kurz vorm Wochenende sehe ich eine neue cramfs Version vom 19.07.
Wollt ich gleich ausprobieren...
leider geht nix mehr.
Habe ne Sagem 1XI Kabel. Stecker raus und rein bringt kein Erfolg.
Hier mal mein Boot Log.
Hoffentlich hilfts was...
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID XX.XX.XX.XX
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0052
will verify ELF image, start= 0x800000, size= 202740
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Jul 12 2002 - 21:12:06)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Sagem
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 553421 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 553357 Bytes = 540 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19-rc2-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht,
wird bestraft ;-) #5 Fre Jul 19 17:18:29 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30908k available (1036k kernel code, 364k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:3b:2f:67
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
Using buffer write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.05.26-17:53+0000) multi-ca[i2c-8xx]: mpc
8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [](pos. 0).
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
AVIA: $Id: avia_core.c,v 1.30 2002/05/06 02:18:18 obi Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 3
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
write 1 event's ...
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
Lade alternativen avia_gt.o
/var/modules/avia_gt.o: kernel-module version mismatch
/var/modules/avia_gt.o was compiled for kernel version 2.4.19-rc1-dbox2
while this kernel is version 2.4.19-rc2-dbox2.
/lib/modules/2.4.19-rc2-dbox2/misc/dvb.o: unresolved symbol avia_gt_pcm_set_mpeg
_attenuation
/lib/modules/2.4.19-rc2-dbox2/misc/dvb.o: unresolved symbol avia_gt_pcm_set_pcm_
attenuation
Init AT76C651
/lib/modules/2.4.19-rc2-dbox2/misc/at76c651.o: unresolved symbol register_fronte
nd
/lib/modules/2.4.19-rc2-dbox2/misc/at76c651.o: unresolved symbol unregister_fron
tend
/lib/modules/2.4.19-rc2-dbox2/misc/at76c651.o:
Hint: You are trying to load a module without a GPL compatible license
and it has unresolved symbols. Contact the module supplier for
assistance, only they can help you.
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_set_queue
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_set_queue_irq
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol unregister_
demux
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_set_pcr_pid
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_set_queue_write_pointer
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_all
oc_irq
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol register_de
mux
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_force_discontinuity
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol gtx_set_que
ue_pointer
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_get
_info
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_dmx
_get_queue_write_pointer
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_napi.o: unresolved symbol avia_gt_fre
e_irq
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_vbi.o: unresolved symbol avia_gt_get_
info
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_sh
ow
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_ge
t_clut
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_input_size
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_pos
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_hi
de
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_get_i
nfo
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_size
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_input_mode
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_clut
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_se
t_blevel
/lib/modules/2.4.19-rc2-dbox2/misc/avia_gt_fb.o: unresolved symbol avia_gt_gv_ge
t_info
Network LCD-Driver $Id: lcdd.cpp,v 1.51 2002/07/10 16:29:08 LazyT Exp $
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
$Id: sectionsd.cpp,v 1.126 2002/05/15 10:00:55 dirch Exp $
caching 504 hours
events are old 60min after their end time
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[camd] /dev/dvb/card0/ca0: No such file or directory
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[sectionsd] DMX: DMX_STOP: Bad file descriptor
$Id: zapit.cpp,v 1.192 2002/07/17 03:04:32 obi Exp $
[getservices.cpp] going to parse cable Telekom
[zapit] reading Bouquets .........
[zapit] Found 10 bouquets.
[zapit] channels have been loaded succesfully
/dev/ost/frontend0: No such file or directory
[zapit] unable to open frontend devices. bye.
Segmentation fault
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
Controld $Id: controld.cpp,v 1.58 2002/05/08 16:21:43 McClean Exp $
[controld] Boxtype detected: (03, 3, 2, Sagem)
set event: 00000009
open: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
zapitclient: connect: No such file or directory
zapitclient: connect: No such file or directory
[sectionsd] DMX: /dev/ost/demux0: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.304 2002/07/13 01:10:37 dirch Exp $
[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
[neutrino] Error while setting framebuffer mode
The system is going down NOW !!
Sending SIGKILL to all processes.httpd] stop requested......
CXA2126 found
The system is halted. Press CTRL-ALT-DEL or turn off power
System halt
