also habe ich mir von remote-admin die „yadd Head 30.November 2005, 1314.tar.bz2“ heruntergeladen
Diese funktioniert auch super (unter debian) soweit ich das bis jetzt beurteilen kann
nun wollte ich die yadd unter windows mit dem DboxBootmanager probieren
da gibt es aber nfs Probleme (mit den devfs ?)
mache ich einen Fehler oder gehen die neuen yadds nicht mehr mit dem DboxBootmanager
könnt Ihr euch das mal anschauen
Danke schon mal für Eure Hilfe
An bei die logs
***Adapter Desc: Realtek RTL8029(AS) Ethernet Adapt (via IpHlpApi #0)
***MAC address: xx:xx:xx:xx:xx:xx Local IP: 192.168.0.2
***BootP server started... Port 67
***TFTP server started... Port 69
BootP> Request from 00:50:9C:xx:xx:xx (assuming that this is DBox).
BootP> Created dynamic ARP entry for DBoxIP 192.168.0.5 with MAC 00:50:9C:xx:xx:xx
BootP> Answer sent!
TFTP> Started TFTP-Transfer for "C:\DBoxBoot\tftpboot\u-boot"...
TFTP> Transfer finished, sent 265 blocks
BootP> Created dynamic ARP entry for DBoxIP 192.168.0.5 with MAC 00:50:9C:xx:xx:xx
BootP> Answer sent!
TFTP> Non-BootP TFTP-transfer requested "logo-lcd"
TFTP> Started TFTP-Transfer for "logo-lcd"...
TFTP> Transfer finished, sent 16 blocks
BootP> Created dynamic ARP entry for DBoxIP 192.168.0.5 with MAC 00:50:9C:xx:xx:xx
BootP> Answer sent!
TFTP> Non-BootP TFTP-transfer requested "logo-fb"
TFTP> Started TFTP-Transfer for "logo-fb"...
TFTP> Transfer finished, sent 25 blocks
TFTP> Non-BootP TFTP-transfer requested "kernel-cdk"
TFTP> Started TFTP-Transfer for "kernel-cdk"...
TFTP> Transfer finished, sent 1559 blocks
1 - mountd: mount: path: C/DBoxBoot/cdkroot
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: nfslookup: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
.............und endlos weiter..............
und das log
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID xx-xx.xx.xx.xx.xx.xx-xx
debug: HWrev 21 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.2, My IP 192.168.0.5
debug: Sending TFTP-request for file C/DBoxBoot/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 135620
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.2 (Tuxbox) (Nov 30 2005 - 12:52:54)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'C/DBoxBoot/tftpboot/u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'logo-lcd'.
Load address: 0x100000
Loading: ##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'C/DBoxBoot/tftpboot/u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'logo-fb'.
Load address: 0x100000
Loading: ###
Bytes transferred = 12737 (31c1 hex)
Options:
1: Bootmeldungen auf Seriell (ttyS0) - standard
2: Bootmeldungen auf TV (fb0)
3: Keine Bootmeldungen
4: Flashen via YADD
- Flashimage umbennenn in dboxflash.img
- in das Verzeichniss tftpboot kopieren
- beim Bootvorgang die Taste 4 drcken.
HAVE FUN...
...special u-boot for DboxII Boot-Manager
v 1.1.2 not overclocked - patched by Homar 2003
Select option (1-4), other keys to stop autoboot: 0
Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'kernel-cdk'.
Load address: 0x100000
Loading: #################################################################
#################################################################
##########################
Bytes transferred = 798025 (c2d49 hex)
..............................................................
Un-Protected 62 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 797961 Bytes = 779.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.31-dbox2 (sinnlos98@endlichLinux) (gcc version 3.4.4) #7 Mi No
v 30 12:54:18 CET 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.2:C/DBoxBoot/cdkroot ip=
192.168.0.5:192.168.0.2:::::off console=ttyS0
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2580)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30508k available (1352k kernel code, 440k data, 68k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:xx:xx:xx
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (Cramfs)"
0x006a0000-0x00800000 : "var (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
IP-Config: Guessing netmask 255.255.255.0
IP-Config: Complete:
device=eth0, addr=192.168.0.5, mask=255.255.255.0, gw=255.255.255.255,
host=192.168.0.5, domain=, nis-domain=(none),
bootserver=192.168.0.2, rootserver=192.168.0.2, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 192.168.0.2
Looking up port of RPC 100005/1 on 192.168.0.2
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 68k init
init started: BusyBox v1.01 (2005.11.26-14:29+0000) multi-call bmodprobe: Can't
locate module tuxbox
/proc/bus/tuxbox/vendor: No such file or directory
/proc/bus/tuxbox/vendor: No such file or directory
/proc/bus/tuxbox/model: No such file or directory
/proc/bus/tuxbox/model: No such file or directory
/proc/bus/tuxbox/submodel: No such file or directory
/proc/bus/tuxbox/submodel: No such file or directory
Detected STB:
Vendor: Unknown
Model: Unknown Unknown
ln: /dev/dvb/adapter0/demux1: No such file or directory
ln: /dev/dvb/adapter0/dvr1: No such file or directory
Loading /share/keymaps/i386/qwertz/de-latin1.kmap.gz
loadkeys: /share/keymaps/i386/qwertz/de-latin1.kmap.gz:8: cannot open include fi
le qwertz-layout
Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.207 2005/11/27 12:21:15 rasc Exp $
caching 504 hours
events are old 180min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[camd] /dev/dvb/adapter0/ca0: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
$Id: zapit.cpp,v 1.384 2005/11/28 05:19:39 metallica Exp $
[frontend.cpp:CFrontend:50] /dev/dvb/adapter0/frontend0: No such file or directo
ry
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[getservices.cpp:FindTransponder:210] going to parse dvb-s provider Astra 19.2E
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[zapit.cpp:prepare_channels:914] LoadServices: success
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[bouquets.cpp:parseBouquetsXml:366] reading bouquets
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[bouquets.cpp:parseBouquetsXml:398] found 163 bouquets
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
.............und endlos weiter..............
und hier das debian log, da geht alles
das ist das selbe image das ich auch unter windows probiert habe.
ich habe es auch noch einmal .tar gepackt und unter windows entpackt.
