>> zu Thread Sagem 1xI kein System

Anlaufschwierigkeiten? Was ist was? Worum geht's?
Wurzelxquadrat
Interessierter
Interessierter
Beiträge: 29
Registriert: Samstag 23. Februar 2002, 18:13

>> zu Thread Sagem 1xI kein System

Beitrag von Wurzelxquadrat »

Sooo......

Also wieso ich kein Logfile hatte ist geklärt.
Aus irgendeinem Grund ist mein Comport ausgestiegen.

Nach nem Neustart ging das Flashen auch wieder.

Das Logfile hab ich mal angehängt...sieht doch gar net so schlecht aus.

debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-c2.e0.d1.07.00.00-e2
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.2, My IP 192.168.0.100
debug: Sending TFTP-request for file D/LINUX@DBox2/Ppcboot.txt
will verify ELF image, start= 0x800000, size= 222280
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000


ppcboot 0.6.4 (Jul 12 2001 - 02:51:28)

Initializing...
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-3b-68-0e
FLASH: 8 MB
FB logo at: none
Input: serial
Output: serial

Any key druecken um das Flashing abzubrechen.. : 0
dbox2-ppcboot> bootp 100000 /D/LINUX@DBox2/13.img
BOOTP broadcast 1
TFTP from server 192.168.0.2; our IP address is 192.168.0.100
Filename '/D/LINUX@DBox2/13.img'.
Load address: 0x100000
Loading: #######################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################
done
lo: 0x100000
dbox2-ppcboot> protect off 10020000 107fffff
unprotecting 1
[0]-> [0] [Sb000b0] unprotecting 2
[0]-> [0] [Sb000b0] unprotecting 3
[0]-> [0] [Sb000b0] unprotecting 4
[0]-> [0] [Sb000b0] unprotecting 5
[0]-> [0] [Sb000b0] unprotecting 6
[0]-> [0] [Sb000b0] unprotecting 7
[0]-> [0] [Sb000b0] unprotecting 8
[0]-> [0] [Sb000b0] unprotecting 9
[0]-> [0] [Sb000b0] unprotecting a
[0]-> [0] [Sb000b0] unprotecting b
[0]-> [0] [Sb000b0] unprotecting c
[0]-> [0] [Sb000b0] unprotecting d
[0]-> [0] [Sb000b0] unprotecting e
[0]-> [0] [Sb000b0] unprotecting f
[0]-> [0] [Sb000b0] unprotecting 10
[0]-> [0] [Sb000b0] unprotecting 11
[0]-> [0] [Sb000b0] unprotecting 12
[0]-> [0] [Sb000b0] unprotecting 13
[0]-> [0] [Sb000b0] unprotecting 14
[0]-> [0] [Sb000b0] unprotecting 15
[0]-> [0] [Sb000b0] unprotecting 16
[0]-> [0] [Sb000b0] unprotecting 17
[0]-> [0] [Sb000b0] unprotecting 18
[0]-> [0] [Sb000b0] unprotecting 19
[0]-> [0] [Sb000b0] unprotecting 1a
[0]-> [0] [Sb000b0] unprotecting 1b
[0]-> [0] [Sb000b0] unprotecting 1c
[0]-> [0] [Sb000b0] unprotecting 1d
[0]-> [0] [Sb000b0] unprotecting 1e
[0]-> [0] [Sb000b0] unprotecting 1f
[0]-> [0] [Sb000b0] unprotecting 20
[0]-> [0] [Sb000b0] unprotecting 21
[0]-> [0] [Sb000b0] unprotecting 22
[0]-> [0] [Sb000b0] unprotecting 23
[0]-> [0] [Sb000b0] unprotecting 24
[0]-> [0] [Sb000b0] unprotecting 25
[0]-> [0] [Sb000b0] unprotecting 26
[0]-> [0] [Sb000b0] unprotecting 27
[0]-> [0] [Sb000b0] unprotecting 28
[0]-> [0] [Sb000b0] unprotecting 29
[0]-> [0] [Sb000b0] unprotecting 2a
[0]-> [0] [Sb000b0] unprotecting 2b
[0]-> [0] [Sb000b0] unprotecting 2c
[0]-> [0] [Sb000b0] unprotecting 2d
[0]-> [0] [Sb000b0] unprotecting 2e
[0]-> [0] [Sb000b0] unprotecting 2f
[0]-> [0] [Sb000b0] unprotecting 30
[0]-> [0] [Sb000b0] unprotecting 31
[0]-> [0] [Sb000b0] unprotecting 32
[0]-> [0] [Sb000b0] unprotecting 33
[0]-> [0] [Sb000b0] unprotecting 34
[0]-> [0] [Sb000b0] unprotecting 35
[0]-> [0] [Sb000b0] unprotecting 36
[0]-> [0] [Sb000b0] unprotecting 37
[0]-> [0] [Sb000b0] unprotecting 38
[0]-> [0] [Sb000b0] unprotecting 39
[0]-> [0] [Sb000b0] unprotecting 3a
[0]-> [0] [Sb000b0] unprotecting 3b
[0]-> [0] [Sb000b0] unprotecting 3c
[0]-> [0] [Sb000b0] unprotecting 3d
[0]-> [0] [Sb000b0] unprotecting 3e
[0]-> [0] [Sb000b0] unprotecting 3f
[0]-> [0] [Sb000b0] Un-Protected 63 sectors

