filename falsch!!!!!!!!!!!!!

[candy]

hallo hier mein com log:
wdebug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.1 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-bb.15.0a.08.00.00-52
debug: HWrev 41 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/o
debug: Got Block #0052

will verify ELF image, start= 0x800000, size= 203252
verify sig: 262
Branching to 0x40000


PPCBoot 1.1.6 (TuxBox) (Jul 12 2002 - 20:57:43)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Watchdog enabled
Board: DBOX2, Sagem
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .. .
LCD: ready
FB: loading - ready
In: serial
Out: serial
Err: serial

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select (1-3), other keys to stop
...............................................................
Un-Protected 63 sectors
### FS (cramfs) loading 'vmlinuz' to 0x100000
### FS load compleate: 634725 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 634661 Bytes = 619 kB = 0 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.20 (von alexW) Wer Kernels na
raft ;-) #1 Die Dez 31 18:36:38 CET 2002
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 console=ttyS0
Decrementer Frequency = 247500000/60
mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30816k available (1120k kernel code, 372k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
i2c-core.o: i2c core module
CPM UART driver version 0.03
ttyS00 at 0x0280 is a SMC
ttyS01 at 0x0380 is a SMC
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:3c:f7:c2
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
Amd/Fujitsu Extended Query Table v1.2 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Creating 6 MTD partitions on "D-Box 2 flash
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "flfs (ppcboot)"
0x00040000-0x00720000 : "root (cramfs)"
0x00720000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "flash without bootloader"
0x00000000-0x00800000 : "complete flash"
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu
les/2.4.20/misc/i2c-8xx.o
[i2c-8xx]: mpc 8xx i2c init
i2c-core.o: adapter registered as adapter 0.
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.20/misc/info.o
i2c-core.o: driver FOR_PROBE_ONLY registered.
i2c-core.o: driver unregistered: FOR_PROBE_ONLY
Using /lib/modules/2.4.20/misc/event.o
event: init ...
Using /lib/modules/2
i2c-core.o: driver i2c audio/video switch driver registered.
i2c-core.o: client [CXA2126] registered to adapter [](pos. 0).
Using /lib/modules/2.4.20/misc/saa7126.o
i2c-core.o: driver i2c saa7126 driver registered.
i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 1).
Using /lib/modules/2.4.20/misc/fp.o
i2c-core.o: driver DBox2 Frontprocessor driver registered.
i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2
).
Using /lib/modules/2.4.20/misc/dvb_demux.o
Using /lib/modules/2.4.20/misc/dvbdev.o
Using /lib/modules/2.4.20/misc/avia.o
AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $
avia_core.c: do_firmread: Unable to load '/var/tuxbox/ucodes/avia600.ux'.
insmod: init_module: avia: Input/output error
Using /lib/modules/2.4.20/misc/cam.o
insmod: init_module: cam: Input/output error
Using /lib/modules/2.4.20/misc/dmxdev.o
Using /lib/modules/2.4.20/misc/dvb_frontend.o
Using /lib/modules/2.4.20/misc/avia_gt.o
insmod: unresolved symbol avia_set_pcr
Using /lib/modules/2.4.20/misc/dvb.o
insmod: unresolved symbol avia_wait
insmod: unresolved symbol avia_wr
insmod: unresolved symbol avia_command
insmod: unresolved symbol avia_rd
insmod: unresolved symbol avia_flush_pcr
insmod: unresolved symbol cam_read_message
insmod: unresolved symbol cam_reset
insmod: unresolved symbol avia_gt_pcm_set_mpeg_attenuation
insmod: unresolved symbol cam_write_message
