Nokia Kabel "Kanal zur zeit nicht verfügbar" aber ......

[GAT81]

Nokia Kabel "Kanal zur zeit nicht verfügbar" aber ...... wenn ich eine Kanalsuche machen möchte habe ich ein SAT Menü sprich Astra Einstellungen und nicht wie ich es brauche Kabel Deutschland....

Was kann das sein?

[MTM]

Hallo,
das könnte auf einen Hardwaredefekt hindeuten, wenn der Tuner vom Treiber nicht als Kabelversion erkannt wird, wird von einem Sattuner ausgegangen, deshalb die falsche Anzeige beim Sendersuchlauf etc.

Ein Bootlog könnte da mehr Klarheit schaffen.

MfG,
MTM.

[rhabarber1848]

Tritt der Fehler nach einem Boxneustart auch noch auf?
Wenn nein, ist zapit abgestürzt.

[GAT81]

mhhh also ein Neustart bring auch nichts ...

einen bootlog kann ich leider nicht machen da ich keine serielle schnittstelle mehr habe...

verstehe ich richtig, das die box den tuner als Sat-Tuner erkennt wenn dieser kaputt ist?
also brauche ich wohl einen neuen Tuner oder wie ?

[rhabarber1848]

einen bootlog kann ich leider nicht machen da ich keine serielle schnittstelle mehr habe...

http://www.reichelt.de/?ACTION=3;ARTICL ... ROVID=2402

verstehe ich richtig, das die box den tuner als Sat-Tuner erkennt wenn dieser kaputt ist?

Wenn die Software den Tuner-Typ nicht identifizieren kann,
wird ein Sat-Tuner angenommen.
Ohne Bootlog sind weitere Aussagen Kaffeesatzleserei

[GAT81]

Hier ist der Bootlog

will verify ELF image, start= 0x800000, size= 170736
verify sig: 262
Branching to 0x40000


U-Boot 2009.08 (Tuxbox) (Nov 12 2009 - 15:56:00)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ............... .
env: found console with value ttyS0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
LCD: ready

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (jffs2) loading 'vmlinuz' to 0x200000
### FS load complete: 507325 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
Image Name: Linux-2.4.37.6-dbox2
Image Type: PowerPC Linux Kernel Image (lzma compressed)
Data Size: 507261 Bytes = 495.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37.6-dbox2 (FlatTV@devel) (gcc version 3.4.6) #40 Do 12. Nov 1
6:16:13 CET 2009
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rw rootfstype=jffs2 console=ttyS0,9600
dbox_duplex=
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30832k available (1140k kernel code, 336k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:19:21:46
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00800000 : "root (jffs2+lzma)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.14.4 (2009-11-12 15:57:48 CET)
starting pid 9, tty '': '/etc/init.d/rcS'
mount: using /etc/fstab
udhcpc (v1.14.4) started
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
tuxbox: no IDE-Interface detected
Detected STB:
Vendor: Nokia
Model: D-BOX2 (2 flash chips)
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
insmod: warning: kernel-module version mismatch
ves1820 was compiled for kernel version 2.4.34-dbox2
while this kernel is version 2.4.37.6-dbox2
insmod: ves1x93.o: module not found
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.100 2009/09/11 05:58:41 rhabarber1848 Exp $
avia_av: AVIA 500 LB4 found, sptsfix is on
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
starting pid 112, tty '': '/etc/init.d/start'

