@Gagga,
hab den Snapshot vom 19.11.03 auf meine Test-Box (Philips Sat 2xi) geschoben.
Hier die Ausgaben mittels Minicom, from booten bis zur Nutzung mit dem neuen Moviplayer.
Das Resyncing wird auch brav gemacht, das sieht man auch weiter unten im Log.
Also, der selbstgestreamte Film (ggrab, Sender N24) läuft wie gehabt zu Beginn asyncron, mittels grüner Taste wird die Syncronität wieder hergestellt.
Die Syncronität hält etwa 15 Sekunden an, danach wieder grüne Taste und wieder Erfolgserlebnis.
Dabei sieht es so aus als würde das Bild schneller vorlaufen um den Ton wieder ein zu holen.
Manchmal (ca 30-40%) erscheint dabei die Meldung "Puffern", wobei er sich hierbei wohl dann auch mal verschluckt und anscheinend den Einstieg nicht sofort wieder findet.
Das "Puffern" dauert dann ein paar Sekunden (ca 5-10 Sek) und dann geht's aber auch weiter.
Mal so ne Überlegung, der Prozeß der beim Drücken der Grünen Taste gestartet wird, wenn dieser nicht so CPU-lastig wäre, könnte dieser doch automatisch (nicht schlagen) alle 10 Millisekunden laufen, um für das menschliche Auge ein sauberes Ergebnis zu liefern.
So braucht man net ständig die grüne Taste drücken.
Ich vermut mal, die grüne Taste ist eh net der Endzustand, eher als Testmodus zum Feedback bekommen, oder?
Übrigens mein VLC ist Version 0.6.2 auf Eisfair/Linux mit nem P100,32 Mb Ram, 120 GB Festplatte,CPU Last während dieses Testes ca 35 %.
Gruß Frockert
Anbei das Minicom-Log
{debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.0 mID 02
debug: feID 00 enxID 03
debug: fpID 52 dsID
debug: HWrev 01 FPrev 0.30
debug: B/Ex/Fl(MB) 32/00/08
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/philips-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 146964
verify sig: 262
Branching to 0x40000
U-Boot 0.4.0 (TuxBox) (Oct 16 2003 - 18:02:34)
CPU: PPC823ZTnnB2 at 65.900 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Philips, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load complete: 590500 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 590436 Bytes = 576.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.22-dbox2 (von alexW) (gcc version 3.2.3) #1 So Nov 2 19:55:353
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247125000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Warning: real time clock seems stuck!
Console: colour dummy device 80x25
Calibrating delay loop... 65.53 BogoMIPS
Memory: 30936k available (1008k kernel code, 364k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (
rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communication.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:2d:22:55
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/coUsing /lib/modules/2.4.22-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.22-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.22-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.22-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter PowerPC 8xx I2C adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.22-dbox2/misc/dbox2_fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [PowerPC.
Using /lib/modules/2.4.22-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.22-dbox2/misc/avs.o
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [STV6412] registered to adapter [PowerPC 8xx I2C adapter](po.
Using /lib/modules/2.4.22-dbox2/misc/saa7126.o
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](po.
Using /lib/modules/2.4.22-dbox2/misc/cam.o
$Id: cam.c,v 1.28 2003/10/16 08:44:10 alexw Exp $
i2c-core.o: driver DBox2-CAM registered.
CAM: attaching CAM at 0x6e
i2c-core.o: client [DBOX2-CAM] registered to adapter [PowerPC 8xx I2C adapter](.
CAM: attached to adapter PowerPC 8xx I2C adapter
Using /lib/modules/2.4.22-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.22-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.17 2003/11/14 21:20:27 carjay Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
i2c-core.o: client [dvb] registered to adapter [PowerPC 8xx I2C adapter](pos. 4.
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.22-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.22-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.22-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.79 2003/10/16 08:42:20 alexw Exp $
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.11 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.22-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.43 2003/10/08 19:54:24 obi Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.194 2003/11/17 08:22:21 diemade Exp $
avia_gt_dmx: loaded ucode vB107
avia_gt_dmx: hw section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.37 2003/09/30 05:45:35 obi Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.28 2003/09/30 05:45:35 obi Exp $
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.22-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.52 2003/11/06 14:25:59 tklamm Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.22-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
cdkVcInfo $Id: cdkVcInfo.c,v 1.4 2003/11/03 09:15:39 alexw Exp $
Using /lib/modules/2.4.22-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.22-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.23 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.22-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.22-dbox2/misc/tda8044h.o
DVB: registering frontend 0:0 (TDA8044H QPSK Demodulator)...
