Durch flashen kann man keine Box schrotten.
Und Du kannst immer noch nicht im Wiki suchen: http://wiki.tuxbox-cvs.sourceforge.net/Silicon_Bugs
Wenn Du die Anleitung oben genau befolgst, klappt das auch. Wenn nicht, liegt es an Windows. Nebenbei solltest Du nur auf den Flashassistenten achten. Was im Bootmanager steht ist irrelevant bei der Methode. Box und PC müssen aber über Netzwerk und Nullmodem verbunden sein. Und besser alle anderen Netzwerkadapter abschalten (deaktivieren). Und Firewall und ähnliches Sicherheitsgedöns abschalten oder (z.B. bei Produkten von Symantec) besser deinstallieren.
cu
Jens
Keine Sender nach Umbau
-
mariooo
- Neugieriger
- Beiträge: 15
- Registriert: Samstag 3. Februar 2007, 13:20
ich habe jetz eine weitere halbe stunde durlaufen lassen und der Flash assistent fängt immer wieder von vorne an
... der Bootlog (vom Flashassistenten kopiert
Wdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> seteth
ethaddr 0x1001ffe3
ethaddr: 00:50:9c:16:dc:ad
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.1, My IP 192.168.0.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140008
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.6 (Tuxbox) (Jan 8 2007 - 22:58:00)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: *##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: *####################################
Bytes transferred = 179877 (2bea5 hex)
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit
Size: 8192 kB in 71 Sectors
Sector Start Addresses:
10000000 (RO) 10004000 (RO) 10008000 (RO) 1000C000 (RO)
10010000 (RO) 10014000 (RO) 10018000 (RO) 1001C000 (RO)
10020000 (RO) 10040000 (RO) 10060000 (RO) 10080000 (RO)
100A0000 (RO) 100C0000 (RO) 100E0000 (RO) 10100000 (RO)
10120000 (RO) 10140000 (RO) 10160000 (RO) 10180000 (RO)
101A0000 (RO) 101C0000 (RO) 101E0000 (RO) 10200000 (RO)
10220000 (RO) 10240000 (RO) 10260000 (RO) 10280000 (RO)
102A0000 (RO) 102C0000 (RO) 102E0000 (RO) 10300000 (RO)
10320000 (RO) 10340000 (RO) 10360000 (RO) 10380000 (RO)
103A0000 (RO) 103C0000 (RO) 103E0000 (RO) 10400000 (RO)
10420000 (RO) 10440000 (RO) 10460000 (RO) 10480000 (RO)
104A0000 (RO) 104C0000 (RO) 104E0000 (RO) 10500000 (RO)
10520000 (RO) 10540000 (RO) 10560000 (RO) 10580000 (RO)
105A0000 (RO) 105C0000 (RO) 105E0000 (RO) 10600000 (RO)
10620000 (RO) 10640000 (RO) 10660000 (RO) 10680000 (RO)
106A0000 (RO) 106C0000 (RO) 106E0000 (RO) 10700000 (RO)
10720000 (RO) 10740000 (RO) 10760000 (RO) 10780000 (RO)
107A0000 (RO) 107C0000 (RO) 107E0000 (RO)
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
##
Bytes transferred = 675073 (a4d01 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 675009 Bytes = 659.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
<0>Rebooting in 180 seconds..￾￾debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: WATCHDOG RESET
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> seteth
ethaddr 0x1001ffe3
ethaddr: 00:50:9c:16:dc:ad
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.1, My IP 192.168.0.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140008
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.6 (Tuxbox) (Jan 8 2007 - 22:58:00)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: *##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: *####################################
Bytes transferred = 179877 (2bea5 hex)
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit
Size: 8192 kB in 71 Sectors
