2x Flash), neuestes yadi image drauf (v. 12.6.), doch leider schaltet sich die box bei jedem neustart von selbst wieder ab. genauer gesagt knapp nach der auswahl der GUI (auswahl egal, resultat immer gleich).

das sagt mir die box beim hoch/runterfahren:

Code: Alles auswählen

...
### FS (jffs2) loading 'vmlinuz' to 0x100000
Scanning JFFS2 FS: . done.
### FS load complete: 610191 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
   Image Name:   dbox2
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    610127 Bytes = 595.8 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Linux version 2.4.25-dbox2 (mogway@yadi.org) (gcc version 3.3.3) #4 Sa Jun 12 23
:21:19 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock3 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30908k available (1032k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:10:a5:a7
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
 Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x000e0000 : "kernel (jffs2)"
0x000e0000-0x006a0000 : "root (squashfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'0) multi-
Using /lib/modules/2.4.25-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.25-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.25-dbox2/misc/avs.o
Using /lib/modules/2.4.25-dbox2/misc/saa7126.o
Detected STB:
  Vendor: Nokia
  Model: D-BOX2 
Using /lib/modules/2.4.25-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.25-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.25-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.25-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.25-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.92 2004/05/31 15:34:34 carjay Exp $
avia_av: microcode verify: 31605 errors.
avia_av: imem verify: 256 errors
avia_av: timeout waiting for decoder init to complete. (a0a0a0a0)
insmod: init_module: avia_av: Input/output error
Using /lib/modules/2.4.25-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_av_set_stc
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.25-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_init
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_oss.o
insmod: unresolved symbol avia_av_set_sample_rate
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_av_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_v4l2.o
insmod: unresolved symbol avia_gt_pig_show
insmod: unresolved symbol avia_gt_pig_set_stack
insmod: unresolved symbol avia_gt_pig_set_size
insmod: unresolved symbol avia_gt_pig_set_pos
insmod: unresolved symbol avia_gt_pig_hide
Using /lib/modules/2.4.25-dbox2/misc/ves1820.o
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
Using /lib/modules/2.4.25-dbox2/misc/ves1x93.o
Using /lib/modules/2.4.25-dbox2/misc/avia_av_napi.o
insmod: unresolved symbol avia_av_stream_type_set
insmod: unresolved symbol avia_av_register_video_event_handler
insmod: unresolved symbol avia_av_set_audio_attenuation
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_av_pid_set
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_play_state_set_video
insmod: unresolved symbol avia_av_unregister_video_event_handler
insmod: unresolved symbol avia_av_get_video_size
insmod: unresolved symbol avia_av_play_state_set_audio
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
insmod: unresolved symbol avia_av_sync_mode_set
insmod: unresolved symbol avia_gt_dmx_queue_nr_get_bytes_free
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_get_ucode_info
insmod: unresolved symbol avia_gt_vbi_start
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol avia_av_napi_decoder_stop
insmod: unresolved symbol avia_gt_dmx_queue_stop
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_framer
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_napi_decoder_start
insmod: unresolved symbol avia_gt_dmx_queue_start
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_enable_framer
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_dmx_get_stc
insmod: unresolved symbol avia_gt_accel_crc32
Using /lib/modules/2.4.25-dbox2/kernel/net/sunrpc/sunrpc.o
Yadi Snapshot vom 12.06.2004 23:06 - Image-Version 1.8.1.2
Networkcfg eth0: 192.168.0.202/255.255.255.0 gw 192.168.0.5
Startmode: Bootmenu - SPTS:off - HWS:off
Using /lib/modules/2.4.25-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/cifs/cifs.o
Starting pid 84, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. [LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
.route: SIOC[ADD|DEL]RT: File exists
Yadi Snapshot vom 12.06.2004 23:06 - Image-Version 1.8.1.2
Networkcfg eth0: 192.168.0.202/255.255.255.0 gw 192.168.0.5
Startmode: Bootmenu - SPTS:off - HWS:off
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
$Id: sectionsd.cpp,v 1.176 2004/04/29 09:11:13 metallica Exp $
caching 504 hours
events are old 180min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[camd] /dev/dvb/adapter0/demux0: No such file or directory
$Id: zapit.cpp,v 1.354 2004/06/10 19:56:12 rasc Exp $
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
/var/tuxbox/config/zapit/services.xml: No such file or directory
[audio.cpp:CAudio:34] /dev/dvb/adapter0/audio0: No such file or directory
[video.cpp:CVideo:33] /dev/dvb/adapter0/video0: No such file or directory
[sectionsd] open dmx: No such file or directory
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld] /dev/dvb/adapter0/video0: No such file or directory
[controld] /dev/dvb/adapter0/video0: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
FBIOGET_FSCREENINFO: Bad file descriptor
[sectionsd] getUTC: open: No such file or directory
[neutrino] Error while setting framebuffer mode
zapit shot down :)
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 9 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 8 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 7 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 6 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Starting pid 196, console /dev/console: '/bin/switch'
[sectionsd] getUTC: open: No such file or directory
CXA2092 found
The system is going down NOW !![nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power

