ich versuche nun schon seit 2 wochen meine nokia 2xintel 600 unter linux ans laufen zu bekommen.
nach langem suchen (2 wochen) im www bin ich mehr oder weniger sicher, das beim rauskopieren des original images was schiefgelaufen ist. hier mal kurz was ich gemacht habe:
1. box in den debug mode gebracht
2. box getestet mit original soft -> box lief einwandfrei
3. mit dbox-boot das image ausgelesen
4. mit dbox-boot die ucodes extrahiert
5. schritt 2 erfolgreich ausgeführt
6. mit dbox-boot alexW2xbasimagev1.6.3 geflasht
7. nach reset cdk.cramfs und ucodes kopiert
8. box resettet, transponderscan durchgeführt -> keine sender gefunden
nach dem vergleich von meinem log mit logs hier aus dem forum glaube ich, das mein cam-alpha.bin file kaputt ist. hier mein logfile:
<debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.2 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-4c.39.43.07.00.00-50
debug: HWrev 09 FPrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044
will verify ELF image, start= 0x800000, size= 203620
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Feb 17 2003 - 19:30:34)
CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 634725 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 634661 Bytes = 619 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft ;-) #1 Die Dez 31 18:36:38 CET 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 251625000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30816k available (1120k kernel code, 372k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:41:96:d8
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu
les/2.4.20/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.20/misc/event.o
event: init ...
Using /lib/modules/2.4.20/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20/misc/dvb_demux.o
Using /lib/modules/2.4.20/misc/dvbdev.o
Using /lib/modules/2.4.20/misc/avia.o
AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $
Using /lib/modules/2.4.20/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
Using /lib/modules/2.4.20/misc/cam.o
der moment ist gekommen...
Oops: kernel access of bad area, sig: 11
NIP: C000AA98 XER: 00000000 LR: C38E4898 SP: C1CE9E30 REGS: c1ce9d80 TRAP: 0300
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: C3916000, DSISR: C0000000
TASK = c1ce8000[38] 'insmod' Last syscall: 6
last math 00000000 last altivec 00000000
GPR00: 00000000 C1CE9E30 C1CE8000 C38E8000 C3915FFC 00020000 C38F4FFC D02C522B
GPR08: 75ADA500 C38E0000 C38C0000 C000AA7C 44002089 00000000 00000000 00000000
GPR16: 00000000 00000000 00000000 00000000 00009032 01CE9F40 C1CE9EA8 10076228
GPR24: C1AE0000 C01F7E40 C0130000 C3909000 C0140000 00068D58 FFFFFFFF FF0009C0
Call backtrace:
C38E4878 C38E4BA0 C38E5184 C0010190 C00025DC 10017A34 10018F18
10003C84 10003890 0FEF5350 00000000
Segmentation fault
Using /lib/modules/2.4.20/misc/dmxdev.o
write 1 event's ...
write 1 event's ...
Using /lib/modules/2.4.20/misc/dvb_frontend.o
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Bold)
Using /lib/modules/2.4.20/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.22 2002/09/13 22:53:55 Jolt Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.17 2002/09/15 18:06:26 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.6 2002/09/19 21:09:20 Jolt Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.134 2002/09/21 00:00:08 Jolt Exp $
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.18 2002/09/25 18:50:52 Jolt Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.20/misc/dvb.o
dvb.c: init_dvb
Init VES1893
Using /lib/modules/2.4.20/misc/ves1893.o
i2c-core.o: driver VES1893 DVB demodulator registered.
i2c-core.o: client [VES1893] registered to adapter [](pos. 3).
VES1893: attaching VES1893 at 0x10 to adapter
Using /lib/modules/2.4.20/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.130 2002/09/18 15:57:24 Jolt Exp $
avia_gt_napi: hardware section filtering disabled.
Using /lib/modules/2.4.20/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.16 2002/08/22 13:39:33 Jolt Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
Using /lib/modules/2.4.20/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.36 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.20/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.11 2002/09/25 18:50:52 Jolt Exp $
Using /lib/modules/2.4.20/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.4 2002/08/22 13:39:33 Jolt Exp $
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.1 2002/12/19 16:10:45 alexW Exp $
$Id: sectionsd.cpp,v 1.148 2002/12/09 20:07:52 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
$Id: zapit.cpp,v 1.287 2003/02/04 15:18:55 alexw Exp $
/var/tuxbox/config/zapit/services.xml: No such file or directory
Controld $Id: controld.cpp,v 1.90 2003/02/10 11:09:46 thegoodguy Exp $
[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.411 2003/02/15 01:42:31 zwen Exp $
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
IP : 10.1.50.3
Netmask : 255.255.255.0
Broadcast: 10.1.50.255
Gateway : 10.1.50.1
Mount 10.1.50.1:/mnt/data -> /mnt
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
loading locales: scandir: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
[CFrontend::getEvent] FE_FAILURE_EV
****************
No signal found on transponder (10876000 22000000 1)
****************
[CFrontend::getEvent] FE_FAILURE_EV
****************
No signal found on transponder (10861750 22000000 0)
****************
[CFrontend::getEvent] FE_COMPLETION_EV: freq 1139000
[dmx.cpp:readDmx:289] DMX_READ: Connection timed out
no new transponder(s) in current nit
[CFrontend::getEvent] FE_COMPLETION_EV: freq 1236500
[dmx.cpp:readDmx:289] DMX_READ: Connection timed out
no new transponder(s) in current nit
/var/tuxbox/config/zapit/services.xml: No such file or directory
und die ucodes:
101374 avia500.ux
128214 avia600.ux
49375 cam-alpha.bin
1267512 os
2048 ucode.bin
irgendwo habe ich gelesen das die cam-alpha.bin genau 1xx.xxx byte (genaue grösse weiss ich nicht mehr) sein muss wobei jemand sagte, seine datei sei kleiner (aber immer noch 1xx.xxx) und es liefe trotzdem alles. kann mir jemand sagen, ob meine files wenigstens von der grösse ok sind?
wenn nicht, wo bekomme ich passende files?
vielen dank schonmal...
p.s. ich habe das alles OHNE karte gemacht, da ich kein abo habe und auch nicht an einem abo, emu oder funcards interessiert bin.
p.p.s. als mp3 player funktionierts schonmal
p.p.p.s habe heute morgen alexw 1.6.8 mit neuem cramfs eingespielt. das log ist auch davon
