Mal wieder Kanalsuche Kabel

Anlaufschwierigkeiten? Was ist was? Worum geht's?
Kanalsuche
Interessierter
Interessierter
Beiträge: 21
Registriert: Dienstag 21. Januar 2003, 04:30

Mal wieder Kanalsuche Kabel

Beitrag von Kanalsuche »

Hallo,
habe eine D-Box2 Kabel von Nokia.
Nach neuer Linux Installation habe ich nur noch die Kanalsuche für SAT!
Nach mehrmaligen booten hatte ich denn die Kanalsuche für Kabel aber der hat nur Mediavision Kanäle gefunden, die auch einwandfrei funktionierten. Habe mir dann Sendersettings eingespielt nur seit dem habe ich wieder die SAT kanalsuche und keine Sender mehr! Weiss einfach nicht weiter und hoffe auf hilfe. Hier noch mein LOG File:


debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: unknown demodulatordebug: BMon V1.0 mID 01
debug: feID 00 gtxID 0b
debug: fpID 5a dsID 01-ff.8c.1f.07.00.00-59
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0044

will verify ELF image, start= 0x800000, size= 202996
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Aug 5 2002 - 09:06:03)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Watchdog enabled
Board: DBOX2, Nokia
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . done.
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 634725 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 634661 Bytes = 619 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft ;-) #1 Die Dez 31 18:36:38 CET 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 252000000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30816k available (1120k kernel code, 372k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:1a:20:76
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Amd/Fujitsu Extended Query Table v1.1 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu
les/2.4.20/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.20/misc/event.o
event: init ...
Using /lib/modules/2.4.20/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2092] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20/misc/dvb_demux.o
Using /lib/modules/2.4.20/misc/dvbdev.o
Using /lib/modules/2.4.20/misc/avia.o
AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $
Using /lib/modules/2.4.20/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 1
Using /lib/modules/2.4.20/misc/cam.o
der moment ist gekommen...
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).
CAM: attached to adapter
write 1 event's ...
write 1 event's ...
Using /lib/modules/2.4.20/misc/dmxdev.o
Using /lib/modules/2.4.20/misc/dvb_frontend.o
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
Using /lib/modules/2.4.20/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.22 2002/09/13 22:53:55 Jolt Exp $
avia_gt_core: autodetecting chip type... AViA GTX found
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.17 2002/09/15 18:06:26 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.6 2002/09/19 21:09:20 Jolt Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.134 2002/09/21 00:00:08 Jolt Exp $
avia_gt_dmx: Successfully loaded ucode VB1.7
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.18 2002/09/25 18:50:52 Jolt Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.20/misc/dvb.o
Init VES1893
Using /lib/modules/2.4.20/misc/ves1893.o
i2c-core.o: driver VES1893 DVB demodulator registered.
Using /lib/modules/2.4.20/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.130 2002/09/18 15:57:24 Jolt Exp $
avia_gt_napi: hardware section filtering disabled.
Using /lib/modules/2.4.20/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.16 2002/08/22 13:39:33 Jolt Exp $
avia_gt_vbi: got demux C-Cube - AViA eNX/GTX
Using /lib/modules/2.4.20/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.36 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.20/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.11 2002/09/25 18:50:52 Jolt Exp $
Using /lib/modules/2.4.20/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.4 2002/08/22 13:39:33 Jolt Exp $
CXA2092 found
CXA2092 found
cdkVcInfo $Id: cdkVcInfo.c,v 1.1 2002/12/19 16:10:45 alexW Exp $

$Id: sectionsd.cpp,v 1.148 2002/12/09 20:07:52 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
[camd] no card is in slot #2
[camd] no card is in slot #1
[camd] ca system id: 1722
$Id: zapit.cpp,v 1.286 2003/01/03 12:41:31 alexw Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conffor reading.

dvb.c: no frontend available
[frontend.cpp:CFrontend:62] /dev/dvb/card0/frontend0: No such device or address
[zapit] unable to open frontend devices. bye.
Controld $Id: controld.cpp,v 1.88 2003/01/07 19:08:27 Zwen Exp $

[controld] Boxtype detected: (01, 1, 1, Nokia)
set event: 00000009
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.389 2003/01/12 16:41:17 Zwen Exp $

[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
IP : 192.168.5.25
Netmask : 255.255.255.0
Broadcast: 192.168.5.255
Gateway :
[neutrino] menue setup
[CHTTPUpdater] HTTP-Basepath: http://dboxupdate.berlios.de/images/
[CHTTPUpdater] Image-Filename: cdk.cramfs
[CHTTPUpdater] Version-Filename: cdk.cramfs.version
loading locales: scandir: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[neutrino] timerd event register
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
Gunspillage
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Dienstag 21. Januar 2003, 20:43

Beitrag von Gunspillage »

Hi,

ich hab genau das gleiche Problem, auch das Bootlog sieht meinem sehr ähnlich.
Allerdings hab ich das ganze auf ner Sagem-Box...
Tom1069
Erleuchteter
Erleuchteter
Beiträge: 664
Registriert: Donnerstag 4. Juli 2002, 00:53

Beitrag von Tom1069 »

Taucht das hier bei dir auch oben im Log auf?

debug: unknown demodulatordebug: BMon V1.0 mID 01

Was hattest du denn vorher mit der Box gemacht?
Gunspillage
Neugieriger
Neugieriger
Beiträge: 9
Registriert: Dienstag 21. Januar 2003, 20:43

Beitrag von Gunspillage »

Nein, es taucht nicht auf.
Mein Log beginnt folgendermaßen:

debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.1 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-dd.b4.85.07.00.00-c1
debug: HWrev 41 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08

Vorher? Ich hab den Debug-Modus aktiviert und den Schreibschutz aufgehoben, so wie in den gängigen Anleitungen beschrieben.

Kann es sein, dass ich dabei mit den 9V, die ich an die Flash-Bausteine führen musste, vielleicht irgendeinen Chip der DBox zerstört habe?

Was ist

Init VES1993
Using /lib/modules/2.4.20/misc/ves1993.o
i2c-core.o: driver VES1993 DVB DECODER registered.
ves1993: not found.
i2c-core.o: driver unregistered: VES1993 DVB DECODER
insmod: init_module: ves1993: Device or resource busy

Das klingt nicht sonderlich gut, oder?
Kanalsuche
Interessierter
Interessierter
Beiträge: 21
Registriert: Dienstag 21. Januar 2003, 04:30

Beitrag von Kanalsuche »

Ich habs raus bei mir.
Ist ein Wärmefehler. Mein Tuner ist defekt. Wenn ich das Gerät neu anschalte habe ich die Kabel Kanalsuche. Nach etwa 5 Minuten ist schluss.