Sector Start Addresses:
10000000 (RO) 10004000 (RO) 10008000 (RO) 1000C000 (RO)
10010000 (RO) 10014000 (RO) 10018000 (RO) 1001C000 (RO)
10020000 10040000 10060000 10080000
100A0000 100C0000 100E0000 10100000
10120000 10140000 10160000 10180000
101A0000 101C0000 101E0000 10200000
10220000 10240000 10260000 10280000
102A0000 102C0000 102E0000 10300000
10320000 10340000 10360000 10380000
103A0000 103C0000 103E0000 10400000
10420000 10440000 10460000 10480000
104A0000 104C0000 104E0000 10500000
10520000 10540000 10560000 10580000
105A0000 105C0000 105E0000 10600000
10620000 10640000 10660000 10680000
106A0000 106C0000 106E0000 10700000
10720000 10740000 10760000 10780000
107A0000 107C0000 107E0000
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
##
Bytes transferred = 675073 (a4d01 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 675009 Bytes = 659.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Looking up port of RPC 100005/1 on 192.168.0.1
------ Zusatzinformationen ------
Gewählter Netzwerkadapter: 3Com 3C910 Integrated Fast Ethernet Controller (3CSOHO100B-TX Compatible) - Paketplaner-Miniport (2)
IP-Adresse des Netzwerkadapters: 192.168.0.1
IP-Adresse die die dbox bekommt: 192.168.0.202
Comport: Kommunikationsanschluss (COM1)
Betriebssystem: Microsoft Windows XP Professional Service Pack 2 (Build 2600)
CPU 1: Intel(R) Pentium(R) 4 CPU 2.40GHz @ 2400 MHz
Dateiname des Images: original.img
Imagetyp: Zwei Flashs
DBOX-IFA Version: 2.3
------ Powered by http://www.dboxservice-hallenberg.de ------
... der Bootlog (vom Flashassistenten kopiert
Wdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> seteth
ethaddr 0x1001ffe3
ethaddr: 00:50:9c:16:dc:ad
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.1, My IP 192.168.0.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140008
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.6 (Tuxbox) (Jan 8 2007 - 22:58:00)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: *##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: *####################################
Bytes transferred = 179877 (2bea5 hex)
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit
Size: 8192 kB in 71 Sectors
Sector Start Addresses:
10000000 (RO) 10004000 (RO) 10008000 (RO) 1000C000 (RO)
10010000 (RO) 10014000 (RO) 10018000 (RO) 1001C000 (RO)
10020000 (RO) 10040000 (RO) 10060000 (RO) 10080000 (RO)
100A0000 (RO) 100C0000 (RO) 100E0000 (RO) 10100000 (RO)
10120000 (RO) 10140000 (RO) 10160000 (RO) 10180000 (RO)
101A0000 (RO) 101C0000 (RO) 101E0000 (RO) 10200000 (RO)
10220000 (RO) 10240000 (RO) 10260000 (RO) 10280000 (RO)
102A0000 (RO) 102C0000 (RO) 102E0000 (RO) 10300000 (RO)
10320000 (RO) 10340000 (RO) 10360000 (RO) 10380000 (RO)
103A0000 (RO) 103C0000 (RO) 103E0000 (RO) 10400000 (RO)
10420000 (RO) 10440000 (RO) 10460000 (RO) 10480000 (RO)
104A0000 (RO) 104C0000 (RO) 104E0000 (RO) 10500000 (RO)
10520000 (RO) 10540000 (RO) 10560000 (RO) 10580000 (RO)
105A0000 (RO) 105C0000 (RO) 105E0000 (RO) 10600000 (RO)
10620000 (RO) 10640000 (RO) 10660000 (RO) 10680000 (RO)
106A0000 (RO) 106C0000 (RO) 106E0000 (RO) 10700000 (RO)
10720000 (RO) 10740000 (RO) 10760000 (RO) 10780000 (RO)
107A0000 (RO) 107C0000 (RO) 107E0000 (RO)
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
##
Bytes transferred = 675073 (a4d01 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 675009 Bytes = 659.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