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
Init AT76C651
Using /lib/modules/2.4.20/misc/at76c651.o
insmod: unresolved symbol register_frontend
insmod: unresolved symbol unregister_frontend
Using /lib/modules/2.4.20/misc/avia_gt_napi.o
insmod: unresolved symbol avia_gt_dmx_queue_reset
insmod: unresolved symbol unregister_demux
insmod: unresolved symbol avia_gt_dmx_queue_irq_enable
insmod: unresolved symbol avia_gt_dmx_set_pcr_pid
insmod: unresolved symbol avia_gt_dmx_release_section_filter
insmod: unresolved symbol avia_gt_dmx_alloc_queue_teletext
insmod: unresolved symbol avia_gt_dmx_fake_queue_irq
insmod: unresolved symbol avia_gt_dmx_get_queue_irq
insmod: unresolved symbol avia_gt_dmx_set_filter_parameter_table
insmod: unresolved symbol register_demux
insmod: unresolved symbol avia_gt_dmx_set_pid_table
insmod: unresolved symbol avia_gt_dmx_force_discontinuity
insmod: unresolved symbol avia_gt_dmx_set_pid_control_table
insmod: unresolved symbol avia_gt_dmx_get_hw_sec_filt_avail
insmod: unresolved symbol avia_gt_dmx_get_queue_info
insmod: unresolved symbol avia_gt_dmx_set_section_filter
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_dmx_alloc_queue_video
insmod: unresolved symbol avia_gt_dmx_free_queue
insmod: unresolved symbol avia_gt_dmx_queue_irq_disable
insmod: unresolved symbol avia_gt_dmx_alloc_queue_audio
insmod: unresolved symbol avia_gt_dmx_alloc_queue_message
insmod: unresolved symbol avia_gt_dmx_alloc_queue_user
insmod: unresolved symbol avia_gt_free_irq
Using /lib/modules/2.4.20/misc/avia_gt_vbi.o
insmod: unresolved symbol avia_gt_get_info
Using /lib/modules/2.4.20/misc/avia_gt_fb.o
insmod: unresolved symbol avia_gt_gv_show
insmod: unresolved symbol avia_gt_gv_get_clut
insmod: unresolved symbol avia_gt_gv_set_input_size
insmod: unresolved symbol avia_gt_gv_set_pos
insmod: unresolved symbol avia_gt_gv_hide
insmod: unresolved symbol avia_gt_get_info
insmod: unresolved symbol avia_gt_gv_set_size
insmod: unresolved symbol avia_gt_gv_set_input_mode
insmod: unresolved symbol avia_gt_gv_set_clut
insmod: unresolved symbol avia_gt_gv_set_blevel
insmod: unresolved symbol avia_gt_gv_get_info
Using /lib/modules/2.4.20/misc/avia_gt_oss.o
insmod: unresolved symbol avia_gt_pcm_play_buffer
insmod: unresolved symbol avia_gt_pcm_stop
insmod: unresolved symbol avia_gt_pcm_set_signed
insmod: unresolved symbol avia_gt_pcm_set_endian
insmod: unresolved symbol avia_gt_pcm_set_rate
insmod: unresolved symbol avia_standby
insmod: unresolved symbol avia_gt_pcm_set_width
insmod: unresolved symbol avia_gt_pcm_poll
insmod: unresolved symbol avia_get_sample_rate
insmod: unresolved symbol avia_gt_pcm_set_channels
insmod: unresolved symbol avia_gt_pcm_set_pcm_attenuation
insmod: unresolved symbol avia_gt_pcm_get_block_size
Using /lib/modules/2.4.20/misc/avia_gt_lirc.o
insmod: unresolved symbol avia_gt_ir_receive_pulse
insmod: unresolved symbol avia_gt_ir_receive_data
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_write_position
insmod: unresolved symbol avia_gt_ir_send_buffer
insmod: unresolved symbol avia_gt_ir_queue_pulse
insmod: unresolved symbol avia_gt_ir_set_dut
insmod: unresolved symbol avia_gt_ir_set_frequency
insmod: unresolved symbol avia_gt_ir_get_rx_buffer_read_position
Using /lib/modules/2.4.20/misc/lcd.o
cdkVcInfo $Id: cdkVcInfo.c,v 1.1 2002/12/19 16:10:45 alexW Exp $
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface on 3

$Id: sectionsd.cpp,v 1.148 2002/12/09 20:07:52 thegoodguy Exp $
caching 504 hours
events are old 60min after their end time
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[camd] /dev/dvb/card0/ca0: No such file or directory
$Id: zapit.cpp,v 1.286 2003/01/03 12:41:31 alexw Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conffor reading.