Using /lib/modules/2.4.22-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.25 2003/09/12 03:01:51 obi Exp $
Using /lib/modules/2.4.22-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.188 2003/09/30 05:45:35 obi Exp $
$Id: sectionsd.cpp,v 1.167 2003/06/18 12:19:23 alexw Exp $
caching 504 hours
events are old 60min after their end time
$Id: zapit.cpp,v 1.332 2003/10/14 12:48:59 thegoodguy Exp $
/var/tuxbox/config/zapit/services.xml: No such file or directory
[camd] ca system id: 1702
$Id: controld.cpp,v 1.110 2003/10/21 22:48:25 zwen Exp $
[controld] Boxtype detected: (2, Philips D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[cdkVcInfo] Version (Image): 1107200311191238
[neutrino] frameBuffer Instance created
1024k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
[camd] no card is in slot #2
[camd] no card is in slot #1
Using /lib/modules/2.4.22-dbox2/kernel/net/sunrpc/sunrpc.o
Using /lib/modules/2.4.22-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.22-dbox2/kernel/fs/nfs/nfs.o
Mount(0) 192.168.0.7:/daten/daten/band3/mp3 -> /mnt/mp3
[neutrino] menue setup
loading locales: scandir: No such file or directory
[neutrino] registering as event client
[neutrino] initialized everything
[ConfigFile] Unable to open file /var/tuxbox/config/bookmarks for reading.
actionKey=fileplayback
[movieplayer.cpp] Startdir: vlc:///daten
readDir_vlc vlc:///daten/
[FileBrowser] vlc URL:
http://192.168.0.7:8080/admin/dboxfiles ... r=%2FdateF
readDir_vlc vlc:///daten/dbox/
[FileBrowser] vlc URL:
http://192.168.0.7:8080/admin/dboxfiles ... r=%2FdateF
[movieplayer.cpp] Generated FILE MRL: %2Fdaten%2Fdbox%2FN24%5F24%5FStunden%5F%5g
[movieplayer.cpp] ringbuffer created
[movieplayer.cpp] mrl:%2Fdaten%2Fdbox%2FN24%5F24%5FStunden%5F%5F%5FDie%5FN24%5Fg
[movieplayer.cpp] ReceiveStreamThread started
[movieplayer.cpp] read starting
[movieplayer.cpp] HTTP Result (emptyurl): 0
[movieplayer.cpp] URL :
http://192.168.0.7:8080/?sout=#duplicate{dst=std{a}
[movieplayer.cpp] URL(enc) :
http://192.168.0.7:8080/?sout=%23duplicate%7Bdst%3D
[sectionsd] getUTC: read: Connection timed out
[movieplayer.cpp] Server: 192.168.0.7
[movieplayer.cpp] Port: 8080
[movieplayer.cpp] Trying to connect socket
[movieplayer.cpp] Socket OK
[movieplayer.cpp] GET Sent
[movieplayer.cpp] VLC still does not send. Retrying...
[movieplayer.cpp] Trying to connect socket
[movieplayer.cpp] Socket OK
[movieplayer.cpp] GET Sent
[movieplayer.cpp] VLC still does not send. Retrying...
[movieplayer.cpp] Trying to connect socket
[movieplayer.cpp] Socket OK
[movieplayer.cpp] GET Sent
[movieplayer.cpp] Now VLC is sending. Read sockets created
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] ReceiveStreamThread: while streaming found pida: 0x0045 ; pid4
[movieplayer.cpp] PlayStreamthread: while streaming found pida: 0x0045 ; pidv: 4
[movieplayer.cpp] PlayStreamthread: Driver successfully set up
[controld] VIDEO_EVENT_SIZE_CHANGED 480x576 (4:3 -> 4:3)
[movieplayer.cpp] Resyncing
[movieplayer.cpp] Buffering approx. 3 seconds
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[movieplayer.cpp] Resyncing
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[sectionsd] getUTC: read: Connection timed out
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out
[movieplayer.cpp] Resyncing
[movieplayer.cpp] Resyncing
[sectionsd] getUTC: read: Connection timed out
[movieplayer.cpp] Resyncing
[movieplayer.cpp] Buffering approx. 3 seconds
[sectionsd] getUTC: read: Connection timed out
[movieplayer.cpp] Resyncing
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[movieplayer.cpp] Buffering approx. 3 seconds
[sectionsd] getUTC: read: Connection timed out
[movieplayer.cpp] Buffering approx. 3 seconds
[sectionsd] getUTC: read: Connection timed out
[movieplayer.cpp] Resyncing
[sectionsd] getUTC: read: Connection timed out
[movieplayer.cpp] Waiting for RCST to stop
[movieplayer.cpp] Seems that RCST was stopped succesfully
Was hältst du davon das MP-Einstellungen Menü da auch noch aufzunehmen?
