meine Box bootet seit einigen Tagen nicht mehr:
PPCBoot 1.1.6 (TuxBox) (Jul 12 2002 - 20:57:43)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Sagem
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.find_inode failed for name=tuxbox
load: Failed to find inode
LCD: find_inode failed for name=tuxbox
load: Failed to find inode
ready - can't find logo in flash - try network
BOOTP broadcast 1
mir der Hilfe von "DieMade" konnte ich die Ucodes aus dem Img. der Box auslesen.
Versuche nun per BootManager und Yadd die Box übers Netz zu booten (Ucodes sind in das UcodeVerzeichnis im Yadd kopiert).
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Das Fernseherbild meint: Ucodes nicht vorhanden
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Ausgabe des oberen Fensters im BootManager:
***Adapter Desc: 3Com EtherLink PCI (via IpHlpApi #0)
***MAC address: 00:04:76:0B:C3:7A Local IP: 192.168.75.1
***BootP server started... Port 67
***TFTP server started... Port 69
BootP> Request from 00:50:9C:30:6E:40 (assuming that this is DBox).
BootP> Created dynamic ARP entry for DBoxIP 192.168.75.23 with MAC 00:50:9C:30:6E:40
BootP> Answer sent!
TFTP> Started TFTP-Transfer for "M:\dbox2\tftpboot\ppcboot"...
TFTP> Transfer finished, sent 399 blocks
BootP> Created dynamic ARP entry for DBoxIP 192.168.75.23 with MAC 00:50:9C:30:6E:40
BootP> Answer sent!
TFTP> Non-BootP TFTP-transfer requested "M\dbox2\tftpboot\logo-lcd"
TFTP> Started TFTP-Transfer for "M:\dbox2\tftpboot\logo-lcd"...
TFTP> Transfer finished, sent 16 blocks
BootP> Created dynamic ARP entry for DBoxIP 192.168.75.23 with MAC 00:50:9C:30:6E:40
BootP> Answer sent!
TFTP> Non-BootP TFTP-transfer requested "M\dbox2\tftpboot\logo-fb"
TFTP> Started TFTP-Transfer for "M:\dbox2\tftpboot\logo-fb"...
TFTP> Transfer finished, sent 139 blocks
BootP> Created dynamic ARP entry for DBoxIP 192.168.75.23 with MAC 00:50:9C:30:6E:40
BootP> Answer sent!
TFTP> Non-BootP TFTP-transfer requested "M\dbox2\tftpboot\kernel-yadd"
TFTP> Started TFTP-Transfer for "M:\dbox2\tftpboot\kernel-yadd"...
TFTP> Transfer finished, sent 1153 blocks
BootP> Created dynamic ARP entry for DBoxIP 192.168.75.23 with MAC 00:50:9C:30:6E:40
BootP> Answer sent!
1 - mountd: mount: path: M/dbox2/yaddroot/
0 - nfsd: getattr: cannot send reply
0 - nfsd: getattr: cannot send reply
0 - nfsd: NFS_READ: cannot send reply
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Hier die DboxShell:
LCD driver (KS0713) initialized
BOOTP broadcast 1
TFTP from server 192.168.75.1; our IP address is 192.168.75.23
Filename 'M/dbox2/tftpboot/logo-lcd'.
Load address: 0x130000
Loading: ##
LCD logo at: 0x130000 (0x1FD2814 bytes)
BOOTP broadcast 1
TFTP from server 192.168.75.1; our IP address is 192.168.75.23
Filename 'M/dbox2/tftpboot/logo-fb'.
Load address: 0x120000
Loading: ##############
FB logo at: 0x0 (0x1FC0000 bytes)
AVIA Frambuffer
Input: serial
Output: serial
1: Console on ttyS0
2: Console on null
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
BOOTP broadcast 1
TFTP from server 192.168.75.1; our IP address is 192.168.75.23
Filename 'M/dbox2/tftpboot/kernel-yadd'.
Load address: 0x100000
Loading: #######################################################################
#############################################
## Booting Linux kernel at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 590089 Bytes = 576 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.19 (von alexW) Wer Kernels nachmacht, oder faelscht, wird best
raft ;-) #1 Mon Sep 23 08:56:15 CEST 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 ip=bootp root=/dev/nfs rw nfsroot=192.168.75.
1:M/dbox2/yaddroot/
WARNING: Frequency is not in HZ. Please consider using a newer bootloader!
