Kein Bild und Ton am Fernseher

[Kdschmie]

Hallo,
ich habe eine D-Box2 von Sagem geschenkt bekommen. 2xAMD, Avia 600
für Kabel. Auf der Box ist ein Yadi-Image, doch ich bekommen kein Bild und Ton am Fernseher. Auf den Display wird der Kanal angezeigt.

Ich habe schon festgestellt, dass 9 Volt-Pin ( zum aufheben des Schreibschutzes nur 2,25 Volt anliegen.

Kann mir jemand sagen, was ich noch prüfen kann?

[Tommy]

Was willst Du mit dem Schreibschutz wenn die Box schon im Debug ist

Mach lieber ein Bootlog

[Gorcon]

Mal einen Suchlauf gemacht?

Gruß Gorcon

[Kdschmie]

Hallo, da ich ja wusste, das an diesem Pin 9 Volt anliegen müssen, habe ich dort nur mal gemessen.
Hier ist das Bootlog:

debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.0 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-e9.4b.85.07.00.00-39
debug: HWrev 41 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0040

will verify ELF image, start= 0x800000, size= 160940
verify sig: 263
Branching to 0x40000


U-Boot 1.1.2 (Tuxbox) (May 26 2005 - 16:37:05)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 674386 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 674322 Bytes = 658.5 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.32-dbox2 (ImageTeam@yadi.org) (gcc version 3.4.4) #2 So Jun 25
15:17:53 CEST 2006
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2580)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30816k available (1148k kernel code, 344k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:39:1f:c2
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00680000 : "root (squashfs)"
0x00680000-0x007e0000 : "var (jffs2)"
0x007e0000-0x00800000 : "flfs (u-boot)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'lti-call
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Oops: kernel access of bad area, sig: 11
NIP: C00AB9D4 XER: 00000000 LR: C389B60C SP: C1C8DE30 REGS: c1c8dd80 TRAP: 0300
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 00000024, DSISR: C0000000
TASK = c1c8c000[23] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C389B60C C1C8DE30 C1C8C000 C389D7DC C389D7BA 00000007 00000016 C1C8C03C
GPR08: 00000000 00000004 0000003F C00AB9BC 24008042 1006F740 00000001 10050000
GPR16: 00000001 10060000 100760F8 10075E38 00009032 C1C8DEA0 C1BC0000 100863D0
GPR24: C1C5A280 00000003 C389F000 C013D5C8 C38A0000 00000007 00000000 00000000
Call backtrace:
C389C3D8 C389B60C C389C9F8 C0010FF4 C000285C 1001DDD8 10003C48
10003CC4 0FEC3D1C 00000000
Segmentation fault
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 1).
Detected STB:
Vendor: Sagem
Model: D-BOX2
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
i2c-core.o: driver DBox2-CAM registered.
i2c-core.o: client [DBox2-CAM] registered to adapter [PowerPC 8xx I2C adapter](p
os. 2).
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
i2c-core.o: client [DVB I2C bridge] registered to adapter [PowerPC 8xx I2C adapt
er](pos. 3).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Thu Jan 1 01:00:00 CET 1970
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
DVB: registering frontend 0:0 (Atmel AT76C651A with TUA6010XS)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
$Id: chkIVersion.cpp,v 1.12 2005/12/21 22:23:20 mogway Exp $
Yadi Snapshot vom 25.06.2006 13:51 - Image-Version 2.1.0.11
Networkcfg eth0: 192.168.1.103/255.255.255.0 gw 192.168.1.1 ns 192.168.1.1
Startmode: Neutrino - HWS: off
Starting pid 99, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.227 2006/06/
08 20:19:32 houdini Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Events are old 60min after their end time
[camd] ca system id: 1722
$Id: zapit.cpp,v 1.389 2006/06/08 20:17:58 houdini Exp $
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
/tmp/currentservices.xml: No such file or directory
$Id: controld.cpp,v 1.123 2006/06/18 10:39:40 barf Exp $

[controld] Boxtype detected: (3, Sagem D-BOX2)
[controld] /dev/dbox/avs0: No such file or directory
[controld] /dev/dbox/avs0: No such file or directory
[controld]: ROUTEVIDEO v1 = 0 a1 = 0 v2 = 0 a2 = 0 fblk=1
[controld] /dev/dbox/avs0: No such file or directory
[controld] /dev/dbox/avs0: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[camd] no card is in slot #2
[camd] no card is in slot #1
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] registering as event client
[neutrino] initialized everything
zap failed!
[sectionsd] getUTC: read: Connection timed out

[Tommy]

komisch irgendwie häuft sich

Oops: kernel access of bad area, sig: 11

hier im Board. Oder ist das immer dieselbe Box

[Kdschmie]

Hallo Tommy, es ist mit Sicherheit eine andere Box.
Hast Du ne Ahnung ,was es ist?

[seife]

Es sieht so aus, als würde der Kernel beim Laden des avs-Moduls crashen. Was wiederum auf einen defekt des AV-Switch-Chips hindeuten könnte.

[Kdschmie]

Danke für die schnelle Antwort.
Was würde so eine Reparatur ca. kosten?

[seife]

Google? "dbox2 reparatur"