Ich verfolge dieses Forum nun schon ein ganzes Weilchen und habe auch für so ziemlich jedes Problem eine Lösung gefunden.
Diesmal benötige ich aber Hilfe.
Meine Nokia 2xI Avia500 SAT ist erfolgreich im Debug und das Flaschen usw. stellt alles kein Problem dar.
Was mir trotz aller Bemühungen nicht gelingt ist eine yadd ans laufen zu bekommen. Sowohl das aktuelle AlexW yadd als auch z.B. das yadd vom 30.06 laufen zwar i.R. problemlos bis zur GUI hoch; Bedienung alles so wie beim geflashten Image.
Allerdings scheint die Box beim Hochfahren nicht gänzlich/ausschließlich das "yadd-boot" zu verwenden, da bereits am Anfang des Bootvorgangs ein "kriselndes TV-Bild" erswcheint und im Hintergrund ist schwach das Startup-Bild des geflaschten(!) Startup-Logos zu erkennen. Ebenso zeigt das LCD das Start-Logo des geflashten(!) Images an!
Das COM-Terminal zeigt aber definitiv an, das das yadd geladen wird.
Nachdem die GUI (Neutrino) oben ist, habe ich ebenfalls "Sternenhimmel, Krisel". Die Kanalsuche findet keinerlei Sender.
Ucodes sind kopiert.
Und wie gesagt: mit den geflashten Image(s) bisher keine Probleme.
Wo liegt der Fehler?
Anbei der Log vom yadd 30.06:
---------------------------------------------------------------------------
**Adapter Desc: Realtek 8139-series PCI NIC
***MAC address: 00:E0:18:0E:36:21 Local IP: 192.168.123.100 (via Packet-Driver #1)
***BootP server started... Port 67
***TFTP server started... Port 69
BootP> Request from 00:50:9C:1F:96:DB (assuming that this is DBox).
BootP> Answer sent!
TFTP> Started TFTP-Transfer for "C:\yadd3006\tftpboot\ppcboot"...
TFTP> Transfer finished, sent 434 blocks
BootP> Answer sent!
TFTP> Non-BootP TFTP-transfer requested "C\yadd3006\tftpboot\logo-lcd"
TFTP> Started TFTP-Transfer for "C:\yadd3006\tftpboot\logo-lcd"...
TFTP> Transfer finished, sent 16 blocks
BootP> Answer sent!
TFTP> Non-BootP TFTP-transfer requested "C\yadd3006\tftpboot\logo-fb"
TFTP> Started TFTP-Transfer for "C:\yadd3006\tftpboot\logo-fb"...
TFTP> Transfer finished, sent 25 blocks
BootP> Answer sent!
TFTP> Non-BootP TFTP-transfer requested "C\yadd3006\tftpboot\kernel-cdk"
TFTP> Started TFTP-Transfer for "C:\yadd3006\tftpboot\kernel-cdk"...
TFTP> Transfer finished, sent 1274 blocks
BootP> Answer sent!
1 - mountd: mount: path: C/yadd3006/cdkroot/
---------------------------------------------------------------------------
.debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-42.a6.43.07.00.00-9b
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.123.100, My IP 192.168.123.122
debug: Sending TFTP-request for file C/yadd3006/tftpboot/ppcboot
will verify ELF image, start= 0x800000, size= 221853
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000
ppcboot 0.6.4 (Jun 30 2002 - 14:23:29)
Initializing...
CPU: PPC823ZTnnA at 67 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-1f-96-db
FLASH: 8 MB
LCD driver (KS0713) initialized
No LCD Logo in Flash , trying tftp
BOOTP broadcast 1
TFTP from server 192.168.123.100; our IP address is 192.168.123.122
Filename 'C/yadd3006/tftpboot/logo-lcd'.
Load address: 0x130000
Loading: ##
LCD logo at: 0x130000 (0x1FE11E0 bytes)
No FB Logo in Flash , trying tftp
BOOTP broadcast 1
TFTP from server 192.168.123.100; our IP address is 192.168.123.122
Filename 'C/yadd3006/tftpboot/logo-fb'.
Load address: 0x120000
Loading: ###
FB logo at: 0x0 (0x1FE11E0 bytes)
AVIA Frambuffer
Input: serial
Output: serial
Images:
1: cdk
2: yadd
3: debian
4: tiab
5: flash
Select image (1-5), other keys to stop autoboot: 0
BOOTP broadcast 1
TFTP from server 192.168.123.100; our IP address is 192.168.123.122
Filename 'C/yadd3006/tftpboot/kernel-cdk'.