WARNING: OLD intfreq = 66 busfreq = 66
WARNING: NEW intfreq = 66000000 busfreq = 66000000
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.53 BogoMIPS
Memory: 30944k available (1036k kernel code, 320k data, 68k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:30:6e:40
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Using word write method
Creating 3 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Sending BOOTP requests . OK
IP-Config: Got BOOTP answer from 192.168.75.1, my address is 192.168.75.23
IP-Config: Guessing netmask 255.255.255.0
IP-Config: Complete:
device=eth0, addr=192.168.75.23, mask=255.255.255.0, gw=255.255.255.255,
host=192.168.75.23, domain=, nis-domain=(none),
bootserver=192.168.75.1, rootserver=192.168.75.1, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 192.168.75.1
Looking up port of RPC 100005/1 on 192.168.75.1
VFS: Mounted root (nfs filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 68k init
init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu
les/2.4.19/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.19/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.19/misc/event.o
event: init ...
Using /lib/modules/2.4.19/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [](pos. 0).
Using /lib/modules/2.4.19/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.19/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.19/misc/dvb_demux.o
Using /lib/modules/2.4.19/misc/dvbdev.o
Using /lib/modules/2.4.19/misc/avia.o
AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $
Using /lib/modules/2.4.19/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 3
Using /lib/modules/2.4.19/misc/cam.o
insmod: init_module: cam: Input/output error
write 1 event's ...
write 1 event's ...
Using /lib/modules/2.4.19/misc/dmxdev.o
Using /lib/modules/2.4.19/misc/dvb_frontend.o
[FONT] initializing core...
[FONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Bold)
Using /lib/modules/2.4.19/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.22 2002/09/13 22:53:55 Jolt Exp $
avia_gt_core: autodetecting chip type... AViA eNX found
avia_gt_enx: $Id: avia_gt_enx.c,v 1.13 2002/09/02 19:25:37 Jolt Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.6 2002/09/19 21:09:20 Jolt Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.134 2002/09/21 00:00:08 Jolt Exp $
avia_gt_dmx: Successfully loaded ucode V0.14
ENX-INITed -> 0
there MIGHT be no TS
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.18 2002/09/25 18:50:52 Jolt Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.19/misc/dvb.o
insmod: unresolved symbol cam_read_message
insmod: unresolved symbol cam_reset
insmod: unresolved symbol cam_write_message
Init VES1993
Using /lib/modules/2.4.19/misc/ves1993.o
insmod: unresolved symbol register_frontend
insmod: unresolved symbol unregister_frontend
Using /lib/modules/2.4.19/misc/avia_gt_napi.o
insmod: unresolved symbol unregister_demux
insmod: unresolved symbol register_demux
Using /lib/modules/2.4.19/misc/avia_gt_vbi.o
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.16 2002/08/22 13:39:33 Jolt Exp $
avia_gt_vbi: error - no demux found
insmod: init_module: avia_gt_vbi: Input/output error
Using /lib/modules/2.4.19/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.36 2002/08/22 13:39:33 Jolt Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.19/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.11 2002/09/25 18:50:52 Jolt Exp $
cdkVcInfo $Id: cdkVcInfo.c,v 1.0 2002/09/26 20:48:26 alexW Exp $
Network LCD-Driver $Id: lcdd.cpp,v 1.54 2002/08/31 22:30:27 obi Exp $
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
/var/tuxbox/config/lcdd.conf: No such file or directory
[FONT] initializing core...
[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
[sectionsdclient] connect: No such file or directory
$Id: sectionsd.cpp,v 1.135 2002/10/04 16:31:25 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[camd] /dev/dvb/card0/ca0: No such file or directory
[sectionsd] DMX: DMX_STOP: Bad file descriptor
$Id: zapit.cpp,v 1.253 2002/10/04 18:25:17 thegoodguy Exp $
/var/tuxbox/config/zapit/services.xml: No such file or directory
[zapit] error parsing services!
/dev/dvb/card0/frontend0: No such file or directory
[zapit] unable to open frontend devices. bye.
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
Segmentation fault
Controld $Id: controld.cpp,v 1.64 2002/10/05 20:46:20 dirch Exp $
[controld] error while loading settings: /var/tuxbox/config/controld.conf
[controld] using defaults
[controld] Boxtype detected: (03, 3, 2, Sagem)
set event: 00000009
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.335 2002/10/05 20:46:20 dirch Exp $
[neutrino] frameBuffer Instance created
[neutrino] vcrControl Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
/var/tuxbox/config/neutrino.conf: No such file or directory
/var/tuxbox/config/scan.conf: No such file or directory
[neutrino] error while loading scan-settings, using defaults!
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[neutrino] menue setup
scandir: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[neutrino] control event register
[neutrino] sectionsd event register
[neutrino] zapit event register
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[neutrino] timerd event register
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Was mache ich falsch ???