yweb ,nhttpd ? automatich starten ?

Hi ich habe eine frage ich habe grade das web interface upgedatet aber wenn ich die box neu starte muss ich immer erst den deamon von hand starten wo und wie kann ich das einstellen das er beim booten mit gestartet wird ? viel dank gruß spion77

übrigens habe ich das aktuelle yadi image und auch schon die such funktion benutzt aber habe nix passendes gefunden ! danke

Was hast Du denn für ein Image auf der Box?

cu
Jens

yadi 2.1.0.9

Hast Du da versucht Y-Web mit einem alten Installer drauf zu machen? Das ist im Image schon drin und sollte auch mit starten. Wenn eine zusätzliche manuelle Installation vorhanden ist, kann es da aber schonmal etwas durcheinander gehen. Lösch mal den Ordner /var/nhttp und in /var/tuxbox/config die nhttpd.conf und starte dann die Box neu.

cu
Jens

Hi habe /var/nhttp und die bhttpd.conf gelöscht und neu gestartet geht aber immer noch nicht soll heisen muss immer noch den deamon laden per hand

ich habe den installer Release 1.4.0 benutzt ! war das flasch ?

Ja, da die Version (wahrscheinlich, ich nutze kein Yadi) schon drin ist.

Starte die Box nochmal neu, wenn dann Yweb nicht aktiv ist, poste mal den Inhalt der nhttpd.conf und ein Bootlog.

cu
Jens

~debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-e8.98.23.07.00.00-be
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 160940
verify sig: 263
Branching to 0x40000

U-Boot 1.1.2 (Tuxbox) (May 26 2005 - 16:37:05)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .

.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 666413 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 666349 Bytes = 650.7 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.31-dbox2 (ImageTeam@yadi.org) (gcc version 3.4.4) #2 So Nov 20
21:22:49 CET 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30832k available (1132k kernel code, 344k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1a:35:e9
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.31-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.31-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.31-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.31-dbox2/misc/avs.o
Using /lib/modules/2.4.31-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.31-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.31-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.31-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.31-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_napi.o
Thu Jan 1 01:00:00 CET 1970
Using /lib/modules/2.4.31-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.31-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/ves1820.o
Using /lib/modules/2.4.31-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.31-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Using /lib/modules/2.4.31-dbox2/misc/dvb2eth.o
Using /lib/modules/2.4.31-dbox2/misc/aviaEXT.o
Using /lib/modules/2.4.31-dbox2/kernel/net/sunrpc/sunrpc.o
$Id: chkIVersion.cpp,v 1.8 2005/09/14 21:55:37 mogway Exp $
Yadi Snapshot vom 20.11.2005 19:59 - Image-Version 2.1.0.9
Networkcfg eth0: 192.168.100.193/255.255.255.0 gw 192.168.100.1 ns 192.168.100.1

Using /lib/modules/2.4.31-dbox2/kernel/fs/lockd/lockd.o
Startmode: Bootmenu - HWS: on
Using /lib/modules/2.4.31-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.31-dbox2/kernel/fs/cifs/cifs.o
Starting pid 97, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.197 2005/11/
20 15:11:40 mogway Exp $
caching 504 hours
events are old 180min after their end time
[camd] ca system id: 1702
$Id: zapit.cpp,v 1.378 2005/11/20 15:10:52 mogway Exp $
[camd] no card is in slot #2
[camd] no card is in slot #1
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $

Bus error
[controld] Boxtype detected: (1, Nokia D-BOX2)
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_core: masking unhandled irq reg 0 bit 7
PES, queue 0 normal.
[camd] program number 002e unsupported due to missing parental coavia_gt_core: m
asking unhandled irq reg 1 bit 15
ntrol
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3)
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[timeThread] time(): 20.12.2005 17:47:35, tim: Tue Dec 20 17:47:35 2005
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
PES, queue 0 normal.
[camd] program number 002e unsupported due to missing parental control
[neutrino] initialized everything
[timeThread] time(): 20.12.2005 17:47:46, tim: Tue Dec 20 17:47:46 2005

und die conf datei

AuthPassword=dbox2
AuthUser=root
Authenticate=false
LOG=false
NewGui=true
Port=80
PrivatDocRoot=/share/tuxbox/neutrino/httpd-y
PublicDocRoot=/var/httpd
THREADS=true
VERBOSE=false
Zapit_XML_Path=/var/tuxbox/config/zapit
/var/tuxbox/config #

mir ist jetzt grade aufgefallen ich habe diesen ordner der in der conf datei steht nicht /var/httpd wofür steht denn dieser PublicDocRoot ?

Hmm - schau mal nach, ob noch irgendwo in der Start_Neutrino ein Aufruf für den nhttpd aus /var/bin drin ist und ändere den, damit nhttpd aus /bin startet. Und lösche den aus /bin. Wenn die start_neutrino von Dir sonst nicht benutzt wird, kannste die auch ganz löschen.

cu
Jens

Beitrag von **yjogol** » Dienstag 20. Dezember 2005, 18:24

Code: Alles auswählen

$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $ 

Bus error 
[controld] Boxtype detected: (1, Nokia D-BOX2) 
avia_gt_core: masking unhandled irq reg 0 bit 6 
avia_gt_core: masking unhandled irq reg 0 bit 7

"bus error" ist keine gute Meldung.
Flash am besten mal neu.

Gruß
yjogol

ja ich denke auch ich werde neu flashen ! vielen dank trozdem !! super service hier !