Please press Enter to activate this console.
$Id: cdkVcInfo.cpp 1165 2009-11-04 08:16:00Z FlatTV $
/bin/lcdmenu: /lib/libpng12.so.0: no version information available (required by
/lib/liblcddisplay.so.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[lcdmenu] /bin/enigma was not found, entry Enigma discarded
[lcdmenu] /bin/radiobox was not found, entry Radiobox discarded
[lcdmenu] /bin/lcars was not found, entry Lcars discarded
[lcdmenu] /etc/init.d/initialize was not found, entry Initialize discarded
[lcdmenu] Only one GUI was found, selecting that
[Usercontroll] usercontroll by PPCBoot - fixed by Trapped $
[Usercontroll] Starting Usermanagment
[Usercontroll] No Usermanagment available, given up to Neutrino
Thu Jan 1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.314 2009/10/22 20:48:22 seife Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 3 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
rdate: bad address 'time.fu-berlin.de'
[timerd] woke up from timer? false!
emu_starts: Start Emu
/var/plugins/emu_handling: emu_handling
ACTION: start
EMU: .newcs
FLEX:
/var/plugins/emu_handling: start newcs
$Id: zapit.cpp 1183 2009-11-11 19:39:06Z FlatTV $
Lade Modul: camd-cardserver
[frontend] uncommitted_switch_mode 0 auto_fec 0
[frontend.cpp:CFrontend:63] /dev/dvb/adapter0/frontend0: No such file or directo
ry
/share/tuxbox/satellites.xml: No such file or directory
[camd-cardserver.o] compiled Nov 12 2009, 16:09:20
[camd-cardserver.o] ioport base = ff000950
[camd-cardserver.o] commproc base = ff0009c0
[getservices] satellites.xml
Modul camd-cardserver erfolgreich geladen
This is NewCS 1.65 - the New CardServer by the Butter-team..
Compiled on Jan 19 2009 at 17:54:45
Reading Config file from /var/tuxbox/config/newcs.xml
TCP-log password is disabled!
level: normal
type: init
output: all
logger config: level 1 type 3 output 255
Console log options: level 1 type 3
log file:
logger: cant open file , file log disabled
logger: no udp host defined, udp log disabled
TCP log options: level 1 type 3
[ 01:00:06 ] [ Box detect ] Box type 4 (Dbox2)
[ 01:00:06 ] [ Config ] Option <blockc0> for device 0 (NG_Return) not present, d
efaulting to NO
[ 01:00:06 ] [ Config ] Option <Seca-PPV> for device 0 (NG_Return) not present,
defaulting to NO
/var/tuxbox/config/zapit/ubouquets.xml: No such file or directory
[ 01:00:06 ] [ Config ] /dev/tts/1 ECM priority: round
[ 01:00:07 ] [ httpd ] httpd-user: newcs, password: newcs, accesslevel: admin
[ 01:00:07 ] [ EMM Cache ] Initialising dynamic Cache
[ 01:00:07 ] [ ECM Cache ] Initialising dynamic Cache
[ NewCS ] Process ID is: 178
[ 01:00:07 ] [ Loader ] Starting Telnet on port 3001
[ 01:00:07 ] [ Loader ] Started HTTP-server on port: 3005
[ 01:00:08 ] [ Loader ] Reader type 4 on node /dev/tts/1
[ 01:00:08 ] [ Dbox ] Opening device /dev/tts/1
/tmp/currentservices.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[CVideo::setVideoFormat] output format: 4:3(LB)
[ 01:00:09 ] [ Loader ] Reset failed ...
[ 01:00:10 ] [ Loader ] Starting Newcamd Server on port 10110
[ 01:00:10 ] [ Newcamd ] Newcamd thread Server started on port 10110
[ 01:00:10 ] [ NewCS ] Ready to GO!
newcamd: main loop
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib
/liblcddisplay.so.0)
/var/plugins/emu_handling: emu_handling
ACTION: start
EMU: .cccam
FLEX:
[Neutrino-Check] License valid. Name of User: NG-Return
/var/plugins/emu_handling: start capmtserver
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)
[neutrino] setRepeat: delay=150 period=150 use kernel-repeat: no
[neutrino] registering as event client
/share/tuxbox/satellites.xml: No such file or directory
[CBasicClient] receive failed: /tmp/zapit.sock
[scan-setup] received 0 sats
/var/plugins/emu_handling: start cccam
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[neutrino] no file /var/tuxbox/config/init.end was found
[neutrino] initialized everything
nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/l
iblcddisplay.so.0)
zap failed!
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
[sectionsd] getUTC: read: Connection timed out
rdate: bad address 'time.fu-berlin.de'
[sectionsd] getUTC: read: Connection timed out
rdate: bad address 'time.fu-berlin.de'

[dietmarw]

...
insmod: warning: kernel-module version mismatch
ves1820 was compiled for kernel version 2.4.34-dbox2
while this kernel is version 2.4.37.6-dbox2
insmod: ves1x93.o: module not found
...

