ich würde meine Sagem dbox2 SAT gerne mit einem aktuellen Neutrino-Image updaten.
Wie bekomme ich raus, ob ich das 1X oder 2X Image brauche.
Was sollte ich vorher von der Box sichern?
Habe ein älteres Image, die Meldung bei Telnet ist:
Code: Alles auswählen
Willkommen auf dem Nais2000 Release! Viel Spass mit Deiner Sagem D-BOX2 - Kernel 2.4.27-dbox2 (09:02:51).
dbox login: root
BusyBox v1.00 (2004.10.16-18:23+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/var #Code: Alles auswählen
/var # dmesg
Linux version 2.4.27-dbox2 (nais2000@nais) (gcc version 3.3.4) #67 Sa Nov 6 16:45:26 CET 2004
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=null root=/dev/mtdblock3 rootfstype=squashfs
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30888k available (1052k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
i2c-core.o: driver i2c-dev dummy driver registered.
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRG1
ttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:30:fd:77
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
CFI: Found no D-Box 2 flash memory device at location zero
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit mode
Intel/Sharp Extended Query Table at 0x0031
cfi_cmdset_0001: Erase suspend on write enabled
0: offset=0x0,size=0x20000,blocks=64
Using buffer write method
Creating 7 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (u-boot)"
0x00040000-0x000e0000 : "kernel (jffs2)"
0x000e0000-0x005a0000 : "root (squashfs)"
0x005a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Warning: unable to open an initial console.
[i2c-8xx]: mpc 8xx i2c init
i2c-dev.o: Registered 'PowerPC 8xx I2C adapter' as minor 0
i2c-core.o: adapter PowerPC 8xx I2C adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [PowerPC 8xx I2C adapter](pos. 0).
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [PowerPC 8xx I2C adapter](pos. 1).
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos. 2).
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
i2c-core.o: driver DBox2-CAM registered.
i2c-core.o: client [DBox2-CAM] registered to adapter [PowerPC 8xx I2C adapter](pos. 3).
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
DVB: registering frontend 0:0 (VES1993)...
i2c-core.o: client [DVB I2C bridge] registered to adapter [PowerPC 8xx I2C adapter](pos. 4).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
avia_av: $Id: avia_av_core.c,v 1.94 2004/07/03 01:18:36 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.47 2004/05/23 10:52:31 derget Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_proc: Using config file '/var/tuxbox/config/avia.conf'.
avia_gt_proc: $Id: avia_gt_proc.c,v 0.92d 2003/06/18 19:00:00 bofh Exp $
avia_gt_proc: found - AVIA eNX
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.202 2004/06/24 00:26:58 carjay Exp $
DBox2 Multicam Driver v1.01 skars & doz21 :)
[camd-cardserver.o] compiled Jan 23 2004, 16:38:42
[camd-cardserver.o] ioport base = ff000950
[camd-cardserver.o] commproc base = ff0009c0
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
CIFS: Unknown mount option udp
CIFS: Unknown mount option nolock
CIFS: Unknown mount option udp
CIFS: Unknown mount option nolock
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -113
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -113
CIFS: Unknown mount option udp
CIFS: Unknown mount option nolock
CIFS VFS: Error connecting to IPv4 socket. Aborting operation
CIFS VFS: cifs_mount failed w/return code = -113
jffs2_reserve_space(): Low on dirty space to GC, but it's a deletion. Allowing...
PES, queue 0 normal.
PES, queue 0 normal.
PES, queue 0 normal.
PES, queue 0 normal.
avia_av_wdt_thread: video decoding stopped ==> restart
PES, queue 0 normal.
PES, queue 0 normal.
PES, queue 0 normal.
CIFS: Unknown mount option udp
CIFS: Unknown mount option nolock
/var #
Die Dbox spuckt unter Services aus:
Installierte Version
Datum: 06.11.2004
Uhrzeit: 16:50
Releasezyklus: 2.0
Imagetyp: Release
Und das sagt mir das Hallenberg-Tool über die ucodes:
Code: Alles auswählen
avia500.ux: avia500v110, MD5: 7373f3934263b3c3ea1d0f500f0044a5
avia600.ux: avia600vb028, MD5: f8577c6a7056590ca5847520d81339fc
cam-alpha.bin: cam_01_02_002E, MD5: 7f56e693a916b39a6e2734dc9b5aab7a
ucode.bin: ucode_0014, MD5: 6582a89e7e13e410c366e47b4ef9d38e
Habe jetzt schon eine Weile gesucht, aber irgendwie habe ich nur die Bilder gefunden von den Chips.
Edit: Ich suche immer noch und mich ärgert das richtig, da ich eigentlich mich gar nicht so blöd beim Suchen anstelle. Für nen Hinweis, der das Brett vor meinem Kopf etwas in Bewegung bringt, wäre ich sehr dankbar.
http://wiki.tuxbox-cvs.sourceforge.net/ ... lash_Chips hab ich schon gefunden. Aber danach können ja beide Versionen (1x oder 2x) in meiner Sagem sein. Hier im Forum lese ich dagegen meist von 1xI Sagems.
ciao
frank
