Vielleicht ist meine Verson auch zu alt !?!?!?!
Zu 1. Ok, wenn nichts anderes hilft mach ich das mal. Ist es denn möglich die Sender zu speichern. Hab mir das extra alles schon eingestellt. Auch die Einstellungen würde ich gerne sichern. Sonst hab ich mal Pech gehabt.
Zu 2. Hat nix gebracht
Zu 3. Mhh, ich hoffe das ist nicht zuviel/zuwenig
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.0 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-f0.07.8b.07.00.00-29
debug: HWrev 01 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0040
will verify ELF image, start= 0x800000, size= 156828
verify sig: 263
Branching to 0x40000
U-Boot 1.1.1 (TuxBox) (Oct 30 2004 - 13:18:13)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .
.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load complete: 613263 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 613199 Bytes = 598.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (vom Jtg-Team) (gcc version 3.3.5) #2 Fri Oct 29 22:
09:59 CEST 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rootfstype=cramfs
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2580)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30900k available (1040k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (
rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:30:af:a3
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x006a0000 : "root (cramfs)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
route: SIOC[ADD|DEL]RT: Network is unreachable
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.27-dbox2/misc/avs.o
Using /lib/modules/2.4.27-dbox2/misc/saa7126.o
Using /lib/modules/2.4.27-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.27-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.27-dbox2/misc/avia_av.o
avia_av: $Id: avia_av_core.c,v 1.94 2004/07/03 01:18:36 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.27-dbox2/misc/aviaEXT.o
Using /lib/modules/2.4.27-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.47 2004/05/23 10:52:31 derget Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.27-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.27-dbox2/misc/ves1x93.o
DVB: registering frontend 0:0 (VES1993)...
Using /lib/modules/2.4.27-dbox2/misc/at76c651.o
Using /lib/modules/2.4.27-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.27-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.202 2004/06/24 00:26:58 carjay Exp $
jtginfo $Id: jtginfo.c,v 1.1 2004/05/31 16:00:30 jtgriker Exp $
$Id: sectionsd.cpp,v 1.179 2004/09/10 11:36:00 thegoodguy Exp $
caching 504 hours
events are old 180min after their end time
$Id: zapit.cpp,v 1.357 2004/10/27 16:08:42 lucgas Exp $
satelliteName = Amos 1 4.0W, satellitePosition = -40
satelliteName = Arabsat 26.0E, satellitePosition = 260
satelliteName = Arabsat 30.5E, satellitePosition = 305
satelliteName = Astra 19.2E, satellitePosition = 192
satelliteName = Astra 1A, Sirius 2/3 5.0E, satellitePosition = 50
satelliteName = Astra 23.5E, satellitePosition = 235
satelliteName = Astra 28.2E, satellitePosition = 282
satelliteName = Eurasia-/Tuerksat 42.0E, satellitePosition = 420
satelliteName = Eutelsat 10.0E, satellitePosition = 100
satelliteName = Eutelsat 13.0E, satellitePosition = 130
satelliteName = Eutelsat 16.0E, satellitePosition = 160
satelliteName = Eutelsat 7.0E, satellitePosition = 70
satelliteName = Eutelsat 8.0W, satellitePosition = -80
satelliteName = HispaSat/PAS 30.0W, satellitePosition = -300
satelliteName = Intelsat 707 1.0W, satellitePosition = -10
satelliteName = Telstar12 15.0W, satellitePosition = -150
satelliteName = Thor 2/3 0.8W, satellitePosition = -8
[camd] ca system id: 1702
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
[controld] setting VideoFormat to auto
[nhttpd] Neutrino HTTP-Server starting..
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[deutsch.locale] missing entry: movieplayer.pesplayback
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
[controld] setting VideoFormat to auto
loading locales: scandir: No such file or directory
[neutrino] received 17 sats
[neutrino] registering as event client
[controld] setting VideoFormat to auto
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] initialized everything
PES, queue 0 normal.
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3)
Das wäre sehr ärgerlich, aber nunja, mal gucken wie es nach dem Update aussieht. Danke schonmal, ich meld mich dann später obe geklappt hat oder nicht.
es hat nichts gebracht