Kein Empfang -> Satfind werte ok ....

Beitrag von **Caradas** » Freitag 26. Mai 2006, 22:58

Hallo,

Ich habe folgendes Problem:
Auf meiner Nokia (Avia 600) bekomme ich keine Sender. Weder über fertige Kanalliste oder über Kanalsuchlauf. Seltsamerweise funktioniert der Empfang mit der BN-Software. Bei Satfind mit Linux sind alle Werte OK Ber 0 usw.

So die Informationen kurzgefasst:
Nokia Dbox 2 Avia 600
DietmarW vom 26.5
Bootlog folgt (in arbeit)

---
Ich für mein teil Tippe auf SEC (Was kostet der zum reparieren)

Beitrag von **DieMade** » Samstag 27. Mai 2006, 11:29

Ein Hardwaredefekt würde sich auch unter BetaNova auswirken.

Poste bitte die Version der uCodes und ein Bootlog inkl. Kanalsuche.

Beitrag von **Caradas** » Samstag 27. Mai 2006, 12:14

Code: Alles auswählen

dbox2:root> debug: 
BOOTP/TFTP bootstrap loader (v0.3)
debug: 
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032

will verify ELF image, start= 0x800000, size= 149536
verify sig: 262
Branching to 0x40000


U-Boot 1.1.4 (Tuxbox) (May 26 2006 - 11:49:34)

CPU:   PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.2
       Watchdog enabled
I2C:   ready
DRAM:  32 MB
FLASH:  8 MB
Scanning JFFS2 FS: ........ done.
FB:    ready
LCD:   ready
In:    serial
Out:   serial
Err:   serial
Net:   SCC ETHERNET

Options:
  1: Console on null
  2: Console on ttyS0
  3: Console on framebuffer
Select option (1-3), other keys to stop autoboot:  0 
### FS (jffs2) loading 'vmlinuz' to 0x100000
### FS load complete: 657676 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
   Image Name:   dbox2
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    657612 Bytes = 642.2 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Linux version 2.4.32-dbox2 (dietmarw@linux) (gcc version 3.4.4) #4 Fr Mai 26 11:
49:59 CEST 2006
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rw rootfstype=jffs2
Decrementer Frequency = 251625000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2580)
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30820k available (1116k kernel code, 372k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:44:0b:15
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
 Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00800000 : "root (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 11, console /dev/console: '/etc/init.d/rcS'lti-call 
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Detected STB:
        Vendor: Nokia
        Model: D-BOX2 
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
DVB: registering frontend 0:0 (VES1893)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Starting pid 86, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. Thu Jan  1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.226 2006/05/22 17:48:55 mws Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Events are old 60min after their end time
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[camd] CA_SEND_MSG: Remote I/O error
[camd] CA_SEND_MSG: Remote I/O error
$Id: zapit.cpp,v 1.388 2006/05/19 21:26:42 houdini Exp $
/var/tuxbox/config/zapit/services.xml: No such file or directory
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[neutrino] initialized everything
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
[sectionsd] getUTC: read: Connection timed out
[zapit] scan mode full
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[sectionsd] getUTC: read: Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
^[[A[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
/var/tuxbox/config/zapit/bouquets.xml: No such file or directory
/tmp/currentservices.xml: No such file or directory

Beitrag von **Caradas** » Samstag 27. Mai 2006, 12:15

sry doppelpost (das forum is heute aber auch schnell oder)

Beitrag von **DieMade** » Samstag 27. Mai 2006, 13:28

Was sagt Neutrino zu den uCodes (besonders cam-alpha)?

Service - uCodes überprüfen

Beitrag von **Caradas** » Samstag 27. Mai 2006, 13:50

Avia 500: avia500v110
Avia 600: avia600vb002
Ucode: ucode_b107
Cam-Alpha: cam_01_02_105E

Beitrag von **DieMade** » Samstag 27. Mai 2006, 14:02

Die cam-alpha ist OK, eine Fehlermeldung bezüglich der Kommunikation mit dem SEC-Chip taucht aber trotzdem im Log auf. Das wäre die erste Box, bei der die BN einen (vermutlichen) HW-Defekt ausbügeln kann.

Beitrag von **gurgel** » Samstag 27. Mai 2006, 14:07

[camd] CA_SEND_MSG: Remote I/O error
[camd] CA_SEND_MSG: Remote I/O error

sram defekt.
Es kann schon gut sein dass das zeitweise mal funktioniert. Die Betanova bügelt das aber sicher nicht dauerhaft aus.

Beitrag von **Caradas** » Samstag 27. Mai 2006, 14:34

jo mitlerweile gehts nichtmal mehr mit bn (startet nich)

ach was kostet des zum reparieren? bzw kann man das selbst machen?

Beitrag von **admiral00** » Samstag 5. August 2006, 11:14

Caradas hat geschrieben:jo mitlerweile gehts nichtmal mehr mit bn (startet nich)

ach was kostet des zum reparieren? bzw kann man das selbst machen?

Habe selbiges Problem!!

Wo findes ich den sram auf der BOX??
Gibts da ein Bildchen davon??

Hallo

Ich habe hier eine Sagembox mit dem selben Fehler !

Wo ist der sram zu finden - Habt ihr Erfahrungswerte zu den tatsächlichen Kosten ?

Beitrag von **gurgel** » Freitag 17. November 2006, 15:27

wenns nur sram ist, und das ist meistens der Fall, dann 40â‚¬

Tuxbox-Board

Kein Empfang -> Satfind werte ok ....

Kein Empfang -> Satfind werte ok ....

Ok hier bootlog mit kannalsuche

Ok hier bootlog mit kannalsuche