nokia 2xi problem

[pippolo]

hi

i have a problem:
my nokia doesn't replies to ping
when a switch it on this message appears on LCD:

BMon v1.2 mID01
feID dd gtxID 0b
fpID 5a dsID 01-
9d.4c.83.07.00.00-25
hwrev 09 fp rev 0.81
b/ex/f1 (mb) 32/00/08

this means debugmode is enable, ok?

in dbox2bootmanager, when i try to flash, in "com-terminal" appears:

***Adapter Desc: Realtek 8139-series PCI NIC
***MAC address: 00:06:7B:03:1A:7E Local IP: 192.168.5.5 (via Packet-Driver #1)
***BootP server started... Port 67
***TFTP server started... Port 69

and no log because dbox doesn't replies to ping.

bootmanager settings are ok,
i use win98se
nullmodem cable ok-> tested with humax5400
i use a hub to connect pc<->dbox2
the hub recognize dbox ethernet card as 10 mbit



could it be ethernet dbox card broken???


can i try to enable again debugmode ??

thanks in advance,
have a nice day;)

[doc]

You dont need to enable the debugmode again! This is already don.

***Adapter Desc: Realtek 8139-series PCI NIC
***MAC address: 00:06:7B:03:1A:7E Local IP: 192.168.5.5 (via Packet-Driver #1)
***BootP server started... Port 67
***TFTP server started... Port 69

This is not from the COM Terminal! This is from the Network Terminal!

Please post a Log from the COM Terminal.
In this Log maybe it is to see why you can't flash.

[pippolo]

sorry, but in COM-Terminal i have no message,no log.

[Frockert]

sorry, but in COM-Terminal i have no message,no log.

Hmm,

how do you starting flashing?

Normaly you start the bootmanager and choose "utilities" and flash image.
after that you must choose your image and get start.

what appers at the screen, after you do that?

Another question, do you save your old software?
--> utilities -> read flash

regards
Frockert

[motrico17]

Bonjour
HI!
I have exactly the same problem !
My dbox2 is currently in "kein system" following an awkward handling.
With the same configuration as
"pipollo" here the log that I obtains.
The Help |!
A french newbie Karlos


"the log"

***Adapter Desc: Realtek 8139-series PCI NIC
***MAC address: 00:50:FC:6F:89:84 Local IP: 192.168.0.4 (via Packet-Driver #0)
***BootP server started... Port 67
***TFTP server started... Port 69
......................................................
debug:
etc....
debug: Given up BOOTP/TFTP boot
boot net failed ??????????????????
----etc

[zexma]

debug: Given up BOOTP/TFTP boot
boot net failed ??????????????????
----etc

Salut motrico17,
http://www.dietmar-h.net/flashprob_eng.html
à bientôt!

[doc]

@pippolo
Did you install the latest Driver for the Realtek 8139? Some old Driver make Problems in same causes! The Effect ist the "boot net failed".

[pippolo]

@Frockert:
when i try to flash nothing comes on screen : COM-terminal is white, no log.
i can't connect TO the dbox.

@ DOC:
today i have tryed to flash with another pc and another ethernet card with the help of a "Friend" in chat.
the problem rest the same:
LCD stay in debug mode e no COM terminal answer.

i think it could be an hardware problem:
a bad firmware can cause that problem??

could it be a intel flash problem or com or ethernet??

bye

[doc]

In bad Times it can be all three things!

On top you wrote that the box starts with the BMon1.2.
In this cause you must have an Avia600 on the board! Is this right?

Otherwise you can try to cool down the IH11 and the IE1 (MB 86691A) and try again to flash.

[pippolo]

Yes, i have an AVIA 600.


i think it could be a bad software,
yesterday, i was trying some reset using button on front panel:
i have seen that: if i do a reset and i do another reset immediately on LCD appears the write: "NEUTRINO" but nothing works, it rests blocked.

"Otherwise you can try to cool down the IH11 and the IE1 (MB 86691A) and try again to flash."

i'll try with an impeller...


i can do all test, no problem;)

[doc]

No no I mean with an IceSpray!! down to -30°C.

The BMon is o.k. for this Avia.
There still I have no more Ideas!

[pippolo]

hei doc,

thanks for your adices;)

i will try the "LAST CHANCE"...
i'll make extract my flashes and i will make reprogram them externally,


but i must find FILES to put in flashes....

...


bye;)

[pippolo]

sorry boys,

can i ask for bootloader to program externally my flash???

thanks in advance,
Pippolo.