Box über Netzwerk nicht mehr erreichbar

Das Original Benutzerinterface Neutrino-SD incl. zapit, sectionsd, yWeb etc...
HaeS
Neugieriger
Neugieriger
Beiträge: 18
Registriert: Sonntag 5. September 2004, 14:42

Box über Netzwerk nicht mehr erreichbar

Beitrag von HaeS »

Hallo! Ohne dass ich irgendwas umgestellt habe, funktioniert meine Netzwerkverbindung zur DBox II auf einmal nicht mehr (weder FTP noch ping). Habe die Netzwerkverbindung längere Zeit nicht benutzt und kann daher den Zeitraum nicht genau eingrenzen.

Bisher hatte ich die Box (Image YADI 2.1.0.11) über einen Router in meinem Netzwerk, was auch funktionierte. Jetzt geht weder DHCP, noch statische IP.

Netzwerk testen gibt folgende Ausgabe:

dbox: 192.168.1.6 ist erreichbar
alles andere nicht...

Die LED am Router leuchtet, wenn ich die Box einstecke, die physikalische Verbindung besteht also.

Habe die Box jetzt über ein Crossover-Kabel direkt mit einem PC verbunden. Der PC hat die IP 192.168.1.5, also gleiches Netz. Gateway und DNS hab ich leer gelassen. Verbindung bekomme ich auch hier keine.

Wie kann ich weiter vorgehen?

Edit: Hier noch mein Log vom Booten:

Code: Alles auswählen

�debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0  mID 01
debug: feID 7a    gtxID 0b
debug: fpID 5a     dsID 01-e4.4d.45.07.00.00-d6
debug: HWrev X5  SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug: 
BOOTP/TFTP bootstrap loader (v0.3)
debug: 
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 160940
verify sig: 263
Branching to 0x40000


U-Boot 1.1.2 (Tuxbox) (May 26 2005 - 16:37:05)

CPU:   PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
         *** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
       Watchdog enabled
I2C:   ready
DRAM:  32 MB
FLASH:  8 MB
Scanning JFFS2 FS: . done.
FB:    ready
LCD:   ready
In:    serial
Out:   serial
Err:   serial
Net:   SCC ETHERNET

Options:
  1: Console on null
  2: Console on ttyS0
  3: Console on framebuffer
Select option (1-3), other keys to stop autoboot:  0 
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 674386 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
   Image Name:   dbox2
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    674322 Bytes = 658.5 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Linux version 2.4.32-dbox2 (ImageTeam@yadi.org) (gcc version 3.4.4) #2 So Jun 25 15:17:53 CEST 2006
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30816k available (1148k kernel code, 344k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1f:1f:a0
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
 Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'lti-call 
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Detected STB:
  Vendor: Nokia
  Model: D-BOX2 
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Thu Jan  1 01:00:00 CET 1970
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
insmod: Warning: kernel-module version mismatch
        /lib/modules/2.4.32-dbox2/misc/cable_ves1820.o was compiled for kernel version 2.4.25-dbox2
        while this kernel is version 2.4.32-dbox2
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
$Id: chkIVersion.cpp,v 1.12 2005/12/21 22:23:20 mogway Exp $
Yadi Snapshot vom 25.06.2006 13:51 - Image-Version 2.1.0.11
Networkcfg eth0: 192.168.1.6/255.255.255.0 gw  ns 
Startmode: Bootmenu - HWS: on
Starting pid 98, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.227 2006/06/08 20:19:32 houdini Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Events are old 60min after their end time
[camd] ca system id: 1722
$Id: zapit.cpp,v 1.389 2006/06/08 20:17:58 houdini Exp $
avia_gt_core: masking unhandled irq reg 0 bit 7
[getservices] /var/tuxbox/config/zapit/myservices.xml  found.
/tmp/currentservices.xml: No such file or directory
$Id: controld.cpp,v 1.123 2006/06/18 10:39:40 barf Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 0 v3 = 1 a3 = 1 fblk=1
[nhttpd] Neutrino HTTP-Server starting..
[LCDFONT] initializing core...[camd] no card is in slot #2
[camd] no card is in slot #1

[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[CFSMounter] Mount(0) 192.168.1.5:/share/hdd/data/dbox -> /mnt/filme
[CFSMounter] FS mount error: "mount -t nfs 192.168.1.5:/share/hdd/data/dbox /mnt/filme -o rw,soft,tcp,vers=3,nolock,rsize=8192,wsize=8192"
[CFSMounter] Mount(0) 192.168.1.5:/share/hdd/data/dbox -> /mnt/custom
mount: nfsmount failed: Bad file descriptor
mount: Mounting 192.168.1.5:/share/hdd/data/dbox on /mnt/filme failed: Bad file descriptor
[CFSMounter] FS mount error: "mount -t nfs 192.168.1.5:/share/hdd/data/dbox /mnt/custom -o rw,soft,udp,vers=3,nolock,rsize=8192,wsize=8192"
[CFSMounter] Mount(0) 192.168.1.5:/share/hdd/data/dbox/mp3 -> /mnt/mp3
mount: RPC: Unable to receive; errno = No route to host
mount: nfsmount failed: Bad file descriptor
mount: Mounting 192.168.1.5:/share/hdd/data/dbox on /mnt/custom failed: Bad file descriptor
[CFSMounter] FS mount error: "mount -t nfs 192.168.1.5:/share/hdd/data/dbox/mp3 /mnt/mp3 -o rw,soft,udp,nolock,rsize=8192,wsize=8192"
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] registering as event client
[neutrino] initialized everything
PES, queue 0 normal.
avia_gt_core: masking unhandled irq reg 1 bit 15
[timeThread] - 21.11.2006 00:42:38, tim: Tue Nov 21 00:42:38 2006
[timeThread] Time set via DVB, going to sleep for 1800 seconds.
mount: RPC: Unable to receive; errno = No route to host
mount: nfsmount failed: Bad file descriptor
mount: Mounting 192.168.1.5:/share/hdd/data/dbox/mp3 on /mnt/mp3 failed: Bad file descriptor
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3)
[sectionsd] readNbytes: received POLLERR
DieMade
Oberlamer, Administrator & Supernanny
Beiträge: 10532
Registriert: Samstag 13. Juli 2002, 10:49

Beitrag von DieMade »

Vermutlich Ethernet-Transceiver defekt.
There are 10 types of people in the world: those who know binary and those who don't
HaeS
Neugieriger
Neugieriger
Beiträge: 18
Registriert: Sonntag 5. September 2004, 14:42

Beitrag von HaeS »

das heisst für mich neue Box kaufen oder kann man den ohne größere Umstände reparieren?
DieMade
Oberlamer, Administrator & Supernanny
Beiträge: 10532
Registriert: Samstag 13. Juli 2002, 10:49

Beitrag von DieMade »

"Man" kann. Kostenpunkt ~45 Euro

http://www.hallenberg.com
http://www.eifelshop.biz