vor allem die zeile mit

Code: Alles auswählen

avia_av: microcode verify: 31605 errors.

stimmt mich nachdenklich ...

hat jemand von euch eine idee? danke!

Beitrag von **KeXXeN** » Montag 14. Juni 2004, 18:04

Da scheint irgendwas mit deinem Image nicht zu stimmen, viele Verzeichnisse oder Dateien fehlen.

Einfach ein komplettimag erneut über den Bootmanager flashen und hoffen das es wieder geht.

Beitrag von **zexma** » Montag 14. Juni 2004, 18:27

ähm, da scheinen mir eher die ucodes defekt zu sein.

microcode verify: 31605 errors.

Beitrag von **Npq** » Montag 14. Juni 2004, 20:07

Nein, "verify error" heißt, daß sie nicht richtig im Avia-RAM angekommen sind. Damit schlägt auch das Laden vom Modul fehlt.

Evtl. leider das Avia-RAM kaputt. DieMade weiß da vielleicht mehr drüber?

Beitrag von **DieMade** » Montag 14. Juni 2004, 20:29

Dem Log nach ist vermutlich beides defekt (AVIA und RAM)

Beitrag von **angara** » Montag 14. Juni 2004, 20:59

danke erstmal für die raschen antworten

!

soweit ich das verstanden hab sind (bin zwar bei computern, netzwerkwerken usw. ganz fit, aber so eine dbox seh ich heute zum erstem mal

), sind diese "ucodes" firmwares, die je nach verwendetem chipsatz von box zu box differieren (ich habe eine nokia mit 2 flashs).

kann leicht sein, dass ich zu meiner box die falschen (=irgendwelche) ucodes dazubekommen hab, aber sonst hab ich keine ...

Beitrag von **angara** » Dienstag 15. Juni 2004, 00:04

ok, also mal angenommen ich _hätte_ einen haufen verschiedenster ucodes herumliegen - wie könnte ich herausfinden welche genau zu meinen chipsätzen passen?

Beitrag von **DieMade** » Dienstag 15. Juni 2004, 09:22

avia500.ux = Firmware für den AVIA500-MPEG Decoder (alte Nokia)
avia600.ux = Firmware für den AVIA500-MPEG Decoder (Nokia, Sagem, Philips)
cam-alpha.bin = Firmware für den SEC-Chip (alle Boxen)
ucode.bin = Firmware für den AVIA GTX (Nokia) / eNX (Philips/Sagem)

Unterschiede gibt es in den Versionsnummern.

An den defekten Chips wird das allerdings nichts ändern.

Beitrag von **angara** » Dienstag 15. Juni 2004, 09:51

hab jetzt folgendes probiert:

neues (release-)yadi, nur avia500 treiber (der ist in meiner box drin): die box fährt hoch, findet kanäle, aber kein bild, kein ton. auszug aus dem bootlog:

avia_av_core.c: avia_av_firmware_read: Unable to load '/var/tuxbox/ucodes/avia600.ux'.
avia_av: microcode not found, setting up dummy

möglich, dass dieses image beide treiber beim booten abfrägt?
auf jeden fall ist mir klar, dass ohne mpegdecoder nix geht.

hab dann den avia600 treiber auch reingespielt (b028), dann passiert wieder folgendes beim booten:

.debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01hare/fonts/14B.pcf.gz...
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-96.a9.e0.06.00.00-66/share/fonts/15B.pcf.gz...OK (Fix15/Bold)
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/16/08t cache...
WATCHDOG reset enabledFONT] FTC_Face_Request
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)ace_Requester (Fix14/Bold)
debug:
debug: Transmitting BOOTP request via broadcastfile or directory
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/o
debug: Got Block #0032

will verify ELF image, start= 0x800000, size= 152952
verify sig: 263
Branching to 0x40000

U-Boot 1.1.1 (TuxBox) (May 28 2004 - 13:03:11)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .

