Ich habe mir auf anraten eines Arbeitskollegen die Linux-Software auf meine Box gespielt, und nach einigen vielen Problemen es auch hinbekommen das sie aufgespielt ist.
Leider habe ich in dem moment wo ich endlich die box soweit hatte das ich die software aufspiele konnte vergessen die sicherung zu machen.
Die ucodes und avia- dateien habe ich ja von ihm bekommen, aber leider hat er eine sat und ich eine Kabel- Box. wo kann ich eine passende cam - version herbekommen?
2. die box fährt hoch, macht aber garkein Bild auf dem ernseher, web-interface geht, liegt das am falschen cam?
ne frage ist das ernst zu nehmen?
"Warning: CPU Core has Silicon Bugs -- Check the Errata"
hier mein log des boots:
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044
will verify ELF image, start= 0x800000, size= 202740
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Jul 13 2002 - 20:02:35)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 553421 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 553357 Bytes = 540 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19-rc2-dbox2 (von alexW) Wer Kernels nachmacht, oder faelscht,
wird bestraft ;-) #5 Fre Jul 19 17:18:29 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30908k available (1036k kernel code, 364k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:17:08:0d
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.05.26-17:53+0000) multi-ca[i2c-8xx]: mpc
8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
event: init ...
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
AVIA: $Id: avia_core.c,v 1.30 2002/05/06 02:18:18 obi Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
write 1 event's ...
write 1 event's ...
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
avia_gt_core: $Id: avia_gt_core.c,v 1.20 2002/06/07 14:00:23 tmbinc Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.14 2002/06/07 18:06:03 Jolt Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.91 2002/07/08 15:12:47 wjoost Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: RISC mem map size: 2048
avia_gt_gv: $Id: avia_gt_gv.c,v 1.21 2002/07/21 15:16:22 waldi Exp $
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.14 2002/06/07 18:06:03 Jolt Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.20 2002/06/07 18:06:03 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.26 2002/06/07 18:06:03 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.18 2002/06/07 18:06:03 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Init VES1820
i2c-core.o: driver VES1820 DVB demodulator registered.
attach_adapter
VES1820: attaching VES1820 at 0x10
i2c-core.o: client [VES1820] registered to adapter [](pos. 4).
VES1820: attached to adapter
$Id: ves1820.c,v 1.28 2002/07/05 12:39:30 Homar Exp $
INIT: Einsprung
avia_gt_napi: $Id: avia_gt_napi.c,v 1.88 2002/05/07 16:59:19 Jolt Exp $
avia_gt_napi: warning, misaligned queue 0 (is 32a00, size 10000), aligning...
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.15 2002/07/02 09:31:22 LazyT Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.33 2002/07/19 22:59:21 waldi Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 90x36
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
CXA2092 found
CXA2092 found
Network LCD-Driver $Id: lcdd.cpp,v 1.51 2002/07/10 16:29:08 LazyT Exp $
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
$Id: sectionsd.cpp,v 1.126 2002/05/15 10:00:55 dirch Exp $
caching 504 hours
events are old 60min after their end time
[camd] Unknown 1.CMD-Class 03
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] ca system id: 1722
[camd] card_country: TEL
[camd] card_number: 9002155234
[camd] card_version: 0384
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] no card is in slot #2
[camd] a card is in slot #1
[camd] no card is in slot #2
[camd] a card is in slot #1
$Id: zapit.cpp,v 1.193 2002/07/22 01:57:19 Homar Exp $
[getservices.cpp] /var/tuxbox/config/zapit/services.xml: No such file or directo
ry
[zapit] error parsing services!
Controld $Id: controld.cpp,v 1.58 2002/05/08 16:21:43 McClean Exp $
[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[camd] no card is in slot #2
[camd] a card is in slot #1
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.307 2002/07/22 21:08:07 wjoost Exp $
[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
IP : 192.168.0.23
Netmask : 255.255.255.0
Broadcast: 192.168.0.255
Gateway :
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[neutrino] timerd event register
und der balken bei neutrino bleibt kurz vor dem ende des displays stehen.