...
emu_starts: Start Emu
/var/plugins/emu_handling: emu_handling
ACTION: start
EMU: .newcs
FLEX:
/var/plugins/emu_handling: start newcs
...

erstmal is das image zusammengewürfelt..

und zweitens is man hier mit emu quatsch fehl am platze..!

[GAT81]

Weiß zwar nicht was du hast .. was kann ich dafür das im Soglospaket die Emus installiert sind.. hier geht es um die Frage wieso der einen SAT tuner erkennt und nicht wie er sollte die Kabelversion

[rhabarber1848]

Tritt das Problem auch mit einem richtigen Image auf?

[GAT81]

Habe jetzt mehrere probiert .. alles wird weiter als SAT angezeigt !

[rhabarber1848]

Habe jetzt mehrere probiert .. alles wird weiter als SAT angezeigt !

Könntest Du bitte das Bootlog eines Original-CVS- oder JTG-Images posten?

[dbt]

Es wurde schon mal gesagt, das Image ist dem Log zufolge, an einigen Stellen ein ziemliches Stückwerk. Ein Bootlog wo auch die passenden Module für Tuner und Co. geladen werden hilft sicher mehr, wenn sich dadurch sogar nicht das Problem von selbst löst.

[GAT81]

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: unknown demodulatordebug: BMon V1.0 mID 01
debug: feID 00 gtxID 0b
debug: fpID 5a dsID 01-70.83.23.07.00.00-a2
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 171660
verify sig: 262
Branching to 0x40000


U-Boot 2009.08 (Tuxbox) (Sep 26 2009 - 14:36:43)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .... .
env: found console with value ttyS0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
LCD: ready

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 671052 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
Image Name: Linux-2.4.37.6-dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 670988 Bytes = 655.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37.6-dbox2 (image@Server) (gcc version 3.4.6) #26 Sa Sep 26 14
:37:12 CEST 2009
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600
dbox_duplex=
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:19:21:46
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x005e0000 : "root (squashfs+lzma)"
0x005e0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.14.4 (2009-09-26 14:42:24 CEST)
starting pid 8, tty '': '/etc/init.d/rcS'
mount: using /etc/fstab


##### Image-Version: Keywelt_Sep2009_V1 #####

Sat Sep 26 14:57:00 UTC 2009
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
tuxbox: no IDE-Interface detected
Detected STB:
Vendor: Nokia
Model: D-BOX2
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
insmod: warning: kernel-module version mismatch
dbox2_fp_input was compiled for kernel version 2.4.37-dbox2
while this kernel is version 2.4.37.6-dbox2
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.100 2009/09/11 05:58:41 rhabarber1848 Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: AVIA 500 LB4 found, sptsfix is off
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
insmod: warning: kernel-module version mismatch
multicam was compiled for kernel version 2.4.37-dbox2
while this kernel is version 2.4.37.6-dbox2
DBox2 Multicam Driver v1.01 skars & doz21
starting pid 171, tty '': '/etc/init.d/start'