.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (jffs2) loading 'vmlinuz' to 0x100000
Scanning JFFS2 FS: .

.
### FS load complete: 610189 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 610125 Bytes = 595.8 kB
Load Address: 00000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.25-dbox2 (mogway@yadi.org) (gcc version 3.3.3) #8 Mo Mai 31 00
:06:01 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock3 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy devic
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30908k available (1032k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Co
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:10:a5:a7
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x000e0000 : "kernel (jffs2)"
0x000e0000-0x006a0000 : "root (squashfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS') mu
Using /lib/modules/2.4.25-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.25-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.25-dbox2/misc/avs.o
Using /lib/modules/2.4.25-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.25-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.25-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.25-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.25-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.25-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.91 2004/05/17 17:40:31 derget Exp $
avia_av: microcode verify: 31603 errors.
avia_av: imem verify: 256 errors
avia_av: timeout waiting for decoder init to complete. (a0a0a0a0)
insmod: init_module: avia_av: Input/output error
Using /lib/modules/2.4.25-dbox2/misc/avia_gt.o
insmod: unresolved symbol avia_av_set_stc
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.25-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffe
insmod: unresolved symbol avia_gt_ir_queue_pulse/icons/shutdown.raw
insmod: unresolved symbol avia_gt_ir_initor while loading palette: /share/tuxbox/n
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
zapit
insmod: unresolved symbol avia_gt_ir_set_frequency (max. 9 seconds)
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
CXA2092 found
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_oss.otop requested......
insmod: unresolved symbol avia_av_set_sample_ratell processes.
Th
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stopbug: DDF: 67.79 BogoMIPS
insmod: unresolved symbol avia_gt_pcm_set_signedebug: BMon V1.0 mID 01

insmod: unresolved symbol avia_gt_pcm_set_width
dbox2:root> debug:
insmod: unresolved symbol avia_gt_pcm_poll
debug:

insmod: unresolved symbol avia_gt_pcm_set_channels
debug:
insmod: unresolved symbol avia_av_get_sample_rate
boot net failed

Flash-FS b
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuationund Flash-FS superblock version 3.1
insmod: unresolved symbol avia_gt_pcm_get_block_size/kernel/os in Flash-FS
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_v4l2.o

will verify ELF image, star
insmod: unresolved symbol avia_gt_pig_show
verify
Scanning JFFS2 FS: .
insmod: unresolved symbol avia_av_writeoad complete: 610189 bytes loaded to 0x
insmod: unresolved symbol avia_av_pid_set
.......................
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write## Booting image at 00100000 ...
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
Image Type: PowerPC Linux Kernel Image (gzi
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
Data Size: 610125 Bytes = 595.
insmod: unresolved symbol avia_av_play_state_set_videodress: 00000000
Entry Poin
insmod: unresolved symbol avia_av_unregister_video_event_handlerK
Uncompressing Kernel Image ...
insmod: unresolved symbol avia_av_get_video_siz
insmod: unresolved symbol avia_av_new_audio_config
Kernel command line: console=ttyS0 root=/dev/
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
m8xx_wdt: active wdt fo
insmod: unresolved symbol avia_av_sync_mode_set
m8xx_wdt: keep-
insmod: unresolved symbol avia_gt_dmx_queue_nr_get_bytes_free
Console: colour dummy device 80
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_napi.olay loop... 66.96 BogoMIPS
insmod: unresolved symbol avia_gt_dmx_get_ucode_innel cod
Page-cache h
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
Linux
insmod: unresolved symbol avia_av_audio_pts_to_stcd upon Swansea University Computer Society NET3.03
insmod: unresolved symbol avia_gt_dmx_queue_write
Initializing RT netlink socket
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext.12c (20020818) Richard Gooch (rgooch@a
insmod: unresolved symbol avia_gt_dmx_queue_startat 0x0380 is on SMC2 using BRG2
insmod: unresolved symbol avia_gt_get_info
pty: 256 Unix98 ptys configur
insmod: unresolved symbol avia_gt_dmx_enable_framersion 0.2.dbox2 on SCC2, 00:50:9c:10:a5:a7
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video2 flash driver (size->0x800000 mem->0x10000000)
insmod: unresolved symbol avia_gt_dmx_free_queueox 2 flash memory: Found 2 x16 devices at 0x0 in
insmod: unresolved symbol avia_gt_dmx_alloc_queue_

