Problem beim Image flashen!

Hallo Leute!

Ich habe ein Problem beim Flashen!
Ich bekomme folgenden LOG:
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: LCD init error -1
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.136.3, My IP 192.168.136.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140336
verify sig: 263
boot net: boot file has no valid signature
Branching to 0x40000

U-Boot 1.1.2 (Tuxbox) (Jun 12 2005 - 13:44:14)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 16 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename '/tftpboot/logo-lcd'.
Load address: 0x100000
Loading: *##

Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename '/tftpboot/logo-fb'.
Load address: 0x100000
Loading: *####################################

Bytes transferred = 179877 (2bea5 hex)

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0

Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit

Size: 8192 kB in 71 Sectors

Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
####################

Bytes transferred = 763552 (ba6a0 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 763488 Bytes = 745.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
<0>Rebooting in 180 seconds..ï¿¾ï¿¾debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: LCD init error -1
debug: WATCHDOG RESET
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.136.3, My IP 192.168.136.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140336
verify sig: 263
boot net: boot file has no valid signature
Branching to 0x40000

U-Boot 1.1.2 (Tuxbox) (Jun 12 2005 - 13:44:14)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 16 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename '/tftpboot/logo-lcd'.
Load address: 0x100000
Loading: *##

Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename '/tftpboot/logo-fb'.
Load address: 0x100000
Loading: *####################################

Bytes transferred = 179877 (2bea5 hex)

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0

Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit

Size: 8192 kB in 71 Sectors

Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
####################

Bytes transferred = 763552 (ba6a0 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 763488 Bytes = 745.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
<0>Rebooting in 180 seconds..ï¿¾ï¿¾debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: LCD init error -1
debug: WATCHDOG RESET
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 16/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.136.3, My IP 192.168.136.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140336
verify sig: 263
boot net: boot file has no valid signature
Branching to 0x40000

U-Boot 1.1.2 (Tuxbox) (Jun 12 2005 - 13:44:14)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 16 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename '/tftpboot/logo-lcd'.
Load address: 0x100000
Loading: *##

Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename '/tftpboot/logo-fb'.
Load address: 0x100000
Loading: *####################################

Bytes transferred = 179877 (2bea5 hex)

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0

Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit

Size: 8192 kB in 71 Sectors

Using SCC ETHERNET device
TFTP from server 192.168.136.3; our IP address is 192.168.136.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
####################

Bytes transferred = 763552 (ba6a0 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 763488 Bytes = 745.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Looking up port of RPC 100005/1 on 192.168.136.3

------ Zusatzinformationen ------
Gewählter Netzwerkadapter: 3Com 3C900B-COMBO-Ethernetadapter (Standard) - Paketplaner-Miniport (0)
IP-Adresse des Netzwerkadapters: 192.168.136.3
IP-Adresse die die dbox bekommt: 192.168.136.202
Comport: Kommunikationsanschluss (COM1)
Betriebssystem: Microsoft Windows XP Professional Service Pack 2 (Build 2600)
CPU 1: AMD Athlon(tm) 64 Processor 3200+ @ 2000 MHz
Dateiname des Images: JTG_231205_2X_AVIA500_SAT.img
Imagetyp: Zwei Flashs
DBOX-IFA Version: 2.2
------ Powered by http://www.dboxservice-hallenberg.de ------

Ausser, das die Box nur 16MB hat, sehe ich an dem Log nix wirklich ungewöhnliches.

cu
Jens

Beitrag von **wolgade** » Montag 27. November 2006, 10:30

Code: Alles auswählen

debug: LCD init error -1

Das sieht nicht gut aus. In einem anderen Thread wurde bei der Fehlermeldung über einen defekten Frontprozessor spekuliert. Vielleicht weiß das einer unserer Hardwaredoktoren genauer.

Beitrag von **DieMade** » Montag 27. November 2006, 10:53

Da die Box komplett abstürzt (WATCHDOG RESET), würde ich eher von einer defekten CPU ausgehen.

Möchte auch das IDE Interface einbauen, gibt es mit der Box Probleme?

Wie viel bringt denn eine neue Grafikkarte im PC, wenn die CPU defekt ist?

Deine Box ist kaputt, durch Hardwareerweiterungen beseitigst Du nicht das Ursprungsproblem.

So, habe jetzt das TtG 2.2.2 geflashed bekommen.
Funktioniert auch alles.

Dann müsste auch die CPU heile sein, oder?

Nur wenn ich die Kanalsuche starte, dann bricht er nach ca. 2Sekunden mit der Meldung "Kanalsuche fehlgeschlagen" ab.

Woran kann das liegen?

Habe danach die Services.xml per ftp aufgespielt, danach klappts.

Aber wie bekomm ich das mit der Kanalsuche in Griff?