Loading graphical interface

Alles eine Frage des Images
computerfreak86
Neugieriger
Neugieriger
Beiträge: 14
Registriert: Donnerstag 20. Mai 2004, 18:15

Loading graphical interface

Beitrag von computerfreak86 »

HALLO,

Ich weiß nicht was ich machen soll, nach dem flashen und dem resetten bleibt meine box (nokia 2xintel) bei loading graphical interface stehen.....


HIER DER LOG

0
### FS (jffs2) loading 'vmlinuz' to 0x100000
Scanning JFFS2 FS: . done.
### FS load complete: 610191 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 610127 Bytes = 595.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.25-dbox2 (foer06@bsp-993) (gcc version 3.3.3) #5 Di Mai 11 16:
49:44 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock3 rootfstype=squashfs
Decrementer Frequency = 251625000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2580)
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30908k available (1032k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:45:1c:b8
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x000e0000 : "kernel (jffs2)"
0x000e0000-0x006a0000 : "root (squashfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS') multi-c
Using /lib/modules/2.4.25-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.25-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.25-dbox2/misc/avs.o
Using /lib/modules/2.4.25-dbox2/misc/saa7126.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.25-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.25-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.25-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.25-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.25-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.90 2004/03/17 10:44:15 diemade Exp $
SIOCADDRT: Network is unreachable
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.44 2003/12/22 05:31:39 obi Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.203 2004/04/07 23:17:45 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.38 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.25-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.25 2004/01/30 08:24:42 zwen Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.25-dbox2/misc/ves1820.o
Using /lib/modules/2.4.25-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1893)...
Using /lib/modules/2.4.25-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.25-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.199 2004/04/07 23:23:36 carjay Exp $
Using /lib/modules/2.4.25-dbox2/kernel/net/sunrpc/sunrpc.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/lockd/lockd.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/nfs/nfs.o
Using /lib/modules/2.4.25-dbox2/kernel/fs/cifs/cifs.o
Starting pid 81, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. [LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Micron/Regular)
[camd] ca system id: 1702
$Id: sectionsd.cpp,v 1.176 2004/04/29 09:11:13 metallica Exp $
caching 504 hours
events are old 180min after their end time
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[camd] /dev/dvb/adapter0/ca0: Device or resource busy
$Id: zapit.cpp,v 1.352 2004/05/06 12:44:40 thegoodguy Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
/var/tuxbox/config/zapit/services.xml: No such file or directory
$Id: controld.cpp,v 1.115 2004/02/19 23:00:33 zwen Exp $

[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1, Nokia D-BOX2)
[nhttpd] Neutrino HTTP-Server starting..
[ConfigFile] Unable to open file /var/tuxbox/config/nhttpd.conf for reading.
Bad emulation nhttpd/120
NIP: 10037d48 instruction: 7d60002d opcode: 1f A: 0 B: 0 C: 0 code: 16 rc: 1
pte @ 0x10037d48: (0xc1450100)->(0xc144b0dc)->0x013fd889
RPN: 013fd PP: 2 SPS: 1 SH: 0 CI: 0 v: 1
Kernel VA for NIP 0xc13fdd48 pte @ 0xc13fdd48: no pmd
Inconsistency detected by ld.so: dynamic-link.h: 62: elf_get_dynamic_info: Asser
tion `! "bad dynamic tag"' failed!
Segmentation fault
Segmentation fault
Segmentation fault
Segmentation fault
The system is going down NOW !!
Sending SIGTERM to all processeavia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_core: masking unhandled irq reg 0 bit 7
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
mogway
Semiprofi
Semiprofi
Beiträge: 1287
Registriert: Montag 30. Dezember 2002, 08:02

Beitrag von mogway »

Wenn ich das richtig sehe ist das ein jffs2 vom 05.05.

Da scheinen einige Dateien zu fehlen bzw falsch zu seinen, nimm mal ein aktuelles Yadi Image.

Gruss
mogway