Triple Dragon - NeutrinoHD Buildsystem

[seife]

Was hast du denn vor "make bootstrap" gemacht?

Alles angeben, genau bitte.

[seife]

Was hast du denn genau gemacht (vom auschecken über die verschiedenen Targets)?

[Nenso]

bin nach der anleitung hier im board vorgegangen, (http://www.tuxbox-cvs.sourceforge.net/f ... 62&t=49203)
hat auch alles ohne fehler hingehauen bis dahin bin noob in diesen sachen.

ich editier mal bissel, so kann ich das ja nicht stehen lassen ohne echte angaben wieso weshalb warum
nun weiß ich auch was du mit auschecken meinst (hoffe ich)

nutze debian squeeze 6.0.1

so das hab ich vorher installiert:
apt-get install git make subversion patch gcc bison flex texinfo automake libtool ncurses-dev pkg-config

ich habe das gemacht:
mkdir ~/neutrino-hd-td
cd ~/neutrino-hd-td
Anschließend checkt man das Build-System für die Triple Dragon aus
git clone git://gitorious.org/tripledragon-buildscripts/mainline.git
cd mainline
ln -s ~/tuxbox-archive download
config geändert:
FLAVOUR=neutrino-hd-tripledragon
make preqs
make crosstool
make bootstrap und da kommt der fehler den ich gepostet habe.

hoffe nun sind die infos besser, falls noch was fehlt reiche ich es gerne nach.

[Nenso]

noch als anhang:

Tool Checker for Tuxbox-CVS

automake >=1.7 : Installed! (Version: 1.11.1)
autoconf >=2.50 : Installed! (Version: tuning)
cvs : Installed!
svn : Installed!
libtool >=1.4.2 : Installed! (Version: 2.2.6b)
make >=3.79 : Installed! (Version: 3.81)
gettext >=0.12.1 : Installed! (Version: 0.18.1)
makeinfo : Installed!
tar : Installed!
bunzip2 : Installed!
gunzip : Installed!
patch : Installed!
infocmp : Installed!
g++ >=3.0 : Installed! (Version: 4.4.5)
bison : Installed!
flex : Installed!
pkg-config : Installed!
python : Installed!
wget : Installed!
yacc : Installed!
ncurses-devel : Installed!
zlib-devel : Installed!

[seife]

Falsch, das alte buildsystem ist nicht mehr maintained, und schon gar nicht für neutrino-hd.
Das ist hier auch das flasche Board für Fragen zur Tripledragon.
http://www.triple-dragon-fan.de/board/t ... eadid=3156

[vulcaneanu71]

Hello everybody!
I tried to install td_hd_neutrino_20120220 .bz2 on the second partition "sda2" (system partition 1) of HDD.
But the receiver locks itself on startup ...
I followed the steps:

First of all I installed the hdd in the correct way.
1) Go to osd menu-->system setup --> more system setup --> harddisk--> install --> initialise HDD -->now.... for to partinion the HDD;

2) Download td_hd_neutrino_20120220.tar.bz2 ( http://tuxbox.trale.de/ )

3) Clear the /mnt/hd/data directory.(telnet- "rm -rf /mnt/hd/data/*")

4) Upload td_hd_neutrino_20120220.tar.bz2 to /mnt/hd/data

5) Un-tar the archive...
cd /mnt/hd/data
tar -zxvf td_hd_neutrino_20120220.tar.bz2

6) Reboot and go into Bootmenu

7) Change Kernel Commandline to option 3. Save settings and reboot...