dbox2-ppcboot> erase 10020000 107fffff
Erase Flash from 0x10020000 to 0x107fffff
sector 63 .... done
Erased 63 sectors

dbox2-ppcboot> cp.l 120000 10020000 1F8000
Copy to Flash... done

dbox2-ppcboot>
Sprüche lass ich die anderen machen.
Dietmar
Senior Member
Beiträge: 8282
Registriert: Mittwoch 10. Oktober 2001, 00:00

Beitrag von Dietmar »

Fein, das scheint zu passen.
Läuft es jetzt, oder wo hängts?
Wurzelxquadrat
Interessierter
Interessierter
Beiträge: 29
Registriert: Samstag 23. Februar 2002, 18:13

Beitrag von Wurzelxquadrat »

Nein ...komischerweise

Wenn ich im Neutrino-Menue was gewält habe bootet sie wieder von vorne.
Hab jetzt schon versch. Image probiert . Immer die selbe Leier.

Was kann ich noch machen ??

Wurzelx²
Sprüche lass ich die anderen machen.
Dietmar
Senior Member
Beiträge: 8282
Registriert: Mittwoch 10. Oktober 2001, 00:00

Beitrag von Dietmar »

Sind die Ucodes ok?
Schau mal unter Service -> Ucodes überprüfen.
Geht Enigma oder Lcars?
Wurzelxquadrat
Interessierter
Interessierter
Beiträge: 29
Registriert: Samstag 23. Februar 2002, 18:13

Beitrag von Wurzelxquadrat »

Wäre schön wenn ich so weit kommen würde, aber geht leider net.
Alles was ich machen kann ist im Bootmenü auszuwählen was ich starten will.
Danach beginnt die Box von neuem zu booten.

Wurzelx²
Sprüche lass ich die anderen machen.
Dietmar
Senior Member
Beiträge: 8282
Registriert: Mittwoch 10. Oktober 2001, 00:00

Beitrag von Dietmar »

Hast Du mal probiert maintaince zu starten? (Pin: 0000)
Wurzelxquadrat
Interessierter
Interessierter
Beiträge: 29
Registriert: Samstag 23. Februar 2002, 18:13

Beitrag von Wurzelxquadrat »

Ja ...hab ich jetzt eben mal getestet.
Nach der PIN-Eingabe bootet sie wieder neu.

ich werd noch wahnsinnig.

Weiß noch einer nen Rat ?

Wurzelx²
Sprüche lass ich die anderen machen.
Reichi
Erleuchteter
Erleuchteter
Beiträge: 477
Registriert: Sonntag 7. Oktober 2001, 00:00

Beitrag von Reichi »

Hallo!

Schalte bitte mal im Bootmanager alles außer Seriell aus, drücke auf start und Schalte die Box ein, den Log dann bitte posten.
Dann sehen wir ja wo's "hängt"

mfg,

Reichi
Wurzelxquadrat
Interessierter
Interessierter
Beiträge: 29
Registriert: Samstag 23. Februar 2002, 18:13

Beitrag von Wurzelxquadrat »

einfach nur die box starten oder beim flashen ???
Sprüche lass ich die anderen machen.
Dietmar
Senior Member
Beiträge: 8282
Registriert: Mittwoch 10. Oktober 2001, 00:00

Beitrag von Dietmar »

Einfach nur die Box starten. Dann sieht man was direkt beim Start abgeht.
Wurzelxquadrat
Interessierter
Interessierter
Beiträge: 29
Registriert: Samstag 23. Februar 2002, 18:13

Beitrag von Wurzelxquadrat »

da kommt im Com-Fenster gar nix
Sprüche lass ich die anderen machen.
Dietmar
Senior Member
Beiträge: 8282
Registriert: Mittwoch 10. Oktober 2001, 00:00

Beitrag von Dietmar »

Da muss was kommen (im com-terminal)
Die Verbindungsgeschwindigkeit im bootmanager steht auf 9600?
Es hängt ein Nullmodem dran?
Wurzelxquadrat
Interessierter
Interessierter
Beiträge: 29
Registriert: Samstag 23. Februar 2002, 18:13

Beitrag von Wurzelxquadrat »