[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or direct
[frontend.cpp:CFrontend:62] /dev/dvb/card0/frontend0: No such file or directory
[zapit] unable to open frontend devices. bye.
Controld $Id: controld.cpp,v 1.88 2003/01/07 19:08:27 Zwen Exp $

/var/t[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
uxbox/config/controld.conf: skipping line 1: 2
[controld] Boxtype detected: (03, 3, 2, Sagem)
set event: 00000009
[nhttpd] Neutrino HTTP-Server starting..
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[CBasicClient] connect failed
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.389 2003/01/12 16:41:17 Zwen Exp $
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory

[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[lcdd] load config
[FONT] initializing core...[sectionsd] DMX: /dev/dvb/card0/demux0: No such file
or directory

[FONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[FONT] Intializing font cache...
[FONT] FTC_Face_Requester (Micron/Regular)
[neutrino] frameBuffer Instance created
/dev/fb/0: No such file or directory
framebuffer not available.
FBIOPUT_VSCREENINFO: Bad file descriptor
[neutrino] Error while setting framebuffer mode
CXA2126 found
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
Unmounting 'ramfs' on '/tmp'
umount: /tmp: Device or resource busy
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
Unmounting 'jffs2' on '/var'
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
[sectionsd] DMX: /dev/dvb/card0/demux0: No such file or directory
Ready to shutdown system...

Sending SIGTERM to all processes.[nhttpd] stop requested......
Sending SIGKILL to all processes.
The system is halted. Press Reset or turn off power
System haltý

[Dietmar]

Wenns das Log vom flashen war: boot net failed -> Netzwerkprobleme
Wenns das Log vom normalen Start war: Ucodes reinkopieren.

[candy]

@Dietmar
das war gerade der log vom normalen start! ok die ucodes hab ich, aber wie greife ich auf die box zu, wenn rote oder grüne led leuchtet?

frank

[Dietmar]

ÖH, LED? Ägypten?

Starte am einfachsten mit maintaince und angehängtem Nullmodem.
So wie eben halt.
Pin: 0000

Dann mit Enter die console aktivieren.

ifconfig eth0 192.168.1.153 netmask 255.255.255.0 broadcast 192.168.1.255
(oder was immer Du gerne für eine IP für die Box hättest)

Dann kannst die Ucodes ganz normal mit FTP hochkopieren.

[candy]

So wie eben halt.
.

Vielleicht habe ich eben was gemacht ohne es zu wissen also langsam soll ich den bootmanager oder z.b hyperterminal als konsole nehmen? und wie benutze ich dann diesen maint.....zugang. ich habe die suchfunktion genutzt um in den faq zu lesen aber nix gefunden!
danke
frank

[candy]

hab gerade noch mal ein log vom flashen gemacht! was heisst den in den letzten zeile invalide filename? habe ich das falsche image?
debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.1 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-bb.15.0a.08.00.00-52
debug: HWrev 41 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Got BOOTP reply from Server IP 192.168.1.7, My IP 192.168.1.29
debug: Sending TFTP-request for file F/Programme/DBoxBoot/ppcboot_writeflash
will verify ELF image, start= 0x800000, size= 201596
verify sig: 262
boot net: boot file has no valid signature
Branching to 0x40000


ppcboot 0.6.4 (Apr 11 2002 - 16:10:44)

Initializing...
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: ### No HW ID - assuming TQM8xxL
DRAM: (faked) 32 MB
Ethernet: 00-50-9c-3c-f7-c2
FLASH: 8 MB
LCD driver (KS0713) initialized
BOOTP broadcast 1
TFTP from server 192.168.1.7; our IP address is 192.168.1.29
Filename 'F/Programme/tftpboot/logo-lcd'.
Load address: 0x130000
Loading: ##