<0>Rebooting in 180 seconds..￾￾debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: WATCHDOG RESET
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> seteth
ethaddr 0x1001ffe3
ethaddr: 00:50:9c:16:dc:ad
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.1, My IP 192.168.0.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140008
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.6 (Tuxbox) (Jan 8 2007 - 22:58:00)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: *##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: *####################################
Bytes transferred = 179877 (2bea5 hex)
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit
Size: 8192 kB in 71 Sectors
Sector Start Addresses:
10000000 (RO) 10004000 (RO) 10008000 (RO) 1000C000 (RO)
10010000 (RO) 10014000 (RO) 10018000 (RO) 1001C000 (RO)
10020000 10040000 10060000 10080000
100A0000 100C0000 100E0000 10100000
10120000 10140000 10160000 10180000
101A0000 101C0000 101E0000 10200000
10220000 10240000 10260000 10280000
102A0000 102C0000 102E0000 10300000
10320000 10340000 10360000 10380000
103A0000 103C0000 103E0000 10400000
10420000 10440000 10460000 10480000
104A0000 104C0000 104E0000 10500000
10520000 10540000 10560000 10580000
105A0000 105C0000 105E0000 10600000
10620000 10640000 10660000 10680000
106A0000 106C0000 106E0000 10700000
10720000 10740000 10760000 10780000
107A0000 107C0000 107E0000
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
##
Bytes transferred = 675073 (a4d01 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 675009 Bytes = 659.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Looking up port of RPC 100005/1 on 192.168.0.1
------ Zusatzinformationen ------
Gewählter Netzwerkadapter: 3Com 3C910 Integrated Fast Ethernet Controller (3CSOHO100B-TX Compatible) - Paketplaner-Miniport (2)
IP-Adresse des Netzwerkadapters: 192.168.0.1
IP-Adresse die die dbox bekommt: 192.168.0.202
Comport: Kommunikationsanschluss (COM1)
Betriebssystem: Microsoft Windows XP Professional Service Pack 2 (Build 2600)
CPU 1: Intel(R) Pentium(R) 4 CPU 2.40GHz @ 2400 MHz
Dateiname des Images: original.img
Imagetyp: Zwei Flashs
DBOX-IFA Version: 2.3
------ Powered by http://www.dboxservice-hallenberg.de ------
-
mariooo
- Neugieriger
- Beiträge: 15
- Registriert: Samstag 3. Februar 2007, 13:20
ich habe jetz eine weitere halbe stunde durlaufen lassen und der Flash assistent fängt immer wieder von vorne an
... der Bootlog (vom Flashassistenten kopiert
Wdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> seteth
ethaddr 0x1001ffe3
ethaddr: 00:50:9c:16:dc:ad
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.1, My IP 192.168.0.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140008
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.6 (Tuxbox) (Jan 8 2007 - 22:58:00)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: *##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: *####################################
Bytes transferred = 179877 (2bea5 hex)
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit
Size: 8192 kB in 71 Sectors
Sector Start Addresses:
10000000 (RO) 10004000 (RO) 10008000 (RO) 1000C000 (RO)
10010000 (RO) 10014000 (RO) 10018000 (RO) 1001C000 (RO)
10020000 (RO) 10040000 (RO) 10060000 (RO) 10080000 (RO)
100A0000 (RO) 100C0000 (RO) 100E0000 (RO) 10100000 (RO)
10120000 (RO) 10140000 (RO) 10160000 (RO) 10180000 (RO)