Ach ja ...jetzt kommts

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0052

will verify ELF image, start= 0x800000, size= 202740
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Jul 12 2002 - 21:12:06)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Sagem
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 553421 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 553357 Bytes = 540 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19-rc2-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht,
wird bestraft ;-) #5 Fre Jul 19 17:18:29 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30908k available (1036k kernel code, 364k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:3b:68:0e
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
Using buffer write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.05.26-17:53+0000) multi-ca[i2c-8xx]: mpc
8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [](pos. 0).
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
AVIA: $Id: avia_core.c,v 1.30 2002/05/06 02:18:18 obi Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 3
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
write 1 event's ...
write 1 event's ...
CAM: attached to adapter
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
avia_gt_core: $Id: avia_gt_core.c,v 1.20 2002/06/07 14:00:23 tmbinc Exp $
avia_gt_core: autodetecting chip type... AViA eNX found
avia_gt_enx: $Id: avia_gt_enx.c,v 1.11 2002/06/07 17:53:45 Jolt Exp debug: DDF:
Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: WATCHDOG RESET
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-c2.e0.d1.07.00.00-e2
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0052

will verify ELF image, start= 0x800000, size= 202740
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Jul 12 2002 - 21:12:06)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Sagem
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 553421 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 553357 Bytes = 540 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19-rc2-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht,
wird bestraft ;-) #5 Fre Jul 19 17:18:29 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30908k available (1036k kernel code, 364k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:3b:68:0e
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
Using buffer write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.05.26-17:53+0000) multi-ca[i2c-8xx]: mpc
8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [](pos. 0).
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
AVIA: $Id: avia_core.c,v 1.30 2002/05/06 02:18:18 obi Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 3
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
write 1 event's ...
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
avia_gt_core: $Id: avia_gt_core.c,v 1.20 2002/06/07 14:00:23 tmbinc Exp $
avia_gt_core: autodetecting chip type... AViA eNX found
avia_gt_enx: $Id: avia_gt_enx.c,v 1.11 2002/06/07 17:53:45 Jolt Exp debug: DDF:
Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: WATCHDOG RESET
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-c2.e0.d1.07.00.00-e2
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0052

will verify ELF image, start= 0x800000, size= 202740
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Jul 12 2002 - 21:12:06)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Sagem
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
LCD: ready
FB: loading - ready
In: serial
Sprüche lass ich die anderen machen.
Dietmar
Senior Member
Beiträge: 8282
Registriert: Mittwoch 10. Oktober 2001, 00:00

Beitrag von Dietmar »

Hm, poste mal die genaue Dateigröße Deiner Ucodes.
Evtl. hat die avia600.ux nen Schaden.
Ansonsten könnt man fast auf den avia-chip tippen.
Wurzelxquadrat
Interessierter
Interessierter
Beiträge: 29
Registriert: Samstag 23. Februar 2002, 18:13

Beitrag von Wurzelxquadrat »

126846 Byte .....

Aber ich hab auch schon andere Images probiert ( die fliegenden Teile ) da muss doch das booten auch ohne Ucodes gehen oder sehe ich das falsch .
Sollte es dennoch der Avia Chip sein ...ist das reperabel ??? und was kostet so was .

Wurzel
Sprüche lass ich die anderen machen.
Reichi
Erleuchteter
Erleuchteter
Beiträge: 477
Registriert: Sonntag 7. Oktober 2001, 00:00

Beitrag von Reichi »

also theoretisch wäre da Avia reparabel aber:

1. Treib nen Avia auf (ok das geht noch relativ leicht indem du ne defekt Box mit gehendem Avia auftreibst)
und

2. finde jemanden der dir das Ding aus- und wieder einlötet
Dietmar
Senior Member
Beiträge: 8282
Registriert: Mittwoch 10. Oktober 2001, 00:00

Beitrag von Dietmar »

Ist das die Größe der avia600.ux?
Aus welcher BN-Version stammt die?
Wenn 2.01: Die sollte eigtl. 128.214 Bytes sein.
Versuch mal eins von den McClean-Images, die starten auch ohne Ucodes.
Wenn es damit auch nicht will: http://www.dvbtotal.de
Wurzelxquadrat
Interessierter
Interessierter
Beiträge: 29
Registriert: Samstag 23. Februar 2002, 18:13

Beitrag von Wurzelxquadrat »

Man oh Man
Ein Chat ist ja direkt träge dagegen :-)


ist der defekte chip jetzt eine Vermutung oder eher eine zusage aus der Ferne .
Ich kenn mich da überhaupt net aus .
Sprüche lass ich die anderen machen.
Dietmar
Senior Member
Beiträge: 8282
Registriert: Mittwoch 10. Oktober 2001, 00:00

Beitrag von Dietmar »

Ferndiagnosen sind immer ne Vermutung. :)
Reichi
Erleuchteter
Erleuchteter
Beiträge: 477
Registriert: Sonntag 7. Oktober 2001, 00:00

Beitrag von Reichi »

Der Chip ist ne Vermutung:

Aus welcher BN Version ist denn deine Avia600ux???
Weil wenn die wirklich aus BN 2.01 ist, dann ist die hinüber...
und dann liegts nur an der!

mfg

Reichi
SoLaLa
Tuxboxer
Tuxboxer
Beiträge: 6119
Registriert: Mittwoch 3. April 2002, 00:32

Beitrag von SoLaLa »

126846 byte ist normalerweise ok, das ist vb017
aber vielleicht wäre die vb022 angebracht, zumindest zum ausprobieren
never change a running system