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.306 2009/09/
14 13:33:28 seife Exp $
[sectionsd] Caching max 1500 events
[sectionsd] Caching 4 days
[sectionsd] Caching 12 hours Extended Text
[sectionsd] Events are old 120min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[timerd] woke up from timer? false!
/var/plugins/operations camd_init
/var/plugins/operations cardserver_start
$Id: zapit.cpp,v 1.440k 2009/09/18 20:30:00 rhabarber1848 & Worschter & SnowHead
Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0 auto_fec 0
[frontend.cpp:CFrontend:63] /dev/dvb/adapter0/frontend0: No such file or directo
ry
/var/plugins/operations camd_start
starte camd2
[camd2] EMM : active
[camd2] Socket=/tmp/camd.sock02
[camd] ca system id: 1702
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 1 onid 85
/var/tuxbox/config/zapit/ubouquets.xml: No such file or directory
/tmp/currentservices.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[CVideo::setVideoFormat] output format: 4:3(LB)
/bin/nhttpd: /lib/libpng12.so.0: no version information available (required by /
lib/liblcddisplay.so.0)
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
/var/plugins/operations sect_renice
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib
/liblcddisplay.so.0)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[sectionsd] getUTC: read: Connection timed out
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] found esound, adding to mainmenue/personalize
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)
[neutrino] setRepeat: delay=150 period=125 use kernel-repeat: no
[neutrino] received 29 sats
[neutrino] registering as event client
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[zapit] LOCK LOST! trying rezap... channel: 'Das Erste'
[basicsocket] receive timed out. waiting process 438
[neutrino] no file /var/tuxbox/config/init.end was found
[neutrino] initialized everything
busy /tmp/zapit.sock
[basicsocket] send_data: Broken pipe (n = 8/8, pid = 386)
zap failed!
[zapit] LOCK LOST! trying rezap... channel: 'Das Erste'
[zapit] LOCK LOST! trying rezap... channel: 'Das Erste'
[sectionsd] getUTC: read: Connection timed out
[zapit] LOCK LOST! trying rezap... channel: 'Das Erste'
[zapit] LOCK LOST! trying rezap... channel: 'Das Erste'

[dbt]

Ist das denn wirklich sooo schwer, ein Image mit Original Treibern zu nehmen? klick

[tik-tak]

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: unknown demodulatordebug: BMon V1.0 mID 01
debug: feID 00 gtxID 0b
debug: fpID 5a dsID 01-70.83.23.07.00.00-a2
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed


Also der Tuner wird nicht erkannt

Kriegt der Tuner alle Spannungen , wenn ja , dann halt VES -Chip im Eimer

[GAT81]

Sorry jetzt sollte es aber passen

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: unknown demodulatordebug: BMon V1.0 mID 01
debug: feID 00 gtxID 0b
debug: fpID 5a dsID 01-70.83.23.07.00.00-a2
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 170736
verify sig: 262
Branching to 0x40000


U-Boot 2009.08 (Tuxbox) (Feb 27 2010 - 06:50:54)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ............ .
find_inode failed for name=boot.conf
load: Failed to find inode
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
LCD: ready

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (jffs2) loading 'vmlinuz' to 0x200000
### FS load complete: 651189 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
Image Name: Linux-2.4.37.9-dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 651125 Bytes = 635.9 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37.9-dbox2 (dietmarw@lalelu.li) (gcc version 3.4.6) #3 Sat Feb
27 07:24:13 CET 2010
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rw rootfstype=jffs2 console=ttyS0,9600
dbox_duplex=
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30868k available (1104k kernel code, 336k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:19:21:46
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00800000 : "root (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.14.4 (2010-02-27 07:13:26 CET)
starting pid 9, tty '': '/etc/init.d/sysinit'
[BOOT] running /etc/init.d/sysinit
Thu Jan 1 01:00:00 UTC 1970
[BOOT] no /var MTD partition found (jffs2-image?)
starting pid 22, tty '': '/etc/init.d/rcS'

Please press Enter to activate this console. starting /etc/init.d/S05drivers ...