Using word write
Using /lib/modules/2.4.25-dbox2/kernel/net/sunrpc/sunrpc.o"D-Box 2 flash memory":
Yadi Release vom 30.05.2004 23:55 - Image-Version 1.8.1.0
0x00020000-0x00040
Networkcfg eth0: 192.168.0.202/255.255.255.0 gw 192.168.0.100x00040000-0x000e0000 : "kernel (jffs2)"
Using /lib/modules/2.4.25-dbox2/kernel/fs/lockd/lockd.ofs)"
0x006a000
Using /lib/modules/2.4.25-dbox2/kernel/fs/nfs/nfs.o
0x00020000-0x00800000 : "flash withou
Using /lib/modules/2.4.25-dbox2/kernel/fs/cifs/cifs.o
0x00000000-0x00800000 : "complete flash"
Starting pid 84, console /dev/console: '/etc/init.d/start'nterface: v1.00

VFS: Mounted root (squashfs filesystem)
caching 504 hours
events are old 180min after their end timeev
Freeing unused ker
[sectionsd] open dmx: No such file or directory
Starting pid 10, console /dev/consol
[sectionsd] open dmx: No such file or directory

[sectionsd] getUTC: open: No such file or directory

[i2c-8xx]: mpc 8xx i2c init
/var/tuxbox/config/zapit/bouquets.xml: No such file or directoryg /lib/modules/2.4.25-dbox2/misc/dbox2_fp.o
[sectionsd] open dmx: No such file or directory4.25-dbox2/misc/dbox2_fp_input.o
[audio.cpp:CAudio:34] /dev/dvb/adapter0/audio0: No such file or directoryc/avs.o
Using /lib/modules/2.4.
[video.cpp:CVideo:33] /dev/dvb/adapter0/video0: No such file or directorycted STB:
Vendor: Nokia
Model: D-BOX2
$Id: controld.cpp,v 1.117 2004/05/22-dbox2
DVB: registering new adapter (C-Cube
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] open dmx: No such file or directoryB i2c bridge to PowerPC 8xx I2C adapter
[sectionsd] getUTC: open: No such file or directory
Using /lib/modules/2.4.25-dbox2/misc/cam_napi
[sectionsd] open dmx: No such file or directory
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi
[sectionsd] open dmx: No such file or directory
Using /lib/modules/2.4.25-dbox2/misc/
[sectionsd] getUTC: open: No such file or directory

zapit shot down

[sectionsd] getUTC: open: No such file or directorysing /lib/modules/2.4.25-dbox2/misc/avia_gt.o
[sectionsd] open dmx: No such file or directory_core: $Id: avia_gt_core.c,v 1.47 2004/05/23 10
Waiting for controld (max. 9 seconds)
[sectionsd] getUTC: open: No such file or directoryype... GTX
[sectionsd] open dmx: No su
[sectionsd] open dmx: No such file or directory30 05:45:35 obi Exp $
Waiting for controld (max. 8 seconds)
avia_gt_accel: $Id: avia_gt_acce
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory4 2004/05/19 20:15:00 derget Exp $
[sectionsd] open dmx: No such file or directory
avia_gt_core: masking unhandled irq
Waiting for controld (max. 7 seconds)
avia_gt_core:
[sectionsd] getUTC: open: No such file or directory
avia_gt_ucode: load
[sectionsd] open dmx: No such file or directoryavia_gt_ucode: ucode section filters disabled.
[sectionsd] getUTC: open: No such file or directoryt_dmx: warning, misaligned queue 0 (is 0xFD200, siz
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 6 seconds)rq reg 0 b
Waiting for controld (max. 6 seconds)rq reg 0 b
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
Starting pid 172, console /dev/console: '/bin/switch'
CXA2092 found
The system is going down NOW !![nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power

kann ich jetzt also fix davon ausgehen, dass mein avia500-chip hinüber ist? falls ja - macht irgendwas sinn außer die box wegschmeißen

?

danke,
angara.

Beitrag von **DieMade** » Dienstag 15. Juni 2004, 10:17

Dem Log nach ist vermutlich beides defekt (AVIA und RAM)

An dieser Aussage hat sich leider nichts geändert.

Bei den momentanen Preisen für 2'er-DBoxen lohnt sich das wohl nicht wirklich (bei einer Kabelbox erst recht nicht).

Beitrag von **angara** » Dienstag 15. Juni 2004, 11:05

schade... trotzdem danke für deine hilfe

!