habe ich schon einige male kontrolliert, das IDE-Kabel habe ich auch
getauscht und auch ein anderes Netzgerät ausprobiert. Das Flachbandkabel
habe ich durchgemessen und ist auch in Ordnung. Leider bekomme ich
immer die Fehlermeldung "hda: lost interrupt" (siehe bootlog).
Ein zweite Festplatte steht mir leider nicht zu Verfügung, die
vorhandene funktioniert am PC jedoch einwandfrei.
Was könnte ich noch überprüfen? Ist das Interface defekt?
Gruß
Asterix
Code: Alles auswählen
0debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.0 mID 02
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-1c.8e.38.08.00.00-03
debug: HWrev 01 FPrev 0.30
debug: B/Ex/Fl(MB) 32/00/08
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/philips-dbox2/kernel/os in Flash-FS
debug: Got Block #0040
will verify ELF image, start= 0x800000, size= 158020
verify sig: 262
Branching to 0x40000
U-Boot 1.1.4 (Tuxbox) (Aug 7 2006 - 21:15:08)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-C
Board: DBOX2, Philips, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 694133 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 694069 Bytes = 677.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.34.1-dbox2 (vom Jtg-Team) (gcc version 3.4.6) #1 Mo 19. Feb 2
2:03:30 CET 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rootfstype=squashfs
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30780k available (1180k kernel code, 348k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:2d:08:55
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabledDF: 66.76 BogoMIPS
Creating 6 MTD partitions on "D-Box 2 flash memory": mID 02
debug: feID 00 e
0x00000000-0x00020000 : "BR bootloader" fpID 52 dsID 01-1c.8e.38.08.00.00-
0x00020000-0x00040000 : "FLFS (U-Boot)"
debug: HWrev 01 FPrev 0.30
0x00040000-0x006a0000 : "root (SquashFS)"B) 32/00/08
db
0x006a0000-0x00800000 : "var (JFFS2)"TP/TFTP bootstrap loader (v0.3)
0x00020000-0x00800000 : "Flash without bootloader"ansmitting BOOTP request via broadcast
0x00000000-0x00800000 : "Complete Flash": Given up BOOTP/TFTP boot
Linux video capture interface: v1.00
Flash-FS bootstrap load
mice: PS/2 mouse device common for all miceound Flash-FS superblock version 3.1
NET4: Linux TCP/IP 1.0 for NET4.0nd file /root/platform/philips-db
IP Protocols: ICMP, UDP, TCP
C
VFS: Mounted root (squashfs filesystem) readonly.Cache
Mounted devfs on /devOX2, Philips, BMon V1
Freeing unused kernel memory: 60k init Watchdog enabled
Starting pid 10, console /dev/console: '/etc/init.d/rcS'multi-calB
Scanning JFFS2 FS: . done.
Starting the automounter
LCD: ready
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4: serial
Net: SCC ETHERNET
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xxon ttyS0
3: Console on framebuffer
hda: SAMSUNG SP1213N, ATA DISK drive63 sectors
##
ide0 at 0x010-0x017,0x04e on irq 47
Image
hda: attached ide-disk driver.
Image Type: PowerPC
hda: host protected area => 1ressed)
Thu Jan 1 12:00:00 CET 1970
Data Size:
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Load Address: 00000000
route: SIOC[ADD|DEL]RT: Network is unreachable
Verifying Checksum ... OK
[i2c-8xx]: mpc 8xx i2c initssing Kernel Image ... O
[i2c-8xx]: adapt
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $y = 247500000/60
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
m8xx_wdt: keep-alive trigger ins
avia_av: AVIA500 sptsfix is off
avia_av_core: Starting avia_av_wdt thread.x25
Cali
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
Memory: 30780k available (1180k kernel cod
Page-cache hash table entries: 8192 (
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
POSIX conformance testing by UNIFIX
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $wansea University Computer Society NET3.039
avia_gt_ucode: loaded ucode vB107izing RT netlink socket
avia_gt_ucode: ucode section filters disabled.
devfs: v1.12c (20020818) Richard Gooch (r
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
CPM UART driver version 0.04
avia_gt_pcm_set_rate(44100)0280 is on SMC1 using BRGtt
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
pty: 256 Unix98 ptys configured
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $:2d:08:55
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $sh driver (size->0x800000 mem->0
avia_gt_gv: set_input_mode (mode=2)00 : "BR bootloader"
avia_gt_gv: set_input_size (width=720, height=576)LFS (U-Boot)"
avia_gt_gv: set_input_mode (mode=2)uashFS)"
avia_gt_gv: set_input_size (width=720, height=576)"
0x00020000-
Console: switching to colour frame buffer device 82x32
0x00000000-0x008000
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer deviceLinux video capture interface: v1.00
avia_av_core: Starting av
IP: routing cache hash table of 512 buckets, 4Kbytes
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $ured (established 2048 bind 4096)
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $4.0.