[BOOT] running /etc/init.d/S05drivers
tuxbox: no IDE-Interface detected
Detected STB:
Vendor: Nokia
Model: D-BOX2 (2 flash chips)
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
cam: no firmware file found
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.100 2009/09/11 05:58:41 rhabarber1848 Exp $
avia_av_core.c: avia_av_firmware_read: Unable to load '/var/tuxbox/ucodes/avia50
0.ux'.
avia_av: microcode not found, setting up dummy
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters enabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
/etc/init.d/S05drivers: line 1: can't create /etc/issue.net: No space left on de
vice
starting /etc/init.d/S09lcdip ...
writing /etc/network/interfaces: No space left on device
starting /etc/init.d/S10network ...
starting /etc/init.d/S10rtc ...
starting /etc/init.d/S15syslogd ...
mkdir: cannot create directory '/var/log': No space left on device
starting /etc/init.d/S18rdate ...
Jan 1 02:00:55 dbox syslog.info syslogd started: BusyBox v1.14.4
starting /etc/init.d/S20inetd ...
starting /etc/init.d/S25cdkVcInfo ...
starting /etc/init.d/S30autofs ...
[BOOT] Starting the automounter
mkdir: cannot create directory '/var/lock': No space left on device
starting /etc/init.d/S40tuxmaild ...
starting /etc/init.d/S99gui ...
Jan 1 02:00:57 dbox daemon.crit automount[159]: failed to mount a[camd] CA_SEND
_MSG: No such device
[camd] CA_SEND_MSG: No such device
/bin/enigma: /lib/libpng12.so.0: no version information available (required by /
bin/enigma)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
sh: can't open /share/keymaps/eng.kmap: no such file
/dev/dvb/adapter0/frontend0: No such file or directory
Segmentation fault
starting pid 187, tty '': '/etc/init.d/rcK'
stoping /etc/init.d/K99gui ...
stoping /etc/init.d/K40tuxmaild ...
stoping /etc/init.d/K30autofs ...
Stopping the automounter
/etc/init.d/K30autofs: line 69: can't open /var/run/automount.pid: no such file
kill: you need to specify whom to kill
stoping /etc/init.d/K25cdkVcInfo ...
stoping /etc/init.d/K20inetd ...
stoping /etc/init.d/K18rdate ...
stoping /etc/init.d/K15syslogd ...
mkdir: cannot create directory '/var/log': No space left on device
stoping /etc/init.d/K10rtc ...
stoping /etc/init.d/K10network ...
stoping /etc/init.d/K09lcdip ...
stoping /etc/init.d/K05drivers ...
CXA2092 found
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: unknown demodulatordebug: BMon V1.0 mID 01
debug: feID 00 gtxID 0b
debug: fpID 5a dsID 01-70.83.23.07.00.00-a2
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 170736
verify sig: 262
Branching to 0x40000


U-Boot 2009.08 (Tuxbox) (Feb 27 2010 - 06:50:54)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ..../

[GAT81]

Wie kann man denn das herausbekommen ob der Tuner vollen Saft bekommt ?

Ich sage mal so .. er schleift das Signal zum TV 1a durch ...

[juergeli]

guckst du hier

[GAT81]

Ach du Schei**e ... das ist zu viel für mich

[Miky1968]

Ach du Schei**e ... das ist zu viel für mich

Und das hat nichts mit dem verbastelten ersten Bootlog zu tun. Da hast Du nen Tunertreiber drin, der so nicht im Image war. Auch gibt es auch von dort kein Sorglospaket.

Schau Dich mal nach nem vernünftigen Reparaturservice um, ggf. mal ne Mail an Stingray oder sonst jemanden, damit Du hier nicht versauerst

[tik-tak]

$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
cam: no firmware file found
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.100 2009/09/11 05:58:41 rhabarber1848 Exp $
avia_av_core.c: avia_av_firmware_read: Unable to load '/var/tuxbox/ucodes/avia50
0.ux'.
avia_av: microcode not found, setting up dummy
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $

Da fehlt noch etwas

[GAT81]

Verstehe ich jetzt nicht ...
habe das enigma-jffs2.imgx2 druff gespielt

das image bootet nach der ip-eingabe neu ! und der bootlog beginnt ebenfalls von vorne ...

was hat das mit dem microcode aufsich ?

[dwilx]

Verstehe ich jetzt nicht ...
was hat das mit dem microcode aufsich ?

Extra gerade so umgebogen: http://wiki.tuxbox-cvs.sourceforge.net/Microcode
und dann bitte das noch beachten: http://www.tuxbox-cvs.sourceforge.net/f ... 23&t=46283