nokia & sagem no display??

The forum for our foreign guests... Please post in English
senengineer
Neugieriger
Neugieriger
Beiträge: 11
Registriert: Montag 25. Oktober 2004, 00:03

nokia & sagem no display??

Beitrag von senengineer »

Hi, everyone, my appoligise if this is in the wrong section or forum but I have no idea who or where to ask.

I have now two dbox2's both with the same symptom's.

First is a nokia cable 2xI, there is nothing on the screen except a dim light, this box worked for two weeks then nothing.

Second is a Sagem cable 2xI, this one I stuffed myself by doing it the same way as the bmon 1.0, but it was a bmon 1.2, but the syptoms are exactly the same as above.

I have taken the 28f320 chips out & re-flashed them with ones from the same boxes (nokia 2xI & sagem 2xI ) but there is no change???

I have checked the flash checksums with the copied ones & they are the same? I have no idea where to start looking??

p.s. I am a qualified electronics engineer, so I have access to any equipment needed.

I hope someone help as I am now stuck & no idea what to try next.

Thanks in advance.
S.E.
DieMade
Oberlamer, Administrator & Supernanny
Beiträge: 10532
Registriert: Samstag 13. Juli 2002, 10:49

Beitrag von DieMade »

Maybe you mixed the Flashs (IH2 soldered on IH5 and vice versa).

Does the CPU read out some data from the Flashs (measure address and data-pins with an osciloscope). Does the CPU run on 16MHz (default) or 66MHz (first few Bytes of the BMon set it to that frequency) - for Nokia the freq. is on RPN1 - Sagem I don't know right now.
There are 10 types of people in the world: those who know binary and those who don't
senengineer
Neugieriger
Neugieriger
Beiträge: 11
Registriert: Montag 25. Oktober 2004, 00:03

Beitrag von senengineer »

Hi m8, thanks for the reply, I checked & double checked that I had the correct on in the right place, even to re-moving & flashing one at a time, but still the same, I must admit to not checking the prosessor as was not sure of what & where to start, but now I shall do the checks you suggest, Just a quick one though, the bmon does not even make any attempt to start, just compleatly blank execept for a smallll brightness in the display....
Once again thanks for the tips....more would certainly help...thanks..
S.E.
DieMade
Oberlamer, Administrator & Supernanny
Beiträge: 10532
Registriert: Samstag 13. Juli 2002, 10:49

Beitrag von DieMade »

Well, a lot of things get initialized even before the LCD ;)
There are 10 types of people in the world: those who know binary and those who don't
senengineer
Neugieriger
Neugieriger
Beiträge: 11
Registriert: Montag 25. Oktober 2004, 00:03

Beitrag von senengineer »

wish there was a circuit diagram!! would make my life a bit easier...
doc
Contributor
Beiträge: 1623
Registriert: Donnerstag 10. Januar 2002, 20:03

Beitrag von doc »

for Nokia??

You should find them in the WWW! :wink:
Na schönen Dank Herr Schwanke!
Ein toller Sommer! :-(
senengineer
Neugieriger
Neugieriger
Beiträge: 11
Registriert: Montag 25. Oktober 2004, 00:03

Beitrag von senengineer »

You should find them in the WWW!
www what though??? I have looked most places??? a point in the right direction would help...

S.E.
DrStoned
Tuxboxer
Tuxboxer
Beiträge: 2614
Registriert: Montag 20. Mai 2002, 10:49
Image: JTG-Image [IDE] Version 2.4.4
Image: (7025SS) Merlin

Beitrag von DrStoned »

Look at your mailbox.

Greetz from DrStoned :lol: :lol: :lol:
Greetz von DrStoned :lol: :lol: :lol:
senengineer
Neugieriger
Neugieriger
Beiträge: 11
Registriert: Montag 25. Oktober 2004, 00:03

Beitrag von senengineer »

Thank you. most appreciated