(nicht winrar oder so was) und die symlinks habe ich mit einem hexeditor überprüft.
Connecting to /dev/ttyS0, speed 9600
Escape character: Ctrl-\ (ASCII 28, FS): enabled
Type the escape character followed by C to get back,
or followed by ? to see other options.
----------------------------------------------------
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID xx-xx.xx.xx.xx.xx.xx-xx
debug: HWrev 21 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.2, My IP 192.168.0.5
debug: Sending TFTP-request for file /yadd/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 135620
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.2 (Tuxbox) (Nov 30 2005 - 12:52:54)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename '/yadd/tftpboot/u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'logo-lcd'.
Load address: 0x100000
Loading: ##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename '/yadd/tftpboot/u-boot'.
Load address: 0x100000
Loading: Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'logo-fb'.
Load address: 0x100000
Loading: ###
Bytes transferred = 12737 (31c1 hex)
Options:
1: Bootmeldungen auf Seriell (ttyS0) - standard
2: Bootmeldungen auf TV (fb0)
3: Keine Bootmeldungen
4: Flashen via YADD
- Flashimage umbennenn in dboxflash.img
- in das Verzeichniss tftpboot kopieren
- beim Bootvorgang die Taste 4 drücken.
HAVE FUN...
...special u-boot for DboxII Boot-Manager
v 1.1.2 not overclocked - patched by Homar 2003
Select option (1-4), other keys to stop autoboot: 0
Using SCC ETHERNET device
TFTP from server 192.168.0.2; our IP address is 192.168.0.5
Filename 'kernel-cdk'.
Load address: 0x100000
Loading: #################################################################
#################################################################
##########################
Bytes transferred = 798025 (c2d49 hex)
..............................................................
Un-Protected 62 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 797961 Bytes = 779.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.31-dbox2 (sinnlos98@endlichLinux) (gcc version 3.4.4) #7 Mi Nov 30 12:54:18 CET 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.2:/yadd/cdkroot ip=192.168.0.5:192.168.0.2::255.255.255.0:::off console=ttyS0
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2580)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30508k available (1352k kernel code, 440k data, 68k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9C:xx:xx:xx
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (Cramfs)"
0x006a0000-0x00800000 : "var (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
IP-Config: Complete:
device=eth0, addr=192.168.0.5, mask=255.255.255.0, gw=255.255.255.255,
host=192.168.0.5, domain=, nis-domain=(none),
bootserver=192.168.0.2, rootserver=192.168.0.2, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 192.168.0.2
Looking up port of RPC 100005/1 on 192.168.0.2
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 68k init
init started: BusyBox v1.01 (2005.11.26-14:29+0000) multi-call bDetected STB:
Vendor: Sagem
Model: D-BOX2
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters enabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_av_core: Starting avia_gt_wdt thread.
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
DVB: registering frontend 0:0 (VES1993)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Loading /share/keymaps/i386/qwertz/de-latin1.kmap.gz
loadkeys: /share/keymaps/i386/qwertz/de-latin1.kmap.gz:8: cannot open include file qwertz-layout
Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.207 2005/11/27 12:21:15 rasc Exp $
caching 504 hours
events are old 180min after their end time
[camd] ca system id: 1722
$Id: zapit.cpp,v 1.384 2005/11/28 05:19:39 metallica Exp $
[camd] no card is in slot #2
[camd] no card is in slot #1
[getservices.cpp:FindTransponder:210] going to parse dvb-s provider Astra 19.2E
[zapit.cpp:prepare_channels:914] LoadServices: success
[bouquets.cpp:parseBouquetsXml:366] reading bouquets
[bouquets.cpp:parseBouquetsXml:398] found 163 bouquets
[zapit.cpp:main:2319] channels have been loaded succesfully
[frontend.cpp:setDiseqcType:371] NO_DISEQC
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...
failed: 1
[LCDFONT] Intializing font cache...
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[sectionsd] getUTC: read: Connection timed out
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[basicsocket] send_data: Resource temporarily unavailable
/dev/input/event1: No such file or directory
[neutrino] menue setup
MovieBrowser 0.11, 23 Nov 2005
[ConfigFile] Unable to open file /var/tuxbox/config/moviebrowser.conf for reading.
CMovieBrowser::loadSettings failed
[ConfigFile] Unable to open file /.version for reading.
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[frontend.cpp:secSetTone:292] 28 msec
[frontend.cpp:secSetVoltage:304] 26 msec
[frontend.cpp:secSetTone:292] 39 msec
[neutrino] initialized everything
[frontend.cpp:getEvent:226] FE_HAS_LOCK: freq 1587500
PES, queue 0 normal.
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3)
[timeThread] time(): 03.03.2006 23:49:11, tim: Fri Mar 3 23:49:11 2006
[timeThread] time(): 03.03.2006 23:49:41, tim: Fri Mar 3 23:49:41 2006