Das kam, nachdem ich Einstellungen Console seriell gewählt habe.
Hoffentlich kannst du damit was anfangen. Ich seh am Ende nur
viele Fehlermeldungen.
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-94.48.eb.07.00.00-20
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0040
will verify ELF image, start= 0x800000, size= 148088
verify sig: 263
Branching to 0x40000
U-Boot 1.0.2 (TuxBox) (Feb 29 2004 - 10:30:37)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load complete: 602506 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 602442 Bytes = 588.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.25-dbox2 (von alexW) (gcc version 3.3.3) #1 Fr Feb 20 21:32:40
CET 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30924k available (1020k kernel code, 364k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (
rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:3d:7b:df
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit mode
Intel/Sharp Extended Query Table at 0x0031
cfi_cmdset_0001: Erase suspend on write enabled
Using buffer write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS') multi-c
Using /lib/modules/2.4.25-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.25-dbox2/misc/dvb-core.o
SIOCADDRT: Invalid argument
Using /lib/modules/2.4.25-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_input.o
chk_inputseq $Id: chk_inputseq.c,v 1.1 2003/10/17 11:12:48 alexw Exp $
Using /lib/modules/2.4.25-dbox2/misc/avs.o
Using /lib/modules/2.4.25-dbox2/misc/saa7126.o
Using /lib/modules/2.4.25-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.25-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.25-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.25-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.25-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.89 2004/02/27 22:17:44 obi Exp $
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.44 2003/12/22 05:31:39 obi Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.201 2004/02/01 13:50:23 wjoost Exp $
avia_gt_dmx: loaded ucode vB107
avia_gt_dmx: hw section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.37 2003/09/30 05:45:35 obi Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.53 2003/12/22 04:02:05 obi Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.25-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
cdkVcInfo $Id: cdkVcInfo.c,v 1.9 2004/02/27 19:13:17 alexw Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.25 2004/01/30 08:24:42 zwen Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/ves1x93.o
Using /lib/modules/2.4.25-dbox2/misc/at76c651.o
DVB: registering frontend 0:0 (Atmel AT76C651A with DAT7021(TUA6010XS))...
Using /lib/modules/2.4.25-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.31 2004/03/02 22:38:31 alexw Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.198 2004/02/17 19:51:09 wjoost Exp $
$Id: sectionsd.cpp,v 1.171 2004/02/25 00:28:12 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
Segmentation fault
$Id: zapit.cpp,v 1.344 2004/02/25 10:45:35 thegoodguy Exp $
[camd] /dev/dvb/card0/ca0: No such file or directory
$Id: controld.cpp,v 1.115 2004/02/19 23:00:33 zwen Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[cdkVcInfo] Version (Image): 1107200403030001
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] registering as event client
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
[neutrino] initialized everything
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
PES, queue 0 normal.
[CBasicClient] connect failed.
/tmp/camd.socket: No such file or directory
