URGENT HELP - DBOX2 not loading

Beitrag von **karimko** » Montag 12. September 2005, 13:12

Dear Friends,
I have a Nokia 2xI dbox2 , I have flashed it with an image and it seems it was wrong , now the receiver starts and i only see the boot screen then LOADING KERNEL ON LCD and nothing happens..
What can i do to solve this?
Now i don't know the IP of the box? anyway to do it?
Any other method to flash without knowing the IP of the box?
Is there a default IP??

regards Karim

Beitrag von **karimko** » Montag 12. September 2005, 13:45

I have succeeded in installing the image but now i have another problem.
the LCD shows : KEIN SYSTEM..any help?

http://www.dietmar-h.net/index.html
http://www.dietmar-h.net/flashprob_eng.html

Beitrag von **karimko** » Montag 12. September 2005, 14:29

M8,
I have flashed the right image and still the LCD showing : KEIN SYSTEM.

I'm stuck...what should i do?

Beitrag von **PT-1** » Montag 12. September 2005, 14:56

You must have flashed a 2 Flash Chip Image on a 1 Flash Chip Box or the other way around. Please download the right Image for your box.

Beitrag von **karimko** » Montag 12. September 2005, 15:02

I have a Nokia 2xI and i have flashed the right image...
Do you think the ucodes are the problem?? how can i sent them to box?

Beitrag von **PT-1** » Montag 12. September 2005, 15:06

Ucodes will only be loaded when you have the correct system on the box. Use ImageFlashing Assistant from http://www.hallenberg.com to make sure that you have the right Image as it checks what FlashChip type the Image is.

You can only upload the ucodes when the Image is up and running

Beitrag von **karimko** » Montag 12. September 2005, 15:59

Hi again,
I used the ImageFlashing Assistant and loaded the correct image , I'm sure i have a nokia 2xI cause i use to load firmwares always to this box but i had this problem cause i loaded a wrong firmware and my box showed LOADING KERNEL and stoped. then i used ImageFlashing Assistant to flash another image and i get KEIN SYSTEM and now stuck on this...

Beitrag von **karimko** » Montag 12. September 2005, 16:07

finally got my problem sorted out, thanks a lot for everyone who tried to help me especially PT-1 because of your insistence that everything must be up and running, i was using ImageFlashing Assistant english version so i downloaded the german version and installed a new firmare and now i have the box up and running...hope i don't need ucodes or anything else..how can i make sure everything is ok??

thx.

Beitrag von **karimko** » Montag 12. September 2005, 16:15

I have this message when i turn on the box:

Attention: Ucodes could not be found
Please upload them via ftp then restart your box.
I have avia 500

??????

Beitrag von **rasc** » Montag 12. September 2005, 17:29

So, upload your ucode files - these files are extracted from the original software (which are part of the dbox2, btw.). As an alternative, you may use the ucodes saved from the image which was o n the box prior to the reflash process (FAQ and docs always are saying: save your ucodes, you'll need 'em).

Still no ucodes at hand? Use the forces of the internet...
(ucodes are (c) and may not be redistributed!)

Any info where my ucodes should be saved on my computer?
If not available , anu ucodes on the net will do? and where to transfer them? which directory on dbox?

regards