101A0000 (RO) 101C0000 (RO) 101E0000 (RO) 10200000 (RO)
10220000 (RO) 10240000 (RO) 10260000 (RO) 10280000 (RO)
102A0000 (RO) 102C0000 (RO) 102E0000 (RO) 10300000 (RO)
10320000 (RO) 10340000 (RO) 10360000 (RO) 10380000 (RO)
103A0000 (RO) 103C0000 (RO) 103E0000 (RO) 10400000 (RO)
10420000 (RO) 10440000 (RO) 10460000 (RO) 10480000 (RO)
104A0000 (RO) 104C0000 (RO) 104E0000 (RO) 10500000 (RO)
10520000 (RO) 10540000 (RO) 10560000 (RO) 10580000 (RO)
105A0000 (RO) 105C0000 (RO) 105E0000 (RO) 10600000 (RO)
10620000 (RO) 10640000 (RO) 10660000 (RO) 10680000 (RO)
106A0000 (RO) 106C0000 (RO) 106E0000 (RO) 10700000 (RO)
10720000 (RO) 10740000 (RO) 10760000 (RO) 10780000 (RO)
107A0000 (RO) 107C0000 (RO) 107E0000 (RO)
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
##
Bytes transferred = 675073 (a4d01 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 675009 Bytes = 659.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
<0>Rebooting in 180 seconds..￾￾debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: WATCHDOG RESET
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> seteth
ethaddr 0x1001ffe3
ethaddr: 00:50:9c:16:dc:ad
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.1, My IP 192.168.0.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140008
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.6 (Tuxbox) (Jan 8 2007 - 22:58:00)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: *##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: *####################################
Bytes transferred = 179877 (2bea5 hex)
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit
Size: 8192 kB in 71 Sectors
Sector Start Addresses:
10000000 (RO) 10004000 (RO) 10008000 (RO) 1000C000 (RO)
10010000 (RO) 10014000 (RO) 10018000 (RO) 1001C000 (RO)
10020000 10040000 10060000 10080000
100A0000 100C0000 100E0000 10100000
10120000 10140000 10160000 10180000
101A0000 101C0000 101E0000 10200000
10220000 10240000 10260000 10280000
102A0000 102C0000 102E0000 10300000
10320000 10340000 10360000 10380000
103A0000 103C0000 103E0000 10400000
10420000 10440000 10460000 10480000
104A0000 104C0000 104E0000 10500000
10520000 10540000 10560000 10580000
105A0000 105C0000 105E0000 10600000
10620000 10640000 10660000 10680000
106A0000 106C0000 106E0000 10700000
10720000 10740000 10760000 10780000
107A0000 107C0000 107E0000
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
##
Bytes transferred = 675073 (a4d01 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 675009 Bytes = 659.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Looking up port of RPC 100005/1 on 192.168.0.1
------ Zusatzinformationen ------
Gewählter Netzwerkadapter: 3Com 3C910 Integrated Fast Ethernet Controller (3CSOHO100B-TX Compatible) - Paketplaner-Miniport (2)
IP-Adresse des Netzwerkadapters: 192.168.0.1
IP-Adresse die die dbox bekommt: 192.168.0.202
Comport: Kommunikationsanschluss (COM1)
Betriebssystem: Microsoft Windows XP Professional Service Pack 2 (Build 2600)
CPU 1: Intel(R) Pentium(R) 4 CPU 2.40GHz @ 2400 MHz
Dateiname des Images: original.img
Imagetyp: Zwei Flashs
DBOX-IFA Version: 2.3
------ Powered by http://www.dboxservice-hallenberg.de ------
auch mehrere Images habe ich ausprobiert und auch alle Firewalls abgeschaltet und auch alle netzwerkverbindungen gekappt außer die zu dbox .... - die Dbox selber zeigt an ... lade Software ( auf dem Display) und am fernseher ist ein bild von hallenberg zu sehen ....
