Hallo zusammen,
in dem (erstklassigen) Forum hier habe ich schon oft gelesen, dass die Box durch aufspielen eines neuen Images "geschrottet" wurde. Desahlb michte ich un versuchen eine neue Software (yadd) über Netz zu booten.
So wie ich den Bootlog interpretiere, sieht das soweit ganz gut aus, bis z dem Punkt, wo ein File avia600.ux verlangt wird. Stimmt, das ist nicht da.
Aber wo kriege ich das her ?
Auf meiner DBox2 (Sagem, 1*Intel) war schon Linux und ein Original Image habe ich nicht.
Kann ich noch was aus dem Linux Image generieren ?
Danke & Gruss
Kruepfel
p.s. der Bootlog
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-14.cd.b8.07.00.00-83
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 140.140.140.10, My IP 140.140.140.14
debug: Sending TFTP-request for file D/dbox_test/yadd/tftpboot/ppcboot
will verify ELF image, start= 0x800000, size= 204200
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
ppcboot 0.6.4 (Jun 24 2002 - 20:39:15)
Initializing...
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-3c-9a-88
FLASH: 8 MB
LCD driver (KS0713) initialized
BOOTP broadcast 1
TFTP from server 140.140.140.10; our IP address is 140.140.140.14
Filename 'D/dbox_test/yadd/tftpboot/logo-lcd'.
Load address: 0x130000
Loading: ##
LCD logo at: 0x130000 (0x1FD2814 bytes)
BOOTP broadcast 1
TFTP from server 140.140.140.10; our IP address is 140.140.140.14
Filename 'D/dbox_test/yadd/tftpboot/logo-fb'.
Load address: 0x120000
Loading: ##############
FB logo at: 0x0 (0x1FC0000 bytes)
AVIA Frambuffer
Input: serial
Output: serial
1: Console on ttyS0
2: Console on null
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
BOOTP broadcast 1
TFTP from server 140.140.140.10; our IP address is 140.140.140.14
Filename 'D/dbox_test/yadd/tftpboot/kernel-yadd'.
Load address: 0x100000
Loading: #######################################################################
#############################################
## Booting Linux kernel at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 590089 Bytes = 576 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft ;-) #1 Mon Sep 23 08:56:15 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 ip=bootp root=/dev/nfs rw nfsroot=140.140.140
.10:D/dbox_test/yadd/yaddroot/
WARNING: Frequency is not in HZ. Please consider using a newer bootloader!
WARNING: OLD intfreq = 66 busfreq = 66
WARNING: NEW intfreq = 66000000 busfreq = 66000000
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.53 BogoMIPS
Memory: 30944k available (1036k kernel code, 320k data, 68k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:3c:9a:88
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
Using buffer write method
Creating 3 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Sending BOOTP requests . OK
IP-Config: Got BOOTP answer from 140.140.140.10, my address is 140.140.140.14
IP-Config: Guessing netmask 255.255.0.0
IP-Config: Complete:
device=eth0, addr=140.140.140.14, mask=255.255.0.0, gw=255.255.255.255,
host=140.140.140.14, domain=, nis-domain=(none),
bootserver=140.140.140.10, rootserver=140.140.140.10, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 140.140.140.10
Looking up port of RPC 100005/1 on 140.140.140.10
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 68k init
init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu
les/2.4.19/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.19/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.19/misc/event.o
event: init ...
Using /lib/modules/2.4.19/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [](pos. 0).
Using /lib/modules/2.4.19/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.19/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.19/misc/dvb_demux.o
Using /lib/modules/2.4.19/misc/dvbdev.o
Using /lib/modules/2.4.19/misc/avia.o
AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $
avia_core.c: do_firmread: Unable to load '/var/tuxbox/ucodes/avia600.ux'.
insmod: init_module: avia: Input/output error
Using /lib/modules/2.4.19/misc/cam.o
insmod: init_module: cam: Input/output error
Using /lib/modules/2.4.19/misc/lcd.o
Using /lib/modules/2.4.19/misc/dmxdev.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 3
Using /lib/modules/2.4.19/misc/dvb_frontend.o
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
Using /lib/modules/2.4.19/misc/avia_gt.o
insmod: unresolved symbol avia_set_pcr
Using /lib/modules/2.4.19/misc/dvb.o
insmod: unresolved symbol avia_wait
insmod: unresolved symbol avia_wr
insmod: unresolved symbol avia_command
insmod: unresolved symbol avia_rd
insmod: unresolved symbol avia_flush_pcr
insmod: unresolved symbol cam_read_message
insmod: unresolved symbol cam_reset
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol cam_write_message
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
Init AT76C651
Using /lib/modules/2.4.19/misc/at76c651.o
insmod: unresolved symbol register_frontend
insmod: unresolved symbol unregister_frontend
Using /lib/modules/2.4.19/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol unregister_demux
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_dmx_release_section_filter
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_fake_queue_irq
insmod: unresolved symbol avia_gt_dmx_get_queue_irq
insmod: unresolved symbol avia_gt_dmx_set_filter_parameter_table
insmod: unresolved symbol register_demux
insmod: unresolved symbol avia_gt_dmx_set_pid_table
insmod: unresolved symbol avia_gt_dmx_force_discontinuity
insmod: unresolved symbol avia_gt_dmx_set_pid_control_table
insmod: unresolved symbol avia_gt_dmx_get_hw_sec_filt_avail
insmod: unresolved symbol avia_gt_dmx_get_queue_info
insmod: unresolved symbol avia_gt_dmx_set_section_filter
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_queue_irq_disable
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_message
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_free_irq
Using /lib/modules/2.4.19/misc/avia_gt_vbi.o
insmod: unresolved symbol avia_gt_get_info
Using /lib/modules/2.4.19/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.19/misc/avia_gt_oss.o
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_standby
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
cdkVcInfo $Id: cdkVcInfo.c,v 1.0 2002/09/26 20:48:26 alexW Exp $
Network LCD-Driver $Id: lcdd.cpp,v 1.54 2002/08/31 22:30:27 obi Exp $
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
/var/tuxbox/config/lcdd.conf: No such file or directory
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
[sectionsdclient] connect: No such file or directory
$Id: sectionsd.cpp,v 1.135 2002/10/04 16:31:25 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
[camd] /dev/dvb/card0/ca0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: DMX_STOP: Bad file descriptor
$Id: zapit.cpp,v 1.253 2002/10/04 18:25:17 thegoodguy Exp $
/var/tuxbox/config/zapit/services.xml: No such file or directory
[zapit] error parsing services!
/dev/dvb/card0/frontend0: No such file or directory
[zapit] unable to open frontend devices. bye.
Segmentation fault
Controld $Id: controld.cpp,v 1.64 2002/10/05 20:46:20 dirch Exp $
[controld] error while loading settings: /var/tuxbox/config/controld.conf
[controld] using defaults
[controld] Boxtype detected: (03, 3, 2, Sagem)
set event: 00000009
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.335 2002/10/05 20:46:20 dirch Exp $
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
CXA2126 found
Unmounting ramfs
umount: /var/tmp: Device or resource busy
The system is going down NOW !!
Sending SIGTERM to all processe[nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
System halt