When starting up the receiver, based on the help of the PuTTY (--> COM1-->serial-->speed 115200), I receive the following message on the PC :


/ (C) MNC Ltd. Set-Top-Box \
\ BIOS 3.29 (2005/11/07) /
-------------------------------
\ .--. Serialnumber: Tripledragon-EU-0-170327161-S
|o_o | PowerPC at : 252 MHz, EBIU: 63 MHz, PVR: 41810952, VDEV: 0B
|:_/ | RAM config : B0: 2x32=64 MB, B1: 2x8=16 MB, [80 MB]
// \ \ Flash memory: Size: 8 MB, Manufacturer: 04, Type: 22D7
(| | ) Tunertype : DVB-S, Sat-Tuner BS2F7VZ0184
/'\_ _/`\ Ethernet : Chip 33, Revis. 91 (SMC91C11x)
\___)=(___/ Network : not initialised yet
Ethernet MAC: BADDAD26FC79, TD IP: 192.168.1.123, Host IP: 192.168.1.1
F-System: 0xFF9C0000, 0x480000 (4718592 Byte), VAR: 1769472 Byte / 27 sect
Kernel : 0xFFE40000, 0x197A00 (1669632 Byte / 26 sect), autostart
Main Bios-Menu
0 - Boot
R - Reset
S - Save config

B - Boot/Kernel Setup
E - Upgrade/Flash/Network
H - Hardware Setup
L - Loader Config
V - Video/Modulator Setup
->

loaded at: 00500000 00698178
relocated to: 00400000 00598178
board data at: 00596124 00596178
relocated to: 0040515C 004051B0
zimage at: 004058B1 00595D07
avail ram: 00599000 04000000

Linux/PPC load: console=ttyS1,115200 root=/dev/ide/host0/bus0/target0/lun0/part2 rw mtdparts=phys_mapped_flash:64k(conf),1728k(var),4718592(filesystem),1703936(kernel),128k(ppcboot)ro
Uncompressing Linux....
Now booting the kernel (misc-embedded)
Linux version 2.6.12 (flow@flownix) (gcc version 3.4.1) #396 Tue Oct 4 23:22:10 CEST 2005

machine: TRIPLEDRAGON STB
bi_s_version (bd_t struct's version) : 1.7
bi_r_version (bios/bootloader version): 3.29

bi_memsize : 0x04000000 (65)MBytes
bi_memsize1: 0x01000000 (16)MBytes
bi_enetaddr: ba:dd:ad:26:fc:79
bi_intfreq (CPU speed) : 0x0f053700 (252)Mhz
bi_busfreq (PLB clock) : 0x03c14dc0 (63)MHz
bi_tbfreq (SW timebase): 0x019bfcc0 (27)MHz
bi_opb_busfreq : 0x03c14dc0 (63)MHz
bi_iic_fast enable : [0] 0, [1] 0
flash_base : 0xff800000