Load address: 0x100000
Loading: #######################################################################
#########################################################
## Booting Linux kernel at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 652059 Bytes = 636 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.2 (Sinnlos98@ATHLON) (gcc version 2.95.3 20010315 (release)) #
4 Sun Jun 30 14:23:45 2002
Boot arguments: console=ttyS0 ip=bootp root=/dev/nfs rw nfsroot=192.168.123.100:
C/yadd3006/cdkroot/
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 ip=bootp root=/dev/nfs rw nfsroot=192.168.123
.100:C/yadd3006/cdkroot/
time_init: decrementer frequency = 251250000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x3000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.56 BogoMIPS
Memory: 30284k available (1256k kernel code, 560k data, 68k init, 0k highmem)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Starting kswapd v1.8
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
block: queued sectors max/low 20018kB/6672kB, 64 slots per queue
loop: enabling 8 loop devices
eth0: CPM ENET Version 0.2, 00:50:9c:1f:96:db
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR Bootloader"
0x00020000-0x000c0000 : "idxfs"
0x000c0000-0x00160000 : "var ( JFFS2 )"
0x00160000-0x00760000 : "root ( CramFS )"
0x00760000-0x00800000 : "ppcboot"
0x00020000-0x00800000 : "GesamtesFlashohneBL"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
Sending BOOTP requests.... OK
IP-Config: Got BOOTP answer from 192.168.123.100, my address is 192.168.123.122
IP-Config: Guessing netmask 255.255.255.0
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
devfs: v0.102 (20000622) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Looking up port of RPC 100003/2 on 192.168.123.100
Looking up port of RPC 100005/2 on 192.168.123.100
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 68k in
init started: BusyBox v0.60.2 (2002.06.30-14:29+0000) multi-call Bad inittab en
try: ::restart:/sbin/init
modprobe: modprobe: Can't locate module tmpfs
mount: Mounting none on /tmp failed: No such device
/etc/init.d/rcS: cannot create /etc/network/ifstate: No such file or directory
ifup: No such file or directory
Real Time Clock Driver v0.1
i2c-core.o: i2c core module
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
mID: 01
feID: dd
fpID: 5a
enxID: ffffffff
gtxID: 0b
hwREV: 05
fpREV: 81
DEMOD: VES1893
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 0).
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 1).
mice: PS/2 mouse device common for all mice
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
event0: Event device for input0
mouse0: PS/2 mouse device for input0
AVIA: $Id: avia_core.c,v 1.30 2002/05/06 02:18:18 obi Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.20 2002/06/07 14:00:23 tmbinc Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.14 2002/06/07 18:06:03 Jolt Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.89 2002/06/11 20:35:43 Jolt Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: RISC mem map size: 2048
avia_gt_gv: $Id: avia_gt_gv.c,v 1.20 2002/06/07 18:06:03 Jolt Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.14 2002/06/07 18:06:03 Jolt Exp $
write 1 event's ...
write 1 event's ...
avia_gt_capture: $Id: avia_gt_capture.c,v 1.20 2002/06/07 18:06:03 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.26 2002/06/07 18:06:03 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.18 2002/06/07 18:06:03 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
i2c-core.o: driver VES1893 DVB demodulator registered.
i2c-core.o: client [VES1893] registered to adapter [](pos. 4).
VES1893: attaching VES1893 at 0x10 avia_gt_core: masking unhandled irq reg 0 bit
6
to adapter
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.31 2002/05/30 00:39:03 obi Exp $
avia_gt_gv: set_input_mode (mode=3)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=3)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=3)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 90x36
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_oss: $Id: avia_gt_oss.c,v 1.6 2002/05/06 02:18:18 obi Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.89 2002/06/11 20:35:43 Jolt Exp $
avia_gt_napi: warning, misaligned queue 0 (is 32a00, size 10000), aligning...
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.14 2002/06/13 18:32:14 LazyT Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
Please press Enter to activate this console. [FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
$Id: sectionsd.cpp,v 1.126 2002/05/15 10:00:55 dirch Exp $
caching 504 hours
events are old 60min after their end time
dmxdev: set buffer size 40000 -> 60000
[camd] ca system id: 1702
$Id: zapit.cpp,v 1.190 2002/06/27 20:03:47 Homar Exp $
[getservices.cpp] /var/tuxbox/config/zapit/services.xml: No such file or directo
ry
[zapit] error parsing services!
[camd] no card is in slot #2
[camd] no card is in slot #1
Network LCD-Driver $Id: lcdd.cpp,v 1.49 2002/06/03 23:04:23 obi Exp $
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
dmxdev: set buffer size 40000 -> 60000
[FONT] FTC_Face_Requester (Micron/Regular)
Controld $Id: controld.cpp,v 1.58 2002/05/08 16:21:43 McClean Exp $
[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
dmxdev: set buffer size 40000 -> 60000
[nhttpd] Neutrino HTTP-Server starting..
dmxdev: set buffer size 40000 -> 60000
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.292 2002/06/24 23:20:50 dirch Exp $
[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance cdmxdev: set buffer size 40000 -> 60000
reated
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
fbcon_setup: No support for fontwidth 8
fbcon_setup: type 0 (aux 0, depth
not supportedavia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable streaming-control
[neutrino] Software update enabled
IP : 192.168.123.122
Netmask : 255.255.255.0
Broadcast: 192.168.123.255
Gateway : 192.168.123.254
[neutrino] menue setup
/.version: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
dmxdev: set buffer size 40000 -> 60000
[neutrino] timerd event register
dmxdev: set buffer size 40000 -> 60000
dmxdev: set buffer size 40000 -> 60000
dmxdev: set buffer size 40000 -> 60000
dmxdev: set buffer size 40000 -> 60000
dmxdev: set buffer size 40000 -> 60000
dmxdev: set buffer size 40000 -> 60000
.....
----------------------------------------------------------------------------
Hier ist also die GUI oben (aber keine Sender, kriseln)
DANKE !!! ZExMA