VFS: Mount
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
Mounted devfs on /dev
Freei
avia_gt_pcm_set_rate(44100) init
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $S'multi-cal
DVB: registering frontend 0:0 (TDA8044H QPSK Demodulator)...rm Multi-Platform E-IDE driver Revision: 7
dboxide: address space of DBox2 ID
[sectionsd] Caching max 5000 events
[sectionsd] Caching 14 daysrface ide0...
[sectionsd] Events are old 60min after their end time
ide0 at 0x010-0x01
/var/tuxbox/config/epgfilter.xml: No such file or directorytached ide-disk driver.
hda:
$Id: zapit.cpp,v 1.392 2007/02/07 21:36:53 houdini Exp $ Jan 1 12:00:00 CET 1970
ev
/tmp/currentservices.xml: No such file or directory $
[camd] ca system i
[controld]: ROUTEVIDEO v1 = 1 a1 = 1 v2 = 1 a2 = 1 v3 = 1 a3 = 1 fblk=1
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
SET VSW: 0 1
SET VSW: 1 1
DVB: r
SET VSW: 2 1w adapter (C
[controld] setting VideoFormat to auto
[yhttpd] Webserver nhttpd/3.1.2 (yhttpd_core/1.2.0)ed DVB i2c bridge to PowerPC 8xx I2C adapter
[LCDFONT] initializing core...hda: lost interrupt
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:3
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)v: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)v: AVIA500 sptsfix is off
avia_av_core
avia_gt_enx: $Id: avia
/bin/neutrino) 2003/09/30 05:
[neutrino] frameBuffer Instance created
812k video memcel: $Id: avia
avia_gt_gv: set_input_mode (mode=2)35 obi Exp $
avia_gt_gv: set_input_size (width=720, height=576)via_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26
[neutrino] Software update enabled
[neutrino] enable flash
avia_gt_ucode: loaded
avia_gt_gv: $Id: avia_gt_gv.c,v 1.
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core..._size (width=720, height=576)
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular): avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)t_pcm_set_rate(44100)
avia_gt_captur
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...t_pig.c,v 1.40 2003/09/30 05:45:35
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Req
loading locales: scandir: No such file or directory
avia_gt_fb
[neutrino] received 17 sats.54 2004/03/17 18:42:18 zwe
[neutrino] registering as event client
[controld] setting VideoFormat to auto
avi
[neutrino] initialized everything, height=576)
zap failed!
[sectionsd] getUTC: read: Connection timed out
avia_gt_gv: se
hda: lost interrupt720, height=576)
[sectionsd] getUTC: read: Connection timed out
avia_gt_gv: set_input_mode (mode=2)
hda: lost interrupt
avia_gt_gv: s
[sectionsd] getUTC: read: Connection timed out
Conso
hda: lost interruptour f
hda: lost interrupt
avia_gt_
p5<3>hda: lost interrupt
p6[sectionsd] getUTC: read: Connection timed out
<3>hda: lost interrupt
p7<3>hda: lost interrupt
p8<3>hda: lost interrupt
p9[sectionsd] getUTC: read: Connection timed out
zapit shot down :)
Going to halt system now ...
Starting pid 153, console /dev/console: '/etc/init.d/halt'
STV6412 found
SET VSW: 2 3
SET VSW: 1 2
Unmounting 'tmpfs' on '/tmp'
umount: cannot umount /tmp: Device or resource busy
Unmounting 'jffs2' on '/var'
Ready to shutdown system...
The system is going down NOW !![yhttpd] !!! SIGNAL !!! :15!
[yhttpd] No special SIGNAL-Handler:15!
[yhttpd] stop requested......
Sending SIGKILL to all processes.
Requesting system halt.
hda: lost interrupt
p10<6>flushing ide devices: hda <3>hda: lost interrupt
p119
