nokia dbox2 kabel display prob.

[woody´s]

hallo,
hab an meiner dbox2 ein neues display einbauen wollen, da das alte defekt war
nach dem einschalten der box leutet das neue display nur noch aber zeigt nichts an!

Box starte aber ganz normal!

Weiß einer was ich machen kann um das display wieder zum laufen zu bringen?

Gruß woody

[simon851]

Den Anschluss vom Display nochmal überprüfen.
Wenn die Box einwandfrei bootet und arbeitet wirds am Prozessor nicht liegen.

[woody´s]

hab eben nochmal die box mit der hallenberg ide flashsoftware geflash

und das ist das log von

â„¢debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: LCD init error -1
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID http://Hallenberg.com
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
debug: autoboot aborted from terminal
dbox2:root>
dbox2:root> boot net net net net net net net net net net
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.0.1, My IP 192.168.0.202
debug: Sending TFTP-request for file N/dboxifa_tmp/tftpboot/u-boot
will verify ELF image, start= 0x800000, size= 140336
verify sig: 263
boot net: boot file has no valid signature
Branching to 0x40000


U-Boot 1.1.2 (Tuxbox) (Jun 12 2005 - 13:44:14)

CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'N/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename '/tftpboot/logo-lcd'.
Load address: 0x100000
Loading: *##

Bytes transferred = 7680 (1e00 hex)
BOOTP broadcast 1
Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'N/dboxifa_tmp/tftpboot/u-boot'.
Load address: 0x100000
Loading: *Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename '/tftpboot/logo-fb'.
Load address: 0x100000
Loading: *####################################

Bytes transferred = 179877 (2bea5 hex)

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0

Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit

Size: 8192 kB in 71 Sectors

Using SCC ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.202
Filename 'kernel-yadd'.
Load address: 0x100000
Loading: *#################################################################
#################################################################
####################

Bytes transferred = 763552 (ba6a0 hex)
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 763488 Bytes = 745.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
dbox2 - ImageFlashingAssistent

- Hallenberg.com -

Sie koennen die dbox jetzt ausschalten.

Please press Enter to activate this console.
------ Zusatzinformationen ------
Gewählter Netzwerkadapter: Realtek RTL8139-Familie-PCI-Fast Ethernet-NIC - Paketplaner-Miniport (0)
IP-Adresse des Netzwerkadapters: 192.168.0.1
IP-Adresse die die dbox bekommt: 192.168.0.202
Comport: Prolific USB-to-Serial Bridge (COM3)
Betriebssystem: Microsoft Windows XP Professional Service Pack 2 (Build 2600)
CPU 1: Intel(R) Celeron(R) CPU 2.40GHz @ 2390 MHz
Dateiname des Images: JTG_070806_2x_KABEL.img
Imagetyp: Zwei Flashs
DBOX-IFA Version: 2.1
------ Powered by http://www.dboxservice-hallenberg.de ------

[woody´s]

so hab neu gestartet und nun komt diese sache

¹debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: LCD init error -1
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-60.e7.2d.07.00.00-e2
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0040

will verify ELF image, start= 0x800000, size= 158020
verify sig: 262
Branching to 0x40000


U-Boot 1.1.4 (Tuxbox) (Aug 7 2006 - 21:15:08)