LCD logo at: 0x130000 (0x1F9FFC0 bytes)
BOOTP broadcast 1
TFTP from server 192.168.1.7; our IP address is 192.168.1.29
Filename 'F/Programme/tftpboot/logo-fb'.
Load address: 0x120000
Loading: #########

FB logo at: 0x0 (0x1FC0000 bytes)
AVIA Frambuffer
Input: serial
Output: serial


1: Console on ttyS0
2: Console on null
3: Console on framebuffer
Select (1-3), other keys to stop autoboot: 0
dbox2-ppcboot> bootp 120000 /C/dbox/alexW2xBaseimageV1.6.3.img
BOOTP broadcast 1
TFTP from server 192.168.1.1; our IP address is 192.168.1.211
Filename '/C/dbox/alexW2xBaseimageV1.6.3.img'.
Load address: 0x120000
Loading: *
TFTP error: 'Invalid filename. ( reset, upgrade ,IGATE15.BIN )' (1)

dbox2-ppcboot>

[candy]

nochwas: ich lese immer auswahlbilschirm wg. enigma lcars oder maintance! sowas habe ich nicht beim start! also biiiiittte nochmal ganz langsam: wie komme ich mit dem main..... in die box?
danke
frank

[Dietmar]

Hm, komischer Fehler.
Virenscanner und Firewall sind sicher raus?
Kommt das jedesmal?

[candy]

Au mann! Mir kam der Name igate15.bin schon sehr bekannt vor! So heisst die upgradedatei der Firmware vom Router!! Aber was hat das mit der box zu tun???????

gruss
frank

[DieMade]

Lass mich raten, Du hast nen Logshine-Router/Firewall für den DSL-Zugang (LCS-883R-DSL-4F) laufen.

Für den ist nämlich diese Imagedatei gedacht.

Läuft irgendwelche Software für den Router auf einem PC im Netz?

[candy]

Der Router heisst zwar nicht so aber ich gerade das Handbuch des Longshine im Netz gefunden und die Abbildungen sind genau wie bei meinem Router meine Firmware kriege ich auf http://www.01tech.com ist bestimmt der gleiche Hersteller! Ne eine Software läuft nicht auf dem PC! Glaub ich Ich konfiguriere den Router von meinem PC sonst nix! Hmm!!!
gruss

frank

[candy]

habe gerade auf der longshine seite geschaut. mein router ist identisch.
gruss

frank

[DieMade]

Aha. Ich wette, daß die SW nen TFTP-Server laufen hat.

Probier mal nen anderen Rechner, mit isoliertem Netzwerk (nur PC & Box).

[candy]

HAbe mal im Router-forum.de gepostet, vielleicht weiss da einer wg. der Firmwaredatei Rat. Ich habe eben den Router nochmal resetet und die Firmware neu aufgespielt....immernoch gleiche Problem.
Da ich kein Crossoverkabel da habe folgende Idee: Wenn ich nur die Box und meinen PC mittels Hub verbinde, kann ich ja ein normales Patchkabel nehmen wg. der Uplinkbuchse(die ist doch schon gedreht) oder?

gruss

frank

[DieMade]

Jep. Und den Router mal ganz abklemmen.

Wenn dann immernoch die ominöse Datei gesucht wird, bietet der PC doch den Dienst zum Update des Routers an.

[candy]

Geklappt! Aber mit meinem nächsten Problem bin ich hier vielleicht im falschen Thread! Es klappt alles soweit EPG und Menüs alles da! Nur sehe ich nur Ard und Konsorten und bei Premieresendern sehe ich nur unten das Menü! HAbe ich die falschen Ucodes hochgeladen? Habe die etwas gewürfelt auf meinem PC, habe wohl die Übersicht verloren
danke

frank

[Dietmar]

Was spricht denn Neutrino -> Service -> Ucodes überprüfen?
Schau auch mal hier: http://www.dietmar-h.net/ucodes.html