... der Bootlog (vom Flashassistenten kopiert
Wdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> seteth
ethaddr 0x1001ffe3
ethaddr: 00:50:9c:16:dc:ad
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.1, My IP 192.168.0.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140008
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.6 (Tuxbox) (Jan 8 2007 - 22:58:00)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: *##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: *####################################
Bytes transferred = 179877 (2bea5 hex)
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit
Size: 8192 kB in 71 Sectors
Sector Start Addresses:
10000000 (RO) 10004000 (RO) 10008000 (RO) 1000C000 (RO)
10010000 (RO) 10014000 (RO) 10018000 (RO) 1001C000 (RO)
10020000 (RO) 10040000 (RO) 10060000 (RO) 10080000 (RO)
100A0000 (RO) 100C0000 (RO) 100E0000 (RO) 10100000 (RO)
10120000 (RO) 10140000 (RO) 10160000 (RO) 10180000 (RO)
101A0000 (RO) 101C0000 (RO) 101E0000 (RO) 10200000 (RO)
10220000 (RO) 10240000 (RO) 10260000 (RO) 10280000 (RO)
102A0000 (RO) 102C0000 (RO) 102E0000 (RO) 10300000 (RO)
10320000 (RO) 10340000 (RO) 10360000 (RO) 10380000 (RO)
103A0000 (RO) 103C0000 (RO) 103E0000 (RO) 10400000 (RO)
10420000 (RO) 10440000 (RO) 10460000 (RO) 10480000 (RO)
104A0000 (RO) 104C0000 (RO) 104E0000 (RO) 10500000 (RO)
10520000 (RO) 10540000 (RO) 10560000 (RO) 10580000 (RO)
105A0000 (RO) 105C0000 (RO) 105E0000 (RO) 10600000 (RO)
10620000 (RO) 10640000 (RO) 10660000 (RO) 10680000 (RO)
106A0000 (RO) 106C0000 (RO) 106E0000 (RO) 10700000 (RO)
10720000 (RO) 10740000 (RO) 10760000 (RO) 10780000 (RO)
107A0000 (RO) 107C0000 (RO) 107E0000 (RO)
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
##
Bytes transferred = 675073 (a4d01 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 675009 Bytes = 659.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
<0>Rebooting in 180 seconds..￾￾debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: WATCHDOG RESET
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> seteth
ethaddr 0x1001ffe3
ethaddr: 00:50:9c:16:dc:ad
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.1, My IP 192.168.0.202
debug: Sending TFTP-request for file C/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140008
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
U-Boot 1.1.6 (Tuxbox) (Jan 8 2007 - 22:58:00)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-lcd'.
Load address: 0x100000
Loading: *##
Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'C/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'logo-fb'.
Load address: 0x100000
Loading: *####################################
Bytes transferred = 179877 (2bea5 hex)
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1 0
Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit
Size: 8192 kB in 71 Sectors
Sector Start Addresses:
10000000 (RO) 10004000 (RO) 10008000 (RO) 1000C000 (RO)
10010000 (RO) 10014000 (RO) 10018000 (RO) 1001C000 (RO)
10020000 10040000 10060000 10080000
100A0000 100C0000 100E0000 10100000
10120000 10140000 10160000 10180000
101A0000 101C0000 101E0000 10200000
10220000 10240000 10260000 10280000
102A0000 102C0000 102E0000 10300000
10320000 10340000 10360000 10380000
103A0000 103C0000 103E0000 10400000
10420000 10440000 10460000 10480000
104A0000 104C0000 104E0000 10500000
10520000 10540000 10560000 10580000
105A0000 105C0000 105E0000 10600000
10620000 10640000 10660000 10680000
106A0000 106C0000 106E0000 10700000
10720000 10740000 10760000 10780000
107A0000 107C0000 107E0000
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
##
Bytes transferred = 675073 (a4d01 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 675009 Bytes = 659.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Looking up port of RPC 100005/1 on 192.168.0.1
------ Zusatzinformationen ------
Gewählter Netzwerkadapter: 3Com 3C910 Integrated Fast Ethernet Controller (3CSOHO100B-TX Compatible) - Paketplaner-Miniport (2)
IP-Adresse des Netzwerkadapters: 192.168.0.1
IP-Adresse die die dbox bekommt: 192.168.0.202
Comport: Kommunikationsanschluss (COM1)
Betriebssystem: Microsoft Windows XP Professional Service Pack 2 (Build 2600)
CPU 1: Intel(R) Pentium(R) 4 CPU 2.40GHz @ 2400 MHz
Dateiname des Images: original.img
Imagetyp: Zwei Flashs
DBOX-IFA Version: 2.3
------ Powered by http://www.dboxservice-hallenberg.de ------
auch mehrere Images habe ich ausprobiert und auch alle Firewalls abgeschaltet und auch alle netzwerkverbindungen gekappt außer die zu dbox .... - die Dbox selber zeigt an ... lade Software ( auf dem Display) und am fernseher ist ein bild von hallenberg zu sehen ....
-
mariooo
- Neugieriger
- Beiträge: 15
- Registriert: Samstag 3. Februar 2007, 13:20