CPU: PPC823ZTnnB2 at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . .
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 759063 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 758999 Bytes = 741.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Ch
Uncompressing Kernel Image ... OK
Linux version 2.4.32-dbox2 (vom Jtg-Team) (gcc version 3.4.4) #3 Mo Aug 7 20:59
:49 CEST 2006
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rootfstype=squashfs
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30644k available (1296k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT n
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1b:96:95
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (SquashFS)"
0x006a0000-0x00800000 : "var (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 10, console /dev/console: '/etc/init.d/rcS'lti-call
Starting the automounter
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Thu Jan 1 12:00:00 CET 1970
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
avia_av_core: Starting avia_av_wdt thread.
avia_av: microcode verify: 1407 errors.
avia_av: imem verify: 98 errors
avia_av: timeout waiting for decoder init to complete. (00000001)
insmod: init_module: avia_av: Input/output error
insmod: unresolved symbol avia_av_set_stc
insmod: unresolved symbol avia_gt_gv_copyarea
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_get_blevel
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
jtginfo $Id: jtginfo.c,v 1.7 2006/08/01 22:04:55 jtgriker Exp $
insmod: unresolved symbol avia_gt_ir_exit
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_init
insmod: unresolved symbol avia_gt_ir_set_duty_cycle
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
insmod: unresolved symbol avia_av_set_sample_rate
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_av_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
insmod: unresolved symbol avia_gt_pig_show
insmod: unresolved symbol avia_gt_pig_set_stack
insmod: unresolved symbol avia_gt_pig_set_size
insmod: unresolved symbol avia_gt_pig_set_pos
insmod: unresolved symbol avia_gt_pig_hide
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C f
insmod: unresolved symbol avia_av_stream_type_set
insmod: unresolved symbol avia_av_register_video_event_handler
insmod: unresolved symbol avia_av_set_audio_attenuation
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_av_pid_set
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_play_state_set_video
insmod: unresolved symbol avia_av_unregister_video_event_handler
insmod: unresolved symbol avia_av_get_video_size
insmod: unresolved symbol avia_av_play_state_set_audio
insmod: unresolved symbol avia_av_read
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_set_video_system
insmod: unresolved symbol avia_av_bypass_mode_set
insmod: unresolved symbol avia_av_sync_mode_set
insmod: unresolved symbol avia_gt_dmx_queue_nr_get
insmod: unresolved symbol avia_gt_dmx_get_ucode_info
insmod: unresolved symbol avia_gt_vbi_start
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol avia_av_napi_decoder_stop
insmod: unresolved symbol avia_gt_dmx_queue_stop
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_vbi_stop
insmod: unresolved symbol avia_av_audio_pts_to_stc
insmod: unresolved symbol avia_gt_dmx_queue_write
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_enable_clip_mode
insmod: unresolved symbol avia_gt_dmx_disable_framer
insmod: unresolved symbol avia_gt_dmx_disable_clip_mode
insmod: unresolved symbol avia_av_napi_decoder_start
insmod: unresolved symbol avia_gt_dmx_queue_start
insmod: unresolved symbol avia_gt_dmx_tap
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_enable_framer
insmod: unresolved symbol avia_gt_dmx_alloc_queue_vide
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_dmx_get_stc
insmod: unresolved symbol avia_gt_accel_crc32
insmod: unresolved symbol avia_gt_napi_dvr_send
insmod: unresolved symbol avia_av_write
insmod: unresolved symbol avia_gt_set_playback_mode
insmod: unresolved symbol avia_gt_get_playback_mode
insmod: unresolved symbol avia_av_is500
insmod: unresolved symbol avia_av
insmod: unresolved symbol avia_av_new_audio_config
insmod: unresolved symbol avia_av_cmd
$Id: sectionsd.cpp,v 1.227 2006/06/08 20:19:32 houdini Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Events are old 60min after their end time
[sectionsd] open dmx: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
[sectionsd] open dmx: No such file or directory
$Id: zapit.cpp,v 1.389 2006/06/08 20:17:58 houdini Exp $
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
/tmp/currentservices.xml: No such file or directory
[audio.cpp:CAudio:34] /dev/dvb/adapter0/audio0: No such file or directory
[video.cpp:CVideo:33] /dev/dvb/adapter0/video0: No such file or directory
[camd] /dev/dvb/adapter0/demux0: No such file or directory
[aviaext.cpp:CAViAext:37] /dev/dbox/aviaEXT: No such file or directory
[sectionsd] getUTC: open: No such file or directory
$Id: controld.cpp,v 1.124 2006/06/27 10:21:59 barf Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld] /dev/dvb/adapter0/video0: No such file or directory
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[controld] /dev/dvb/adapter0/video0: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] getUTC: open: No such file or directory
[LCDFONT] initializing core...[sectionsd] getUTC: open: No such file or director
y

[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...[sectionsd] getUTC: open: No s
uch file or directory
OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[sectionsd] getUTC: open: No such file or directory
/bin/neutrino: /lib/libpng12.so.0: no version information available (required by
/bin/neutrino)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
FBIOGET_FSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
zapit shot down
Waiting for controld (max. 5 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 4 seconds)
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 3 seconds)
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 2 seconds)
[sectionsd] getUTC: open: No such file or directory
Waiting for controld (max. 1 seconds)
[sectionsd] getUTC: open: No such file or directory
[sectionsd] getUTC: open: No such file or directory
Going to halt system now ...
Starting pid 158, console /dev/console: '/etc/init.d/halt'
CXA2092 found
CXA2092 found
[sectionsd] getUTC: open: No such file or directory
Unmounting 'ramfs' on '/tmp'
umount: Couldn't umount /tmp: No such file or directory
Unmounting 'jffs2' on '/var'
[sectionsd] getUTC: open: No such file or directory
Ready to shutdown system...
The system is going down NOW !![ConfigFile] Unable to open file /var/tuxbox/conf
ig/controld.conf for writing.
[nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted.