ich habe den neuen CVS ausgecheckt und alles kompiliert.
Danach habe ich die Anpasungen aus "Howto JFFS2 Only Image erstellen Kernel 2.4.27 and newer" gemacht und image.img erstellt. Die Fuellung und Struktur ist, laut "New Tuxbox Flash Tools v0.1" im Ordnung (belegt
6,55MB). Nach dem Flashen kommt:
- Ndebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID xx-xx.xx.xx.xx.xx.xx-xx
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
will verify ELF image, start= 0x800000, size= 143992
verify sig: 262
Branching to 0x40000
U-Boot 0.4.5 (TuxBox) JFFS2 only (Jan 01 2004 - 18:47:07)
CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.0 -- Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ......
.
### FS (jffs2) loading 'var/tuxbox/boot/boot.conf'
### FS (jffs2) loading 'var/tuxbox/boot/u-boot.conf'
LCD: ready
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
### FS (jffs2) loading 'var/tuxbox/boot/logo-lcd'
### FS (jffs2) loading 'var/tuxbox/boot/logo-fb'
### FS (jffs2) loading 'vmlinuz'
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 625261 Bytes = 610.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (root@hades) (gcc version 3.3.5) #1 Wed May 4 23:01:3
3 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
console=ttyS0 line: root=/dev/mtdblock2 rw
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30876k available (1064k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:4c:f0
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x00800000 : "root (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
cramfs: wrong magic
VFS: Mounted root (jffs2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Ich habe nach einer Hilfestellung via letzten Zeilen gesucht, leider ohne Erfolg - koennte einer mir auf die Sprunge helfen?
Ich habe heute mind. drei mal alles neuinstalliert, CVS-ausgecheckt, kompiliert und.. gleiches Ergebnis..
Danke im Vorraus
dlubacz
P.S.
Linux auf dr Workstation ist SuSE 9.0 (leider brauche ich ihn fuer andere Projekte), Zeildbox ist Nokia-Sat 2x Intel..
P.S.(2)
Ich bin alleine etwas weiter gekommen
nur ein Problem habe ich weiter:
mein neues JFFS2-Only-Image wird nur Readonly geladen..!
Fuer die Hilfestellung, wie ich das abstellen kann, wuerde ich sehr dankbar.
- Vdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
..
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
will verify ELF image, start= 0x800000, size= 143992
verify sig: 262
Branching to 0x40000
U-Boot 0.4.5 (TuxBox) JFFS2 only (Jan 01 2004 - 18:47:07)
CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.0 -- Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ........
### FS (jffs2) loading 'var/tuxbox/boot/boot.conf'
### FS (jffs2) loading 'var/tuxbox/boot/u-boot.conf'
LCD: ready
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
### FS (jffs2) loading 'var/tuxbox/boot/logo-lcd'
### FS (jffs2) loading 'var/tuxbox/boot/logo-fb'
### FS (jffs2) loading 'vmlinuz'
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 625264 Bytes = 610.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.27-dbox2 (root@hades) (gcc version 3.3.5) #1 Thu May 5 15:21:0
9 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
console=ttyS0 line: root=/dev/mtdblock2 rw
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30876k available (1064k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Squashfs 2.1-r2 (released 2004/12/15) (C) 2002-2004 Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:42:4c:f0
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit mode
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Using word write method
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x00800000 : "root(jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
cramfs: wrong magic
VFS: Mounted root (jffs2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'ti-call b
/etc/init.d/rcS: 10: ./etc/profile: Permission denied
Using /lib/modules/2.4.27-dbox2/misc/tuxbox.o
Detected STB:
Vendor: Nokia
Model: D-BOX2
Using /lib/modules/2.4.27-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.27-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.27-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.27-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
..
/etc/init.d/rcS: 90: cannot create /etc/issue.net: Read-only file system
Starting pid 69, console /dev/console: '/etc/init.d/start'
..
[ConfigFile] Unable to open file /var/tuxbox/config/scan.conf for writing.
[ConfigFile] Unable to open file /var/tuxbox/config/neutrino.conf for writing.
..
Koennte mir jemand sagen, wie ich den neuen u-boot aktivieren kann:
neue cvs ist ausgecheckt, aber es kommt immer "U-Boot 0.4.5" nicht
1.xx .. und warum habe ich squashfs drin - ich habe "make all" und "make flash-neutrino-all" gemacht..
Gruesse und danke im Vorraus fuer die Hilfe.
dlubacz