Kann keine FTP Verbindung mit Windows Commander zur DBox herstellen .
Habe schon das ganze Board nach dem Problem durchforstet und alle möglichen Fehlerquellen
überprüft.
Im Bootmanager kommt unten rechts "Pinging DBoxII...failed!"
Irgendwie hab ich es doch geschafft das Orginalimage auszulesen und die Box
bis zur Einspielung der cdk.cramfs und ucodes zu bringen. Jetzt bekomme
ich aber keine FTP Verbindung mit Windows Commander hin.
Kein Ping zur Box mit BM/Eingabeaufforderung/FTP Programm/Telnet/Hyperterminal nichts funktioniert !
Firewall ist abgeschalten.
Nullmodemkabel ist überprüft (nutze es für meinen Humax zum einspielen von Sendelisten - OK!)
Habe eine 3COM 3C900B COMBO mit aktuellen Treibern (auch schon verschiedene ausprobiert)
Habe verschiedene Einstellungen getestet (10MB Halfduplex/Auto)
Mediasensing ist ausgeschaltet !
Habe Windows 2000 und Windows 98SE auf dem Rechner und bei beiden Systemen kein Ping !
Die grüne Lampe leuchtet auf der Netzwerkkarte.
Crossover Kabel ist durchgeprüft und OK !(steht auch drauf - Crossover Patchkabel)
Meine Rechner IP 192.168.1.30
Subnetzmaske 255.255.255.0
DBox IP 192.168.1.31
Bei FTP : 192.168.1.31
User: root
Passw: dbox2
Habe die Box nach MHC Methode von Dietmar Hölscher
in den Debug gebracht und die "wirren Zeichen" waren nach dem Neustart der Box im Display.
Kann sein das die Netzwerkkarte einen Defekt hat ?
Kann man das prüfen ?
Wenn ich das Crossover Kabel in die BJ45 Buchse Stecke und die Kontakte durchprüfe habe ich Verbindung zu
mehreren Kontakten !
Stecker Kontakt zu Buchse
Pin1 Pin1/2/4/5
Pin2 Pin1/2/4/5
Pin3 Pin7/8
Pin4 Pin1/2/4/5
Pin5 Pin1/2/4/5
Pin6 Pin7/8
Pin7 Pin3/6
Pin8 Pin3/6
Kann das jemand bestätigen ?
Hier mal das Log aus dem Bootmanager :
:debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.0 mID 02
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-1f.e6.39.08.00.00-fa
debug: HWrev 01 FPrev 0.30
debug: B/Ex/Fl(MB) 32/00/08
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/philips-dbox2/kernel/os in Flash-FS
debug: Got Block #0052
will verify ELF image, start= 0x800000, size= 203620
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Feb 17 2003 - 19:30:34)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Phillips
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .

LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 577057 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 576993 Bytes = 563 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Nach erneutem Start und drücken der Option 2 :
:debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.0 mID 02
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-1f.e6.39.08.00.00-fa
debug: HWrev 01 FPrev 0.30
debug: B/Ex/Fl(MB) 32/00/08
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/philips-dbox2/kernel/os in Flash-FS
debug: Got Block #0052
will verify ELF image, start= 0x800000, size= 203620
verify sig: 262
Branching to 0x40000
PPCBoot 1.1.6 (TuxBox) (Feb 17 2003 - 19:30:34)
CPU: PPC823ZTnnB2 at 65.900 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Phillips
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .

LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 577057 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 576993 Bytes = 563 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft ;-) #1 Son Sep 22 10:35:10 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247125000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.53 BogoMIPS
Memory: 30944k available (1008k kernel code, 356k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:2d:07:56
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.09.22-10:05+0000) multi-caUsing /lib/modu
les/2.4.19/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.19/misc/info.o
Using /lib/modules/2.4.19/misc/event.o
event: init ...
Using /lib/modules/2.4.19/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 0
).
Using /lib/modules/2.4.19/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 2
[lcdip] Bootmanager IP gefunden.
In oberem Teil steht :
***Adapter Desc: 3Com EtherLink PCI
***MAC address: 00:04:76:21:04:8C Local IP: 192.168.1.30 (via Packet-Driver #2)
***BootP server started... Port 67
***TFTP server started... Port 69
BootP> Answer sent!
Ist wenigstens mein Debug OK ? (hatte die bekannten"wirren Zeichen" im Display)
Habe ich vom Anfang beim Debug eine Fehler gemacht das ich keinen Ping bekomme ?
Ist das ausgelesene Orginal Image auch jetzt Schrott ?
Dieses Image habe ich erst auslesen können als ich im Bootmanager das Häkchen bei IP-Debug Messages gesetzt habe .
War das ein Fehler ?
Kann ich das Orginal Image jetzt noch gebrauchen ?
Habe eine Flash.img mit 7,87 MB ausgelesen und eine Boot.img mit 128 KB
Die 5 Dateien sind auch da !
avia600.ux 125 KB
avia500.ux 98,9 KB
ucode 2 KB
os 1,2 MB
cam-alpha 128 kb
Habe mich eigendlich streng nach den Anleitungen gehalten deshalb kann es wahrscheinlich nur die Netzwerkkarte sein (gebraucht bei eBay)
Nach dem Debug (wirre Zeichen im Display) habe ich die Box nochmal an den Fernseher gehangen und die Betanova 2.01 lief noch Super !
Erst dann habe ich angefangen mit auslesen und einspielen.
Werde mal eine andere Karte probieren !
Hoffendlich bestätigt mir jemand, das bis hierhin (Einspielen von cdk.cramfs und ucodes alles ok ist (Box jetzt Schrott ?)
MfG
whriteme