MNC Ltd. DBx3000
http://www.mncltd.com
Built 1 zonelists
Kernel command line: console=ttyS1,115200 root=/dev/ide/host0/bus0/target0/lun0/part2 rw mtdparts=phys_mapped_flash:64k(conf),1728k(var),4718592(filesystem),1703936(kernel),128k(ppcboot)ro
PID hash table entries: 512 (order: 9, 8192 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 61312k available (2724k kernel code, 724k data, 88k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Squashfs 2.2 (released 2005/07/03) (C) 2002-2005 Phillip Lougher
Squashfs 2.2 includes LZMA decompression support
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 20) is a 16550A
ttyS1 at MMIO 0x0 (irq = 21) is a 16550A
ttyS2 at MMIO 0x0 (irq = 31) is a 16550A
io scheduler noop registered
io scheduler deadline registered
loop: loaded (max 8 devices)
smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <nico@cam.org>
eth0: SMC91C11xFD (rev 1) at c5056300 IRQ 28
eth0: Ethernet addr: ba:dd:ad:26:fc:79
eth0: PHY LAN83C183 (LAN91C111 Internal)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
physmap flash device: 800000 at ff800000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
phys_mapped_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
5 cmdlinepart partitions found on MTD device phys_mapped_flash
Creating 5 MTD partitions on "phys_mapped_flash":
0x00000000-0x00010000 : "conf"
0x00010000-0x001c0000 : "var"
0x001c0000-0x00640000 : "filesystem"
0x00640000-0x007e0000 : "kernel"
0x007e0000-0x00800000 : "ppcboot"
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
IBM IIC driver v3.1
ibm-iic0: using standard (100 kHz) mode
ibm-iic1: using standard (100 kHz) mode
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
STB04500 OCP IDE 2.74 - Built Oct 3 2005/12:18:01 for 2.6.12 (none debug)
hda: WDC WD1200JB-00REA0, ATA DISK drive
ide0 at 0xc505c1f8-0xc505c1ff,0xc505c1f6 on irq 25
hda: max request size: 1024KiB
hda: Host Protected Area detected.
current capacity is 234435439 sectors (120030 MB)
native capacity is 234441648 sectors (120034 MB)
hda: Host Protected Area disabled.
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(66)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
Root-NFS: No NFS server available, giving up.
VFS: Unable to mount root fs via NFS, trying floppy.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 88k init
init started: BusyBox v1.18.4 (tripledragon)
/etc/init.d/rcS: line 20: ldconfig: not found
starting /etc/init.d/S01mount ...
root FS is mounted rw, skipping filesystem check
starting /etc/init.d/S50hostname ...
starting /etc/init.d/S51networking ...
Configuring network interfaces... eth0: link down
udhcpc (v1.18.4) started
Sending discover...
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Sending discover...
Sending select for 192.168.1.163...
Lease of 192.168.1.163 obtained, lease time 43200
Starting ifplugd... .
starting /etc/init.d/S52syslogd ...
Jan 1 01:00:33 tripledragon syslog.info syslogd started: BusyBox v1.18.4
starting /etc/init.d/S54inetd ...
starting /etc/init.d/S55loadmodules ...
STB04500 TDCORE 2.07 - Built Oct 28 2005/14:57:11 for 2.6.12 (none debug)
tdav: no version for "os_call_irq_task" found: kernel tainted.
STB04500 TDAV 1.48 - Built Nov 16 2005/19:31:49 for 2.6.12 (none debug)
STB04500 TDPANEL 1.20 - Built Oct 28 2005/14:57:25 for 2.6.12 (none debug)
STB04500 TDTUNER 2.14 - Built Oct 28 2005/14:57:40 for 2.6.12 (none debug)
STB04500 TDCA 1.18 - Built Oct 28 2005/14:57:27 for 2.6.12 (none debug)
STB04500 TDCI 1.42 - Built Oct 28 2005/14:57:31 for 2.6.12 (none debug)
STB04500 TDGFX 1.40 - Built Oct 28 2005/14:57:35 for 2.6.12 (none debug)
STB04500 TDOSS 1.28 - Built Oct 28 2005/14:57:20 for 2.6.12 (none debug)
Jan 1 00:00:34 tripledragon daemon.info init: starting pid 283, tty '': '/etc/init.d/start'

Please press Enter to activate this console. [neutrino] frameBuffer Instance created
libtriple debug options can be set by exporting TRIPLE_DEBUG.
The following values (or bitwise OR combinations) are valid:
component: audio 0x01
component: video 0x02
component: demux 0x04
component: play 0x08
component: power 0x10
component: init 0x20
component: ca 0x40
component: record 0x80
all components: 0xff
[LT:00000000:init ] init_td_api begin, initialized=0, debug=0x00
DFB input converter thread starting...
modprobe: module uinput not found in modules.dep
modprobe: module evdev not found in modules.dep
DFB input thread: unable to open /dev/misc/uinput (No such file or directory)

Where am I wrong?

Please give details about my mistake!

Thanks!

[hannebamb(el)]

Hi,

Try to login via telnet to your receiver and enter

depmod -ae
reboot

After that it should work

Br

HB

[vulcaneanu71]

Vielen Dank!
Werde ich versuchen!