Kabelbox macht Sat-Suchlauf ???

[Kartenzwerg]

Hi,

meine Schwester hat sich eine D-Box Nokia2 Kabel auf dem Flohmarkt gekauft (naja ich hätte es nicht gemacht...) und die macht was eigenartiges:

Fährt schön mit Linux/Neutrino hoch und zeigt dann: keine Kanäle gefunden...

Beim Sendersuchlauf werden kurioserweise aber keine Kabelanbieter zum Auswählen (Telekom usw.) angezeigt, sondern SAT...irgendwas (sorry, hab vom Sat keine Ahnung).

Hab schon neu geflasht, hat sich nichts verändert...

Hat jemand ne Ahnung?

Gruß

Mike

[DieMade]

Bootlog?

Die Box wird das Frontend nicht sauber erkennen.

[Kartenzwerg]

Hallo,

habe es gerade mal mit Betanova versucht und bekam den berühmt/berüchtigten UD1-Fehler.

Das wird dann wohl am Tuner liegen...

[rmaerte1]

Nein! UD1 kommt, wenn Du eine nicht zu Deiner Box gehörendes BN Image draufflasht.
Mach mal wieder das AlexW drauf und poste Flash+Boot Log.

[DieMade]

UD1
- Ein Initialisierungsfahler des Front End es ist aufgetreten
- Reset ausführen
- Neu Starten

also stimmt die Aussage mit dem Tuner bzw. Frontend schon

[Kartenzwerg]

Der Vollständigkeit halber hier das Log, in den rot-markierten Bereichen dürfte das Problem liegen, richtig?


debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: unknown demodulatordebug: BMon V1.0 mID 01
debug: feID 00 gtxID 0b
debug: fpID 5a dsID 01-00.00.00.00.00.00-42
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044

will verify ELF image, start= 0x800000, size= 203620
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Mar 13 2003 - 12:11:32)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 635882 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux K
Data Size: 635818 Bytes = 620 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht, wir
d bestraft ;-) #1 Son Apr 13 14:33:10 CEST 2003
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30812k available (1120k kernel code, 376k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 9, console /dev/console: '/etc/init.d/rcS') multi-ca
Using /lib/modules/2.4.20-dbox2/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20-dbox2/misc/info.o
SIOCADDRT: Invalid argument
ifup: Ignoring unknown interface net
ifup: i2c-core.o: driver FOR_PROBE_ONLY registered.
Ignoring unknown interface loopbi2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
acki2c-core.o: driver unregistered: FOR_PROBE_ONLY

Using /lib/modules/2.4.20-dbox2/misc/event.o
event: init ...
Using /lib/modules/2.4.20-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20-dbox2/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20-dbox2/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20-dbox2/misc/dv
Using /lib/modules/2.4.20-dbox2/misc/lcd.o
Using /lib/modules/2.4.20-dbox2/misc/dvbdev.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
Using /lib/modules/2.4.20-dbox2/misc/avia.o
AVIA: $Id: avia_core.c,v 1.35.2.1 2003/02/18 14:53:34 alexw Exp $
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
write 1 event's ...
write 1 event's ...
Using /lib/modules/2.4.20-dbox2/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
Using /lib/modules/2.4.20-dbox2/misc/dmxdev.o
Using /lib/modules/2.4.20-dbox2/misc/dvb_frontend.o
Using /lib/modules/2.4.20-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.23.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.17 2002/09/15 18:06:26 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.8.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.139.2.1.2.2 2003/04/14 14:11:33 alexw Exp $
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.25.4.3 2003/04/10 14:54:22 zwen
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.19.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.20-dbox2/misc/dvb.o
dvb.c: init_dvb
Init VES1893
Using /lib/modules/2.4.20-dbox2/misc/ves1893.o
i2c-core.o: driver VES1893 DVB demodulator registered.
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.141.2.1.2.1 2003/02/18 14:32:46 alexw Exp
$
avia_gt_napi: hardware section filtering disabled.
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.17.4.1 2003/02/18 14:32:46 alexw Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.38.4.5 2003/03/05
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.12.4.1 2003/02/18 14:32:46 alexw Exp $
Using /lib/modules/2.4.20-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.4 2002/08/22 13:39:33 Jolt Exp $
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.2.1 2003/03/13 15:11:22 alexW Exp $

$Id: sectionsd.cpp,v 1.166 2003/03/14 04:27:55 obi Exp $
caching 504 hours
events are old 60min after their end time
[camd] Unknown 1.CMD-Class 03
[camd] no card is in slot #2
[camd] no card is in slot #1
[camd] ca system id: 1722
$Id: zapit.cpp,v 1.290.2.18 2003/03/27 11:04:52 thegoodguy Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
[frontend.cpp:CFrontend:67] FE_GET_INFO: Operation not permitted
[zapit] unable to open frontend devices. bye.
$Id: controld.cpp,v 1.104 2003/03/19 20:59:02 thegoodguy Exp $

[controld] Boxtype detected: (1)
set event: 00000009
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or dire
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[camd] no card is in slot #2
[camd] no card is in slot #1
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.433 2003/04/01 17:30:24 thegoodguy E
xp $

[neutrino] frameBuffer Instance creat
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
loading locales: scandir: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[neutrino] timerd event register
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory

[DieMade]

Ja, es ist das Frontend (allgemein auch "Tuner" genannt, was nicht ganz richtig ist).

[doc]

debug: unknown demodulatordebug:

Na steht es doch schon. Entweder keine Spannung für den Tuner oder Tuner selber defekt oder auch FP "teildefekt".